RENAULT SCENIC 2008 J84 / 2.G Electrical Equipment - Instrument Panel Owner's Guide

83A-31
MR-372-J84-83A000$567.mif
V8
INSTRUMENT PANEL
Fault finding - Interpretation of statuses83A
TDB ph2 (EG/MG)
Prog Version: 04xx
Vdiag No.: 08, 0C
ET097
PARKING BRAKE
NOTESSpecial notes:
Only apply the checks if the APPLIED and RELEASED statuses are not consistent
with the lever position:
–APPLIED when the lever is released.
–RELEASED when the lever is applied.
STATUS
"APPLIED" when
the lever is
releasedCheck that the handbrake switch is correctly connected and check the condition of the
connections.
Repair if necessary.
With the lever released, check continuity is absent on the following connection:
Handbrake switch track 1 Vehicle earth
If there is continuity, replace the switch.
Check the insulation of the following connection:
Instrument panel track 21 Track 1 of the handbrake switch
If there is a repair method (see Technical note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair) repair the wiring, otherwise replace it.
RELEASED
STATUS when the
lever has been
pulled upCheck that the handbrake switch is correctly connected and check the condition of the
connections.
Repair if necessary.
With the lever pulled up, check continuity on the following connection:
Handbrake switch track 1 Vehicle earth
If there is no continuity, replace the switch.
Check the insulation of the following connection:
Instrument panel track 21 Track 1 of the handbrake switch
If there is a repair method (see Technical note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair) repair the wiring, otherwise replace it.
AFTER REPAIRCarry out another fault finding check on the system.
Deal with any other faults.
Clear the stored faults.
TDB_V08_ET097/TDB_V0C_ET097

83A-32
MR-372-J84-83A000$567.mif
V8
INSTRUMENT PANEL
Fault finding - Interpretation of statuses83A
TDB ph2 (EG/MG)
Prog Version: 04xx
Vdiag No.: 08, 0C
ET098
DRIVER'S SEAT BELT CONTACT
NOTESThere must be no present or stored faults.
Fasten the driver's seat belt: status ET098 Driver's seat belt contact should be
PRESENT and the instrument panel warning light should go out.
Test the multiplex network and the airbag (see 88B, Multiplexing and 88C, Airbag and pretensioners).
AFTER REPAIRCarry out another fault finding check on the system.
Deal with any other faults.
Clear the stored faults.
TDB_V08_ET098/TDB_V0C_ET098

83A-33
MR-372-J84-83A000$630.mif
V8
83A
INSTRUMENT PANEL
Fault finding - Parameter summary table
Tool parameter Diagnostic tool title
PR002Fuel sender unit resistance
PR005Oil change frequency in km.
PR006Oil change frequency in months.
PR007Distance to next oil service: actual value in km
PR008Oil service interval: actual value in months
PR009Mileometer
PR027Coolant temperature
PR035Fuel level
PR099Vehicle speed
PR110Battery voltage
PR111Lighting dimmer voltage
PR112Fuel flow
PR115LPG fuel level
PR116Engine speed
PR117Fuel consumed since trip computer reset
TDB ph2 (EG/MG)
Prog Version: 04xx
Vdiag No.: 08, 0C
MR-372-J84-83A000$630.mif

83A-34
MR-372-J84-83A000$693.mif
V8
83A
INSTRUMENT PANEL
Fault finding - Interpretation of parameters
TDB_V08_PR027 /TDB_V0C_PR027
PR027
COOLANT TEMPERATURE
NOTESWith the engine running to vary the temperature, check the consistency between the
value of this parameter and the instrument panel display.
In the event of inconsistency, consult the interpretation of command AC008 Instrument panel needles.
Otherwise, test the multiplex network and the injection (see 88B Multiplexing, 13B Diesel injection and 17B
Petrol injection).
AFTER REPAIRCarry out another fault finding check on the system.
Deal with any other faults.
Clear the stored faults.
TDB ph2 (EG/MG)
Prog Version: 04xx
Vdiag No.: 08, 0C
MR-372-J84-83A000$693.mif

