intelligent key system RENAULT PULSE 2012 1.G Owner's Guide

Page 196 of 352


> (GLW    0RGHO .$ 2(0 B5HQDXOW @
5-10Starting and driving
.If it becomes necessary to start the engine
with a booster battery and jumper cables,
the instructions and cautions contained in
the “6. In case of emergency” section should
be carefully followed.
7. Allow the engine to idle for \ft le\fst 30 seconds \ffter st\frting the engine to w\fr\b-up. Drive \ft
\boder\fte speeds for \f short dist\fnce first,
especi\flly in cold we\fther.
CAUTION:
Do not leave the vehicle unattended while the
engine is warming up.
GASOLINE ENGINE
1. Apply the p\frking br\fke.
2.Automatic Transmission (AT)/Continuously
Variable Transmission (CVT) model:
Move the selector lever to the “P” (P\frk) or the “N”
(Neutr\fl) position.
The starter is designed to operate only when
the selector lever is in the proper position.
Manual Transmission (MT) model:
Move the shift lever to the “N” (Neutr\fl) position.
The starter is designed to not operate unless
the clutch pedal is fully depressed.
The Intelligent Key must be carried when
operating the ignition switch.
3. Push the ignition switch to the “ON” position. Depress the br\fke ped\fl (AT/CVT \bodel) or the
clutch ped\fl (MT \bodel) \fnd push the ignition
switch to st\frt the engine.
To st\frt the engine i\b\bedi\ftely, push \fnd rele\fse
the ignition switch while depressing the br\fke
ped\fl or clutch ped\fl with the ignition switch in
\fny position.
4. I\b\bedi\ftely rele\fse the ignition switch when the engine st\frts. If the engine st\frts, but f\fils to run,
repe\ft the \fbove procedures.
If the engine is very h\frd to st\frt in extre\bely cold
or hot we\fther, depress the \fcceler\ftor ped\fl \fnd
hold it. Push the ignition switch for up to 15
seconds while holding. Rele\fse the \fcceler\ftor
ped\fl when the engine st\frts.CAUTION:
.As soon as the engine has started, release
the ignition switch immediately.
. Do not operate the starter for more than 15
seconds at a time. If the engine does not
start, push the ignition switch to the “OFF”
position and wait 10 seconds before crank-
ing the engine again. Otherwise, the starter
could be damaged.
. If it becomes necessary to start the engine
with a booster battery and jumper cables,
the instructions and cautions contained in
the “6. In case of emergency” section should
be carefully followed.
5. Allow the engine to idle for \ft le\fst 30 seconds \ffter st\frting the engine to w\fr\b-up. Drive \ft
\boder\fte speeds for \f short dist\fnce first,
especi\flly in cold we\fther.
CAUTION:
Do not leave the vehicle unattended while the
engine is warming up.
6. To stop the engine, \bove the selector lever to the“P” (P\frk) position (AT/CVT \bodel) or \bove the
shift lever to the “N” (Neutr\fl) position (MT \bodel) ,
\fpply the p\frking br\fke \fnd push the ignition
switch to the “OFF” position.
STARTING ENGINE (model with
Intelligent Key system)
&RQGLWLRQ

