warning light Peugeot 607 Dag 2002 User Guide

INSTRUMENTS AND CONTROLS33
Tyre underinflation warning light
Display of this warning light is acompanied by an audible si
gnal and the message 'Tyre(s) pressure low' on the
multifunction display.
Have the tyre pressure checked as soon as possible.
Low coolant level warning light
Display of this warning light is accompanied by an audible si gnal and the message 'Cooling circuit level low' on
the multifunction display .
Stop immediately.
Warning: wait for the engine to cool before topping up.
The cooling system is pressurised.
In the event of breakdown and to prevent the risk of scalding , unscrew the cap by two turns to allow the pressure to drop.
When the pressure has dropped, remove the cap and top up the level.
Contact a PEUGEOT dealer.
Seat belt not fastened warning light
Display of this warning light is accompanied by an audible si gnal and the message 'Seat belt not fastened' on the
multifunction display.
With the engine running, the warning light comes on when the driver's seat belt is unfastened.
Electronic immobiliser warning light
Display of this warning light is accompanied by an audible si gnal and the message 'Electronic theft protection
faulty' on the multifunction display.
It indicates a malfunction of the electronic immobiliser system.
Contact a PEUGEOT dealer.

INSTRUMENTS AND CONTROLS
34
Water in diesel filter warning light (according to country
)
Display of this warning light is accompanied by an audible si gnal and the message 'Water in diesel filter' on the
multifunction display.
There is a risk of damage to the injection system.
Contact a PEUGEOT dealer as soon as possible.
Front brake pad wear warning light
Display of this warning light is accompanied by an audible si gnal and the message 'Brake pads worn'on the multi
function display.
For your safety, have the pads replaced by a PEUGEOT dealer as soon as the warning light comes on.
Low fuel level warning light
Display of this warning light is accompanied by an audible si gnal and the message 'Fuel level low'on the multi
function display.
When the warning light comes on, you have enough fuel to drive approximately 30 miles (50 km). The tank capac
ity is approximately 80 litres.
Fuel cap warning light
Display of this warning light is accompanied by an audible si gnal and the message 'Fuel cap open'on the multi
function display.
It comes on if the fuel tank cap is not correctly screwed on or is missing.
Door/bonnet/boot open warning light
Display of this warning light with the engine running is accompanied by an audible signal and an illustration on th e
multifunction display, showing which opening has not been correctly closed.
Air bag warning light
Display of this warning light is accompanied by an audible si gnal and the message 'Air bag faulty'on the multi
function display.
Contact your PEUGEOT dealer.

INSTRUMENTS AND CONTROLS35
Engine diagnostics warning light
This is linked to the warning light on the instrument pane
l.
Display of this warning light is accompanied by an audible si gnal and the message 'Engine emission control sys
tem faulty' on the multifunction display.
If it flashes when the engine is running, this indicates a malfunction in the injection, ignition or emission control system. There
is a risk of damage to the catalytic converter (petrol engine onl y).
Contact a PEUGEOT dealer as soon as possible.
Bulb blown warning light
Display of this indicator light is accompanied by an audible signal and the message 'Bulb... faulty' on the multifunc
tion display, indicating the faulty bulb: a bulb in th e dipped beam lights, the side lights, the direction indi cator lights
(except side repeaters) or the brake lights (except the central brake light).
Change the faulty bulb.
Windscreen/headlamp wash reservoir warning light
Display of this warning light is accompanied by an audible si gnal and the message 'Screenwash low'on the multi
function display.
Fill the windscreen/headlamp wash reservoir the next time you st op.
Particulate emission filter saturation warning light (diesel engine)
Display of this warning light is accompanied by an audible si gnal.
When it occurs with the engine running, this indicates the start of saturation of the particulate emission filter (excep
tionally long periods of town type driving conditions: reduce d speed, long tailbacks...).
To regenerate the filter, you are advised to drive as soon as possible and when traffic conditions permit at a speed of 35 mph
(60 km/h) or more for at least five minutes (until the warning li ght goes out).
If the light remains on, contact a PEUGEOT dealer.
Note: After prolonged operation of the vehicle at a very low speed or at idle, you may sometimes notice steam coming from
the exhaust during acceleration. This has no effect on the p erformance of the vehicle or on the environment.

INSTRUMENTS AND CONTROLS
36
Antilock braking system (ABS) warning light
This is linked to the warning light on the instrument pane
l.
Display of this warning light is accompanied by an audible si gnal and the message 'ABS faulty' on the multifunc
tion display.
If the warning light remains on, or comes on at over 8 mph (12 km/h), this indicates a malfunction of the ABS.
However, the vehicle retains conventional servoassisted braking.
Contact a PEUGEOT dealer.
Automatic headlamp adjustment warning light
Display of this warning light is accompanied by an audible si gnal and the message 'Automatic adjustment of
headlamps faulty' on the multifunction display.
It comes on if there is a malfunction of the system.
Contact a PEUGEOT dealer. Automatic gearbox fault warning light
Display of this warning light is accompanied by an audible si gnal and the message 'Automatic gearbox faulty' on
the multifunction display.
It comes on if there is an abnormality in the automatic gearbo x.
The gearbox will continue to operate in downgrade mode (lo cked in 3rd gear).
Contact a PEUGEOT dealer. Tyre underinflation detector battery flat / remote control ba ttery flat / impact sensor fault / wheel(s) miss
ing warning light
Display of this warning light is accompanied by an audible si gnal and a message on the multifunction display show
ing the cause of the warning:
– 'Tyre pressure sensor battery charge low',
– 'Remote control battery charge low',
– 'Impact sensor faulty',
– 'X tyre pressure sensor(s) missing'.
Contact a PEUGEOT dealer.

