Peugeot 307 SW 2004 Owner's Guide

15-03-200415-03-2004
3031YOUR 307 SW IN DETAIL
ButtonFunction
A Radio on/off.
B - Decrease volume.
C + Increase volume.
D RDS RDS function on/off.
Press for more than 2 seconds: regional following mode on/off.
E TA Trafic information priority on/off.
F Press fully: cassette rewind.
G Press fully: fast forward.
F + G 3478Press half way: reversal of direction of play of the cassette.
Press fully: ejection of the cassette.
H
¯Selection of bass, treble, loudness, sound distribution and a utomatic volume correction.
I 5Increase setting of functions associated with button
H.
J 6Decrease setting of functions associated with button
H.
K SRC Selection of source: radio, cassette or CD changer.
Press for more than 2 seconds: CD shufle.
L 8Manual and automatic search of higher frequency.
Selection of next CD track and PTY (radio).
M MAN Manual/automatic operation of buttons L and N in radio mode.
N 7Manual and automatic search of lower frequency.
Selection of previous CD track and PTY (radio).
O BND
AST Selection of FM1, FM2, FMast and AM wavebands.
Press for more than 2 seconds: automatic storing of stations in the
memory (autostore).
1 to 6 1 2 3 4 5 6 Selection of station stored in the memory.
Press for more than 2 seconds: storing of a station in the memory.
1 to 5 1 2 3 4 5 Selection of a CD changer disc.

15-03-200415-03-2004
3435YOUR 307 SW IN DETAIL
GENERAL FUNCTIONS AUDIO SETTINGS
Adjusting the loudness
This function automatically emphasis-
es bass and treble tones. Press button
I or J to switch the function on or off.
On/off
With the ignition key
in the accessories or
ignition position, press
button
A to switch the
set on or off.
The set can operate for
30 minutes without the
vehicle ignition being switched on.
Anti-theft system
The audio system is coded in such a
way that it can operate only on your
vehicle. It would not function if itted
to another vehicle.
The anti-theft system is automatic
and requires no action on your part.
ADJUSTING THE VOLUME
Press button C to increase the volume,
or button B to decrease it.
Continuous pressure on buttons C and
B allows a gradual adjustment of the
volume. Adjusting the bass
Adjusting the treble
When
"TREB" is displayed, press
button I or J to vary the setting.
-
"TREB -9" for a minimum treble setting,- "TREB 0" for a normal setting,
- "TREB +9" for a maximum treble setting.
Press button H several
times in succession
to access the bass
(BASS) , treble (TREB) ,
loudness (LOUD), fader
(FAD) , balance ( BAL)
and automatic volume
correction settings.
Exit from audio mode is automatic
after a few seconds without pressing
any button, or by pressing button H
after coniguration of the automatic
volume correction.
Note: bass, treble and loudness set-
tings are speciic to each source. It
is possible to set them differently for
radio, cassette (RB3), CD (RD3) and
CD changer. When
"BASS" is dis-
played, press button I
or J to vary the setting.
- "BASS -9" for a min-
imum bass setting,
-
"BASS 0" for a normal
setting,
- "BASS +9" for a maxi-
mum bass setting.

15-03-200415-03-2004
3435YOUR 307 SW IN DETAILRADIO
Notes on radio reception
Your car radio is subject to phenom-
ena which do not affect domestic
radio sets. Both AM (MW/LW) and
FM reception are subject to various
forms of interference. This is no re-
lection on the quality of the equip-
ment, but is due to the nature of the
signals and the way in which they are
transmitted.
On MW/LW, interference may be
noticed when passing under high
voltage power lines or bridges, or in
tunnels.
On FM, interference may be the result
of increasing distance from the trans-
mitter, delection of the signals by
obstacles (mountains, hills, buildings,
etc.), or of being in an area which is
not covered by a transmitter. Selecting radio mode
Selecting a waveband
Adjusting the front/rear sound
distribution (Fader)
When
"FAD" is displayed, press but-
ton I or J.
Button I increases the volume in the
front.
Button J increases the volume in the
rear.
Adjusting the right/left sound
distribution (Balance)
When "BAL" is displayed, press but-
ton I or J.
Button I increases the volume on the
right-hand side.
Button J increases the volume on the
left-hand side.
Automatic volume correction
This function enables the volume to
be automatically adjusted depending
on the level of noise produced by the
speed of the vehicle.
Press buttons I or J to switch the
function on or off. Audio RB3:
press the
"SRC" button
several times in succession.
Audio RD3:
press button R.
Audio RB3:
briely press the "BND/
AST" button to select
the FM1, FM2, FMast
and AM wavebands.
Audio RD3:
briely press button R
to select the FM1, FM2,
FMast and AM wave-
bands.