Page 200 of 352


> (GLW    0RGHO .$ 2(0 B5HQDXOW @
5-14Starting and driving
JVS0014XRight-Hand Drive (RHD) modelTo release the shi\ft lock, \ber\form the \following
\brocedure
1. Models with Intelligent KEY system: Place theignition switch in the “OFF” or “LOCK” \bosition.
Models without Intelligent KEY system: Place the
ignition switch in the “LOCK” \bosition and remove
the key.
2. A\b\bly the \barking brake.
3. De\bress the shi\ft lock release button.
4. Push and hold the selector lever button and move the selector lever to the “N” (Neutral) \bosition
while holding down the shi\ft lock release button.
5. Place the ignition switch to the “ON” \bosition to release the steering wheel lock.
The vehicle may be moved, by \bushing, to the desired
location.
I\f the selector lever cannot be moved out o\f the “P”
(Park) \bosition, have a RENAULT dealer check the AT
system as soon as \bossible.
Fail-sa\fe
When the \fail-sa\fe o\beration occurs, the AT will be
locked in third gear.
If the vehicle is driven under extreme conditions,
such as excessive wheel spinning and subse-
quent hard braking, the fail-safe system may be
activated. This will occur even if all electrical
circuits are functioning properly. In this case,
turn the ignition switch off and wait for 3
seconds. Then turn the ignition switch back to
the “ON” position. The vehicle should return to
its normal operating condition. If it does not
return to its normal operating condition, have a
RENAULT dealer check the transmission and
repair it if necessary.
DRIVING WITH CONTINUOUSLY VARI-
ABLE TRANSMISSION (CVT)
The Continuously Variable Transmission (CVT) in your
vehicle is electronically controlled to \broduce maximum
\bower and smooth o\beration.
The recommended o\berating \brocedures \for this
transmission are shown on the \following \bages. Follow
these \brocedures \for maximum vehicle \ber\formance
and driving enjoyment.
WARNING:
Do not downshift abruptly on slippery roads.
This may cause a loss of control.
CAUTION:
. The cold engine idle speed is high, so use
caution when shifting the transmission into
a forward or reverse position before the
engine has warmed up. .
Avoid revving up the engine while the
vehicle is stopped. This could cause unex-
pected vehicle movement.
. Never shift to either the “P” (Park) or “R”
(Reverse) position while the vehicle is mov-
ing. This could cause serious damage to the
transmission.
. Start the engine in either the “P” (Park) or
“N” (Neutral) position. The engine will not
start in any other position. If it does, have
your vehicle checked by a RENAULT dealer.
. Shift into the “P” (Park) position and apply
the parking brake when at a standstill for
longer than a short waiting period.
. Keep the engine at idling speed while
shifting from the “N” (Neutral) position to
any driving position.
. When stopping the vehicle on an uphill
grade, do not hold the vehicle by depressing
the accelerator pedal. The foot brake pedal
should be depressed in this situation.
Starting vehicle
1. A\fter starting the engine, \fully de\bress the \foot
brake \bedal be\fore moving the selector lever out
o\f the “P” (Park) \bosition.
2. Kee\b the \foot brake \bedal de\bressed and move the selector lever to a driving \bosition.
3. Release the \barking brake, the \foot brake \bedal, and then gradually start the vehicle in motion.
The CVT is designed so the foot brake pedal
MUST be depressed before shifting from the “P”
(Park) position to any driving position while the
ignition switch is in the “ON”position.
&RQGLWLRQ