INSTRUMENTS AND CONTROLS
40
Coolant temperature indicator
When the needle is in
zone A, the
temperature is correct.
When the needle is in zone B, the
temperature is too high.
In cases where the coolant tem
perature warning light comes on
(linked to the STOPwarning light),
you must stop immediately.
Warning: wait for the engine to cool
down.
If necessary, top up the level.
Because the cooling system is pres
surised, to prevent the risk of scald
ing, turn the cap two turns to allow
the pressure to drop.
When the pressure has dropped,
remove the cap and top up the level.
Contact a PEUGEOT dealer.Engine oil level and
temperature
When the ignition is switched on, this
gauge indicates the engine oil level
for approximately 20 seconds, then it
indicates the engine oil temperature.
Engine oil level
The reading is valid only if the vehi
cle is on level ground, and the
engine has been switched off for 10
minutes.
With the ignition on, wait for the
graduated sector to light up and the
indicator needle to move.
When the needle is in zone C, the oil
level is correct.
When the needle is in zone D, the oil
level is incorrect.
There is a risk of damage to the
engine.
 Check the level with the dipstick.
You must top up the level without
exceeding the maximum level on
the gauge.
Engine oil temperature
When the needle is in zone E, the
temperature is correct.
When the needle is in zone F, the
temperature is too high.
Reduce your speed to lower the
temperature.
Service indicator and total
distance recorder
When the ignition is switched on, this
indicates servicing information for a
few seconds, then the total and trip
distances.
Service function
See the 'Service indicator' section.
Total distance recorder function
The total distance is displayed on the
left side of the screen and the trip
distance on the right side.

Changing the colours
Select the desired colour, then confirm.
If required, select 'automatic
day/night' , then confirm and record
the changes.
Note: this function allows the system
to change automatically to 'Night'
colour when the vehicle lights are on.
Changing the brightness
Select the 'Brightness' function,
then confirm:
– turn the dial clockwise to increase,
– turn the dial anticlockwise to decrease.
Record the modifications.
Note: this function allows only limit
ed adjustment of the brightness,
since the screen lighting is depen
dent on the sunshine/brightness sen
sor in the vehicle.
YOUR 607 IN DETAIL 45
Insert the software CDRom into the
drive in place of the map CDRom.
After a few moments, the mesage
"Warning Reprogramming Sequence"
then the message "Navigation applica
tion Processing" apears, together with
a progress bar.
When the message "Software Loading
End Eject CD" appears, eject the
software CDRom and insert the map
CDRom into the drive.
Check that the CDRom has loaded
correctly (see paragraph "Voice syn
thesis adjustment" in the chapter enti
tled "The satellite navigation system
with colour screen").

YOUR 607 IN DETAIL
100
SEAT BELTS
Front seat belt height adjustment:
 To lower the attachment point,
squeeze control 1and slide it
downwards.
 To raise the attachment point,
squeeze control 1and slide it
upwards.
To lock the seat belts  Pull the strap, then insert the end
into the buckle. Front seat belts with
pretensioner and force limiter
Safety in the event of a frontal impact
has been improved by the introduc
tion of seat belts with pretensioner
and force limiter connected to the
front air bags. Depending on the
seriousness of the impact, the pre
tensioning system instantly tightens
the seat belts firmly against the bod
ies of the occupants.
The pretensioning seat belts are
armed when the ignition is on.
The force limiter reduces the pres
sure of the seat belt on the body of
the occupant in the event of an acci
dent.
Rear seat belts with force limiter
The rear seats are all fitted with a
threepoint inertia reel seat belt.
Third rear central seat belt
– pull the belt located between the
two head restraints at the left rear,
– insert the fixed buckle in the black clasp located on the left,
– insert the sliding buckle in the red and black (movable) clasp. To
release it, press the black button of
the locking clasp.
To be effective, a seat
belt must be tightened as
close to the body as pos
sible.
Depending on the nature and seri
ousness of the impact, the pre
tensioners may be triggered
before and independently of the
air bags.
In all cases, the air bag warning
light comes on.
After an impact, have the system
checked by a PEUGEOT dealer.
The system has been designed to
be fully oper ational for ten years.
Have it replaced after this period.