15-03-200415-03-2004
3435YOUR 307 SW IN DETAILRADIO
Notes on radio reception
Your car radio is subject to phenom-
ena which do not affect domestic
radio sets. Both AM (MW/LW) and
FM reception are subject to various
forms of interference. This is no re-
lection on the quality of the equip-
ment, but is due to the nature of the
signals and the way in which they are
transmitted.
On MW/LW, interference may be
noticed when passing under high
voltage power lines or bridges, or in
tunnels.
On FM, interference may be the result
of increasing distance from the trans-
mitter, delection of the signals by
obstacles (mountains, hills, buildings,
etc.), or of being in an area which is
not covered by a transmitter. Selecting radio mode
Selecting a waveband
Adjusting the front/rear sound
distribution (Fader)
When
"FAD" is displayed, press but-
ton I or J.
Button I increases the volume in the
front.
Button J increases the volume in the
rear.
Adjusting the right/left sound
distribution (Balance)
When "BAL" is displayed, press but-
ton I or J.
Button I increases the volume on the
right-hand side.
Button J increases the volume on the
left-hand side.
Automatic volume correction
This function enables the volume to
be automatically adjusted depending
on the level of noise produced by the
speed of the vehicle.
Press buttons I or J to switch the
function on or off. Audio RB3:
press the
"SRC" button
several times in succession.
Audio RD3:
press button R.
Audio RB3:
briely press the "BND/
AST" button to select
the FM1, FM2, FMast
and AM wavebands.
Audio RD3:
briely press button R
to select the FM1, FM2,
FMast and AM wave-
bands.

15-03-200415-03-2004
3637YOUR 307 SW IN DETAIL
Manual station search
Press the "MAN" button.
Briely press button L or N to in-
crease or decrease the frequency
displayed.
By continuing to press the button
in the direction selected, you will
obtain continuous scrolling of the
frequency.
The scrolling stops as soon as the
button is released.
Pressing the "MAN" button again
returns you to automatic station
search. Automatic storing of FM stations
in the memory (autostore)
Your radio automatically stores the
6 stations with the strongest signal in
FM
. These stations are stored in the
FMast waveband.
If it is not possible to ind 6 stations,
the remaining memories are empty.
Automatic station search
Manual storing of stations in the
memory
Select the station required.
Press one of the buttons "1" to "6"
for more than two seconds.
The sound stops then becomes audi-
ble again, conirming that the station
has been stored in the memory. Audio RB3:
press and hold the
"BND/AST"
button for
more than two seconds.
Audio RD3:
press and hold button
R for more than two
seconds.
Recalling stations stored in the
memory
For each waveband, briely press
buttons "1" to "6" to recall the cor-
responding station.
Briely press button
L or N to search
for the station immediately above or
below. By continuing to press the
button in the direction selected, you
will obtain continuous scrolling of the
frequency.
The scrolling stops at the irst sta-
tion found as soon as the button is
released.
If the TA trafic programme is select-
ed, only stations broadcasting this
type of programme are selected.
Searching for a station occurs irst
in "LO" sensitivity (selection of the
most powerful transmitters) during
scanning of the waveband, then in
"DX" sensitivity (selection of the
weakest and most distant transmit-
ters).
To make a direct search in "DX" sen-
sitivity, press button L or N twice.

15-03-200415-03-2004
3637YOUR 307 SW IN DETAIL
RDS
Using the RDS (Radio Data
System) function on FM
Radio Data System allows you to
continue listening to the same sta-
tion, whatever frequency it is using
for the region you are going through. Trafic information
programme
Regional following mode
When they are part of a network,
certain stations broadcast regional
programmes in the various areas
they serve. With regional following
mode you can keep listening to the
same programme.
Press the
"RDS" button for more
than two seconds to switch the func-
tion on or off.
RDS station following
The display indicates the name of the
station selected. The radio is contin-
ually searching for the station which
has the best reception and which is
transmitting the same programme. Press the
"TA" button
to switch the function
on or off.
The multi-function dis-
play will show:
- "TA" if the function is selected,
- "(TA)" if the function is selected
but not available.
Any trafic information lash will be
given priority, whatever source you
are listening to (radio, cassette or
CD changer).
If you wish to interrupt a message,
press the "TA" button; this switches
the function off.
Note: the volume of trafic informa-
tion announcements is indepen-
dent of the volume of normal radio
listening. You can adjust it using
the volume button. The setting will
be stored and will be used when
the next messages are broadcast.
Briely press the
"RDS"
button to switch the
function on or off.
The multi-function dis-
play will show:
- "RDS" if the function is selected.
- "(RDS)" if the function is selected
but not available.