Page 202 of 352


> (GLW    0RGHO .$ 2(0 B5HQDXOW @
5-16Starting and driving
P (Park):
Use this position when the vehicle is par\fed or when
starting the engine.Make sure that the vehicle is
completely stopped and move the selector lever
into the \bP”(Park) position. Apply the par\fing
bra\fe. When par\fing on a hill, first depress the foot
bra\fe pedal, apply the par\fing bra\fe, and then move
the selector lever into the \bP” (Par\f) position.
R (Reverse):
Use this position to bac\f up. Ma\fe sure that the vehicle
is completely stopped before selecting the \bR”
(Reverse) position.
N (Neutral):
Neither the forward nor reverse gear is engaged. The
engine can be started in this position. You may shift to
the \bN” (Neutral) position and restart a stalled engine
while the vehicle is moving.
D (Drive):
Use this position for all normal forward driving.
L (Low):
Use this position when climbing steep hills slowly or
driving slowly through deep snow, sand or mud, or for
maximum engine bra\fing on steep downhill grades.SPORT mode switch
JVC0027XRight-Hand Drive (RHD) modelTo select the SPORT mode, push the SPORT mode
switch with the selector lever in the \bD” (Drive)
position. The SPORT mode indicator light
in the
meter panel illuminates. To turn off the SPORT mode,
push the SPORT mode switch again. The SPORT
mode indicator light will turn off. When the selector
lever is shifted to any position other than \bD”, the
SPORT mode will be automatically turned off.
“OFF” position:
For normal driving and fuel economy, use the \bOFF”
position.
“ON” position:
For driving up or down long slopes where engine
bra\fing is necessary, or for powerful acceleration, use
the \bON” position. The transmission will automatically
select a different gear ratio, allowing the engine to
provide high output.
When driving conditions change, push the switch to
turn the SPORT mode off.
Remember not to drive at high speeds for extended
periods of time with the SPORT mode in the \bON”
position. This reduces fuel economy.
Accelerator downshift - in the \bD” position -
For passing or climbing hills, depress the accelerator
pedal to the floor. This shifts the transmission down
into a lower gear, depending on the vehicle speed.
Shift loc\f release
JVC0028XRight-Hand Drive (RHD) modelIf the battery charge is low or discharged, the selector
lever may not be moved from the \bP” (Par\f) position
even with the bra\fe pedal depressed and the selector
lever button pushed.
To move the selector lever, perform the following
procedure:
1. Model with Intelligent Key system:
Place the ignition switch in the \bOFF” or \bLOCK”
position.
Model without Intelligent Key system:
Place the ignition switch in the \bLOCK” position,
and remove the \fey if it is inserted.
2. Apply the par\fing bra\fe.
3. Depress the shift loc\f release button.
4. Push the selector lever button and move the selector lever to the \bN” (Neutral) position while
holding down the shift loc\f release.
&RQGLWLRQ

Page 203 of 352


> (GLW    0RGHO .$ 2(0 B5HQDXOW @
5. Place the ignition switch in the “ON” \fosition tounlock the steering wheel.
\bhe vehicle may be moved to the desired location.
Re\flace the removed shift lock release cover after the
o\feration.
For model with Intelligent Key system: If the battery is
discharged com\fletely, the steering wheel cannot be
unlocked. Do not move the vehicle with the steering
wheel locked.
If the selector lever cannot be moved out of the “P”
(Park) \fosition, have a RENAUL\b dealer check the
CV\b system as soon as \fossible.
WARNING:
If the selector lever cannot be moved from the
“P” (Park) position while the engine is running
and the brake pedal is depressed, the stop lights
may not work. Malfunctioning stop lights could
cause an accident injuring yourself and others.
High fluid tem\ferature \frotection mode
\bhis transmission has a high fluid tem\ferature \frotec-
tion mode. If the fluid tem\ferature becomes too high
(for exam\fle, when climbing stee\f grades in high
tem\ferature with heavy loads, such as when towing a
trailer) , engine \fower and, under some conditions,
vehicle s\feed will be decreased automatically to
reduce the chance of transmission damage. Vehicle
s\feed can be controlled with the accelerator \fedal,
but engine and vehicle s\feed may be limited.
Fail-safe
When the fail-safe o\feration occurs, the CV\b will not
be shifted to the selected driving \fosition.
If the vehicle is driven under extreme conditions,
such as excessive wheel spinning and subse-
quent hard braking, the fail-safe system may be
activated. This will occur even if all electrical
circuits are functioning properly. In this case,
place the ignition switch in the “OFF”position
and wait for 10 seconds. Then turn the ignition
switch back to the “ON”position. The vehicle
should return to its normal operating condition.
If it does not return to its normal operating
condition, have a RENAULT dealer check the
transmission and repair it if necessary.
WARNING:
When the fail-safe operation occurs, vehicle
speed may be gradually reduced. The reduced
speed may be lower than other traffic, which
could increase the chance of a collision. Be
especially careful when driving. If necessary, pull
to the side of the road at a safe place and allow
the transmission to return to normal operation,
or have it repaired if necessary.
DRIVING WI\bH MANUAL \bRANSMISSION
(M\b)
WARNING:
. Do not downshift abruptly on slippery roads.
This may cause a loss of vehicle control.
. Do not over-rev the engine when shifting to
a lower gear. This may cause a loss of
vehicle control or engine damage.
CAUTION:
.Do not rest your foot on the clutch pedal
while driving. This may damage the clutch
system.
. Fully depress the clutch pedal before shift-
ing to help prevent transmission damage.
. Stop the vehicle completely before shifting
into the “R” (Reverse) position.
. When the vehicle is stopped for a period of
time, for example waiting at stoplights, shift
to the “N” (Neutral) position and release the
clutch pedal with the foot brake pedal
depressed.
. Do not shift to the "N" (Neutral) position
while driving. Doing so may result in an
accident due to loss of engine braking.
Starting and driving5-17
&RQGLWLRQ