Electronic engine immobiliser
This locks the engine control system
a few moments after the ignition has
been switched off and therefore pre
vents starting of the vehicle by any
one who does not have the key.
The ignition key has an electronic
chip which has a special code. When
the ignition is switched on, the code
is recognised and starting is possi
ble.
If the system does not function
correctly, the central locking button
indicator light, situated on the centre
console, flashes rapidly when the
ignition is switched on (2nd notch).
WARNING: your vehicle is no longer
protected in this event.
Contact a PEUGEOT dealer as soon
as possible. Flat battery
(CR 2025/3 volt battery)
This is indicated by illumination of a
warning light on the instrument panel
display, accompanied by an audible
signal and a message on the multi
function display.
Contact a PEUGEOT dealer to
replace the battery.
YOUR 607 IN DETAIL
102
Key in ignition
A buzzer sounds on opening the dri
ver's door, if the key has been left in
the ignition. Locating your car
To locate your car in a car park:
 press button A; the courtesy lights
come on and the direction indica
tors flash for a few seconds.
Programming the
remote control
in the key  Switch off the ignition.
 Switch the ignition on again.
 Immediately press button A.
 Switch off the ignition and remove
the remote control key from the
ignition lock. The remote control
key is now working again.
Confidential card
The confidential card contains the
identification code necessary for any
work carried out by a PEUGEOT
dealer on the system. This code is
hidden by a film which should be
removed only if necessary.
Keep your card in a safe place,
never inside the vehicle.

Electronic engine immobiliser
This locks the engine control system
a few moments after the ignition has
been switched off and therefore pre
vents starting of the vehicle by any
one who does not have the key.
The ignition key has an electronic
chip which has a special code. When
the ignition is switched on, the code
is recognised and starting is possi
ble.
If the system does not function
correctly, the central locking button
indicator light, situated on the centre
console, flashes rapidly when the
ignition is switched on (2nd notch).
WARNING: your vehicle is no longer
protected in this event.
Contact a PEUGEOT dealer as soon
as possible. Flat battery
(CR 2025/3 volt battery)
This is indicated by illumination of a
warning light on the instrument panel
display, accompanied by an audible
signal and a message on the multi
function display.
Contact a PEUGEOT dealer to
replace the battery.
YOUR 607 IN DETAIL
102
Key in ignition
A buzzer sounds on opening the dri
ver's door, if the key has been left in
the ignition. Locating your car
To locate your car in a car park:
 press button A; the courtesy lights
come on and the direction indica
tors flash for a few seconds.
Programming the
remote control
in the key  Switch off the ignition.
 Switch the ignition on again.
 Immediately press button A.
 Switch off the ignition and remove
the remote control key from the
ignition lock. The remote control
key is now working again.
Confidential card
The confidential card contains the
identification code necessary for any
work carried out by a PEUGEOT
dealer on the system. This code is
hidden by a film which should be
removed only if necessary.
Keep your card in a safe place,
never inside the vehicle.

THE ALARM
This provides two types of protec
tion, exterior and interior:
– exterior protection: when this is set, the alarm sounds if a door, the
boot or the bonnet is opened.
– interior protection: when this is set, the alarm sounds if the sensors
detect a variation in the air move
ment inside the vehicle (breaking
of a window or a movement inside
the vehicle).
Setting the alarm
Switch off the ignition and get out
of the vehicle.
Set the alarm within five minutes
of getting out of the vehicle, by
locking or deadlocking using the
remote control (button Bindicator
light flashes once per second). Note:
if you wish to lock your vehicle
without setting the alarm, use the
door lock.
When the alarm is triggered, the
siren sounds and the direction indi
cators flash for thirty seconds.
It then stops, but the alarm remains
set.
Warning: if the alarm has been trig
gered ten times in succession, on
the eleventh time it becomes inac
tive.
Note: if button B flashes rapidly, the
alarm has been triggered while you
were away from your vehicle.
Automatic activation
The alarm is activated automatically
two minutes after the door or boot
were last closed.
In order to avoid accidental trigger
ing of the alarm when a door or the
boot is opened, it is essential to
press the remote control opening
button first.
Disarming
Unlock the vehicle with the remote
control key (button Bindicator light
goes out).
Note: if the alarm has been triggered
while you were away from your car,
the rapid flashing of the indicator
light will stop when you switch on the
ignition. To set the alarm with exterior
protection only
If, while you are away from the vehi
cle, you wish to leave a window par
tially open or a pet inside the vehicle,
you should choose exterior protec
tion only.
Switch off the ignition
In the next ten seconds, press
button
Auntil indicator light B is
on continuously.
Get out of the vehicle.
Set the alarm by locking or dead
locking using the remote control
switch ( button Bindicator light
flashes once a second).
Note: when the alarm is set but the
remote control does not operate:
Unlock the doors with the key and
open the door. The alarm is trig
gered.
Switch on the ignition in the next
ten seconds. The alarm is disar
med.
Incorrect operation
When the ignition is switched on, if
button Blights for ten seconds, there
is a fault in the siren connection.
Contact a PEUGEOT dealer to have
the system checked.
YOUR 607 IN DETAIL
104