15-03-200415-03-2004
3839YOUR 307 SW IN DETAIL
CASSETTE: AUDIO RB3
Selecting cassette mode
Fast forward/rewind
Fully press button F or G to fast for-
ward or rewind the cassette. At the
end of the fast forward/rewind, the
set plays the current side. Recommendations for using
casssettes
- Use good quality cassettes.
- Avoid the use of cassettes which
play for longer than 90 minutes.
- Never expose the cassettes to heat or the direct rays of the sun.
- Re-tighten the tape if necessary before inserting the cassette into
the player.
- Clean the playing head regularly with a damp-type cleaning cassette.
When a cassette is
inserted, the cassette
player will start auto-
matically.
If a cassette is already
inserted, press the "SRC" button un-
til cassette mode is selected.
Note: before inserting the cassette,
ensure that the tape is taut.
Ejecting the cassette Direction of play
The player will play sides 1 and 2 of
the cassette alternately, by automati-
cally reversing the direction of play at
the end of a side.
To manually reverse the direction of
play, press buttons
F and G half-way.
Fully press buttons F
and G to eject the cas-
sette from the player.

15-03-200415-03-2004
4041YOUR 307 SW IN DETAIL
Selecting a trackShufle (RDM)
When the CD changer is selected:
- audio RB3: press and hold the
"SRC" button for two seconds;
- audio RD3: press and hold button
P for two seconds.
The tracks will be played in random
sequence. Pressing the button again
for two seconds returns you to nor-
mal play.
CD CHANGER
Selecting CD changer mode
Audio RB3:
press the "SRC" button
several times in succession.
Audio RD3:
press button P. Selecting a disc
Press buttons
"1" to "5" on the radio
to select the corresponding disc. Accelerated play
Press and hold button
L or N for for-
wards or backwards accelerated play.
Accelerated play stops as soon as
the button is released.
Press button L to select the next
track.
Press button N to return to the start
of the current track or to select the
previous track.

15-03-200415-03-2004
3233YOUR 307 SW IN DETAIL
AUDIO RD3
Stalk movement Function
1 - Press (behind) Increase volume.
2 - Press (behind) Decrease volume.
1 + 2 - Simultaneous press Sound cut-off (mute); restoring of the sound b y pressing any button.
3 - Press Automatic search of higher frequencies (radio) -
Selection of the next track (CD).
4 - Press Automatic search of lower frequencies (radio) -
Selection of the previous track (CD).
5 - Press the end Change of source (radio/CD/CD changer).
6 - Rotation
(clockwise) Selection of next station stored in the memory (radio) -
Selection of following CD.
7 - Rotation
(anti-clockwise) Selection of previous station stored in the memory (radio) -
Selection of previous CD.

15-03-200415-03-2004
3233YOUR 307 SW IN DETAIL
ButtonFunction
A Radio on/off.
B - Decrease volume.
C + Increase volume.
D RDS RDS function on/off.
Press for more than 2 seconds: regional following mode on/off.
E TA Trafic information priority on/off.
Press for more than 2 seconds: PTY function on/off.
H
¯Selection of bass, treble, loudness, sound distribution and a utomatic volume correction.
I 5Increase setting of functions associated with button
H.
J 6Decrease setting of functions associated with button
H.
L 8Manual and automatic search of higher frequency.
Selection of next CD track and PTY (radio).
M MAN Manual/automatic operation of buttons L and N.
N 7Manual and automatic search of lower frequency.
Selection of previous CD track and PTY (radio).
P CH.CD Selection of the CD changer.
Press for more than 2 seconds: shufle.
Q CD Selection of the CD.
Press for more than 2 seconds: shufle.
R Radio Selection of the radio. Selection of FM1, FM2, FMast, AM waveba
nds.
Press for more than 2 seconds: automatic storing of stations in the memory (autostore).
S 5
Ejection of the CD.
1 to 6 1 2 3 4 5 6 Selection of station stored in the memory.
Press for more than 2 seconds: storing of a station in the memory.
1 to 5 1 2 3 4 5 Selection of a CD changer disc.