Page 207 of 352


> (GLW    0RGHO .$ 2(0 B5HQDXOW @
The Stop/Start System is designed to prevent
unne\fessary fuel \fonsumption, e\bhaust emissions,
and noise during a journey:
.When the vehi\fle \fomes to rest the engine is
automati\fally stopped.
. The engine is then automati\fally restarted before
you are ready to drive away.
CAUTION:
At the end of the journey the engine must be
stopped and ignition switch be turned off. Lock
the vehicle as normal. Turning the ignition OFF
will shut down all electrical systems. Failure to
do this may result in a flat battery.
NORMAL OPERATION
The Stop/Start System stops the engine and will
automati\fally restart the engine. The Stop/Start
indi\fator light is shown in the meter.
The Stop/Start System will automati\fally stop
the engine when all the following \fonditions
are valid.
For MT model
.The shift lever is in Neutral position.
. The \flut\fh pedal is fully released.
. The vehi\fle speed is below about 2 km/h (1
MPH) .
. The driver’s seat belt is fastened.
. The Intelligent Key is in the vehi\fle.
. The driver’s door is \flosed.
For CVT model
. The sele\ftor lever is in the "D" (Drive) or "N"
(Neutral) position. .
The brake pedal is depressed.
. The vehi\fle is stopped.
. The driver’s seat belt is fastened.
. The driver’s door is \flosed.
NOTE:
The following conditions must also be satisfied
before the engine is automatically stopped. If
the engine does not stop this does not indicate a
malfunction in the system:
. The engine coolant temperature is at normal
operating levels.
. The vehicle has driven some distance since
engine start.
. The battery voltage and temperature are
within normal levels.
. The hood is closed.
. The steering wheel is not being turned.
. The system is not in front defogger mode.
(automatic air conditioner)
. The mode dial is not in front defogger mode.
(manual air conditioner)
. The rear window defogger is not operated.
NOTE:
The engine will not restart if the brake pedal is
released while the Stop/Start System is acti-
vated under the following condition:
. The selector lever is in the "P" (Park) position
(for CVT model) .
When the Stop/Start System indi\fator light is
displayed the engine starts running automa-
ti\fally under at least one of the following
\fonditions.
.The \flut\fh pedal is depressed (for MT model) .
. The brake pedal is released with the sele\ftor lever
in the "D"(Drive) or "N"(Neutral) position (for CVT
model) .
. The sele\ftor lever is pla\fed in the "L"(Low) ,
"D"(Drive) or "R"(Reverse) position from the "N"
or "P" position (for CVT model) .
. The driver’s seat belt is unfastened, or the driver’s
door is open (for CVT model) .
. The brake pedal is repeatedly pressed (to maintain
vehi\fle braking performan\fe) .
. The brake pedal is strongly depressed and then
released with the sele\ftor lever in the "P" (Park)
position, resulting in de\freased va\fuum pressure
of the brake booster (for CVT model) .
. The battery voltage be\fomes low (due to ele\ftri\fal
load from other vehi\fle systems like headlights,
heaters, et\f., or au\biliary devi\fes \fonne\fted to the
12 volt so\fket inside the vehi\fle) .
. The vehi\fle speed is above about 2 km/h (1
MPH) .
. The system is in front defogger mode. (automati\f
air \fonditioner)
. The mode dial is in front defogger mode. (manual
air \fonditioner)
. The rear window defogger is operated.
NOTE:
The following conditions will prevent the Stop/
Start System from automatically restarting the
engine. Starting the engine by the ignition
switch is then necessary:
Starting and driving5-21
STOP/START SYSTEM (if equipped
for Europe)
&RQGLWLRQ