83A-35
MR-372-J84-83A000$693.mif
V8
INSTRUMENT PANEL
Fault finding - Interpretation of parameters83A
TDB ph2 (EG/MG)
Prog Version: 04xx
Vdiag No.: 08, 0C
PR099
VEHICLE SPEED
NOTESCarry out a road test and check the consistency of the instrument panel display.
In the event of inconsistency, consult the interpretation of command AC008 Instrument panel needles.
If not, test the multiplex network and the anti-lock braking system (see 88B Multiplexing and 38C Anti-lock
braking system).
AFTER REPAIRCarry out another fault finding check on the system.
Deal with any other faults.
Clear the stored faults.
TDB_V08_PR099 /TDB_V0C_PR099

83A-36
MR-372-J84-83A000$693.mif
V8
INSTRUMENT PANEL
Fault finding - Interpretation of parameters83A
TDB ph2 (EG/MG)
Prog Version: 04xx
Vdiag No.: 08, 0C
PR112
CURRENT SETPOINT
NOTESWith the engine idling, the flow should be around 0.
Vary the engine speed to confirm the increase in flow.
Note: A fault with the fuel flow signal causes inconsistencies in the operation of the
trip computer.
Test the multiplex network and the injection (see 88B Multiplexing, 13B Diesel injection and 17B Petrol
injection).
AFTER REPAIRCarry out another fault finding check on the system.
Deal with any other faults.
Clear the stored faults.
TDB_V08_PR112/TDB_V0C_PR112

83A-37
MR-372-J84-83A000$693.mif
V8
INSTRUMENT PANEL
Fault finding - Interpretation of parameters83A
TDB ph2 (EG/MG)
Prog Version: 04xx
Vdiag No.: 08, 0C
PR115
LPG FUEL LEVEL
NOTESNone
Test the multiplex network and the LPG computer (see 88B Multiplexing and 17B Petrol injection).
If the resistance and level parameters are inconsistent, contact the Techline.
AFTER REPAIRCarry out another fault finding check on the system.
Deal with any other faults.
Clear the stored faults.
TDB_V08_PR115/TDB_V0C_PR115

83A-38
MR-372-J84-83A000$693.mif
V8
INSTRUMENT PANEL
Fault finding - Interpretation of parameters83A
TDB ph2 (EG/MG)
Prog Version: 04xx
Vdiag No.: 08, 0C
PR116
ENGINE SPEED
NOTESWith the engine running, vary the engine speed to check the consistency between the
diagnostic tool and the instrument panel.
In the event of inconsistency, consult the interpretation of command AC008 Instrument panel needle gauges.
Otherwise, test the multiplex network and the injection (see 88B Multiplexing, 13B Diesel injection and 17B
Petrol injection).
AFTER REPAIRCarry out another fault finding check on the system.
Deal with any other faults.
Clear the stored faults.
TDB_V08_PR116/TDB_V0C_PR116

83A-39
MR-372-J84-83A000$693.mif
V8
INSTRUMENT PANEL
Fault finding - Interpretation of parameters83A
TDB ph2 (EG/MG)
Prog Version: 04xx
Vdiag No.: 08, 0C
PR117
FUEL CONSUMED SINCE TRIP COMPUTER RESET
NOTESCheck the consistency with the mileage covered since the trip computer was reset
to zero.
After the instrument panel has been reset to zero or replaced, it is necessary to drive
at least 400 yards to activate the calculation.
Test the multiplex network and the injection (see 88B Multiplexing, 13B Diesel injection and 17B Petrol
injection).
AFTER REPAIRCarry out another fault finding check on the system.
Deal with any other faults.
Clear the stored faults.
TDB_V08_PR117/TDB_V0C_PR117

83A-40
MR-372-J84-83A000$756.mif
V8
83A
INSTRUMENT PANEL
Fault finding - Command summary table
Tool command Diagnostic tool title
RZ001Fault memory
AC006Buzzer
AC007Display
AC008Instrument panel needle gauges
AC009Instrument panel warning lights
AC010Lighting
AC011Symbol display
VP002Write VIN
VP006Oil change frequency in km.
VP007Oil change frequency in months.
VP008Distance to next oil service: actual value in km
VP009Oil service interval: actual value in months
VP010Mileometer updating
VP011Fuel tank sender unit calibration
TDB ph2 (EG/MG)
Prog Version: 04xx
Vdiag No.: 08, 0C
MR-372-J84-83A000$756.mif