Page 217 of 352


> (GLW    0RGHO .$ 2(0 B5HQDXOW @
quickly become high enough to cause se-
vere or possibly fatal illness to people and
animals.
SSD0488
Left-Hand Drive (LHD) model
SSD0489
Right-Hand Drive (RHD) model1. Firmly apply the par\fing bra\fe.
\b. Automatic Transmission (AT)/Continuously Vari-able Transmission (CVT) model: Move the selector
lever to the “P” (Par\f) position.
Manual Transmission (MT) model: Move the shift
lever to the “R” (Reverse) position. When par\fing
on an uphill grade, move the shift lever to the “1”
(1st) position. 3. To help prevent the vehicle from moving into traffic
when par\fed on an incline, it is a good practice to
turn the wheels as illustrated.
HEADED DOWNHILL WITH CURB
*1
Turn the wheels into the curb and move the vehicle
forward until the curb side wheel gently touches
the curb. Then apply the par\fing bra\fe. HEADED UPHILL WITH CURB
*2
Turn the wheels away from the curb and allow the
vehicle to move bac\f until the curb side wheel
gently touches the curb. Then apply the par\fing
bra\fe.
HEADED UPHILL OR DOWNHILL, WITHOUT
CURB
*3
Turn the wheels toward the side of the road so the
vehicle will move away from the center of the road
if the vehicle moves. Then apply the par\fing bra\fe.
4. Model with Intelligent Key system:
Place the ignition switch in the “OFF” position.
Model without Intelligent Key system:
Place the ignition switch in the “LOCK” position
and remove the \fey.
NOTE:
For Model with Stop/Start (Idling Stop) System:
Use this system when the vehicle is stopped for
a period of time, for example waiting at stop-
lights.
Stop the engine with the ignition switch when
parking, etc. for an extended period of time.
Starting and driving5-31
&RQGLWLRQ

Page 235 of 352


> (GLW    0RGHO .$ 2(0 B5HQDXOW @
1. If the booster battery is in another vehicle*B,
\fosition the two vehicles*Aand*Bto bring the
batteries into close \fro\bimity to each other.
CAUTION:
If the battery of vehicle*Aequipped with the
Intelligent Key system is discharged, the ignition
switch cannot be moved from the “LOCK”
position and, if the steering lock is engaged,
the steering wheel cannot be moved. Connect
the jumper cables to the booster vehicle
*Bbefore turning the ignition switch and disenga-
ging the steering lock.
2. A\f\fly the \farking brake.
3. Automatic Transmission (AT)/Continuously Vari- able Transmission (CVT) model: Move the selector
lever to the “P” (Park) \fosition.
Manual Transmission (MT) model: Move the shift
lever to the “N” (Neutral) \fosition.
4. Switch off all unnecessary electrical systems (headlights, heater, air conditioner, etc.) .
5. Turn the ignition switch to the “LOCK” \fosition.
6. Remove the vent ca\fs, if equi\f\fed, on the battery.
7. Cover the battery with a firmly wrung out moist cloth to reduce the hazard of an e\b\flosion.
8. Connect the jum\fer cables in the sequence as illustrated (
*1,*2,*3,*4).
CAUTION:
.Always connect positive +to positive +and
negative 7to body ground, NOT to the
battery’s negative 7. .
Be sure that the jumper cables do not touch
moving parts in the engine compartment.
. Be sure that the jumper cable’s clamps do
not contact any other metal.
9. Start the engine of the booster vehicle
*Band let
it run for a few minutes.
10. De\fress the accelerator \fedal of the booster vehicle
*Bat about 2,000 r\fm.
11. Start the engine of the jum\fed vehicle
*Ain the
normal manner.
CAUTION:
. Never keep the starter motor engaged for
more than 10 seconds. If the engine does not
start right away, turn the ignition switch
“OFF” and wait at least 10 seconds before
trying again.
. If the starter motor does not start by pushing
the ignition switch, push the ignition switch
to the OFF position before trying again.
12. After the engine is started, carefully disconnect the jum\fer cables in the o\f\fosite sequence from
that illustrated (
*4,*3,*2,*1).
13. Remove and dis\fose of the cloth as it may be contaminated with corrosive acid.
14. Re\flace the vent ca\fs, if removed.
NOTE:
. For model with Stop/Start (Idling Stop)
System, use the special battery that is
enhanced in regard to the charge-discharge
capacity and life performance. Avoid using a
non-special battery for the Stop/Start (Idling
Stop) system, as this may cause early deterioration of the battery or a malfunction
of the Stop/Start (Idling Stop) system. For
the battery, it is recommended to use
Genuine RENAULT parts. For more informa-
tion, contact a RENAULT dealer.
. For model with Stop/Start (Idling Stop)
System, it may take some time until Stop/
Start (Idling Stop) System activates when
the battery is replaced or the battery term-
inal is disconnected for extended periods
and then reconnected.
In case of emergency6-9
&RQGLWLRQ

Page 293 of 352


> (GLW    0RGHO .$ 2(0 B5HQDXOW @
FOR EUROPE
Remote keyless entry system (if e\fuipped\b
Hereby, ALPS ELECTRIC CO.,LTD. declares that
these Keyless and TPMS TUNER; model TWC1G124
and Keyless Transmitter; model TWB1U761 are in
compliance with the essential re\fuirements and other
relevant provisions of Directive 1999/5/EC.
CAUTION:
Do not exposed to excessive heat such as
sunshine, fire or the like.
CAUTION:
Danger of explosion if battery is incorrectly
replaced. Replace only with the same or equiva-
lent type.
Intelligent Key system (if e\fuipped\b
Hereby, ALPS ELECTRIC CO.,LTD. declares that
these Passive Entry System(Hand Unit\b;model
TWB1G662, Passive Entry System(Tuner\b;model
TWC1G135, ANT ASSY-IMMOBILISER;model
TWK1A002 are in compliance with the essential
re\fuirements and other relevant provisions of Directive
1999/5/EC.
CAUTION:
Do not exposed to excessive heat such as
sunshine, fire or the like.
CAUTION:
Danger of explosion if battery is incorrectly
replaced. Replace only with the same or equiva-
lent type.
Anti-Theft System immobilizer
Hereby, CalsonicKansei Corp. declares that this ANT
ASSY-IMMOBILISER;model MW1014 is in compli-
ance with the essential re\fuirements and other
relevant provisions of Directive 1999/5/EC.
CAUTION:
Do not exposed to excessive heat such as
sunshine, fire or the like.
CAUTION:
Danger of explosion if battery is incorrectly
replaced. Replace only with the same or equiva-
lent type.
FOR CROATIA
Remote keyless entry system (if e\fuipped\b
JVT0008X
Technical information9-9
RADIO APPROVAL NUMBER AND
INFORMATION
&RQGLWLRQ

Page 294 of 352


> (GLW    0RGHO .$ 2(0 B5HQDXOW @
9-10Technical information
JVT0009X
Intelligent Key system \fif equi\b\bed)
JVT0010X
JVT0011X
&RQGLWLRQ

Page 295 of 352


> (GLW    0RGHO .$ 2(0 B5HQDXOW @
Anti-Theft System immobilizer
J\fT0012\b
FOR CHINA
Remote keyless entry system (if equipped)
J\fT0005\b
Intelligent Key system (if equipped)
J\fT0006\b
Technical information9-11
&RQGLWLRQ

Page:   < prev 1-10 11-20 21-30 31-40 41-50 next >