lights SAAB 9-2X 2006 Owners Manual

1
– CONTINUED –
WarrantiesWarranties for U.S.A.
All Saab vehicles distributed by Saab of
America, Inc. and sold at retail by an au-
thorized Saab dealer in the United States
come with the following warranties:

Saab Limited Warranty

Emission Control Systems Warranty

Emissions Performance Warranty
All warranty information, including details
of coverage and exclusions, is in the
“Warranty and Maintenance Booklet”.
Please read these warranties carefully.
Warranties for Canada
All Saab vehicles distributed by Saab
Canada, Inc. and sold at retail by an au-
thorized Saab dealer in Canada come
with the following warranties:

Saab Limited Warranty

Anti-Corrosion Warranty

Emission Control Warranty
All warranty information, including details
of coverage and exclusions, is in the
“Warranty and Maintenance Booklet”.
Please read these warranties carefully.

HID headlights
3
How to use this owner’s man-ual
Using your Owner’s manualBefore you operate your vehicle, carefully
read this manual. To protect yourself and
extend the service life of your vehicle, fol-
low the instructions in this manual. Failure
to observe these instructions may result in
serious injury and damage to your vehicle.
This manual is composed of fourteen
chapters. Each chapter begins with a brief
table of contents, so you can usually tell at
a glance if that chapter contains the infor-
mation you want.
Chapter 1: Seats, seatbelts and SRS
airbags
This chapter informs you how to use the
seat and seatbelt and contains precau-
tions for the SRS airbags.
Chapter 2: Keys and doors
This chapter informs you how to operate
the keys, locks and windows.
Chapter 3: Instruments and controls
This chapter informs you about the opera-
tion of instrument panel indicators and
how to use the instruments and other
switches.
Chapter 4: Climate Control
This chapter informs you how to operate
the climate control. High-intensity-discharge (HID)
headlights contain mercury. For that
reason, it is necessary to remove
HID headlights before vehicle dis-
posal. Once removed, please reuse,
recycle or dispose of the HID head-
lights as hazardous waste.
Ask your Saab dealer to check
whether your vehicle is equipped
with HID headlights.
A1910BE-A-GSAAB.book Page 1 Tuesday, September 6, 2005 8:37 AM
ProCarManuals.com

3
Vehicle symbolsThere are some of the symbols you may
see on your vehicle.
Symbol Name
CAUTIONPower door lock and unlockPassenger’s windows lock
and unlockFuelFront fog lightsParking lightsHazard warning flasherCigarette lighterEngine hoodSeat heater
Child restraint top tether an-
choragesChild restraint lower anchor-
agesHornWindshield wiper deicerWiper intermittentWindshield wiper and wash-
erRear window wiper and
washerLightsParking lights, tail lights, li-
cense plate light and instru-
ment panel illuminationHead lightsIllumination brightness Symbol Name
Fan speedInstrument panel outletsInstrument panel outlets and
foot outletsFoot outletsWindshield defroster and
foot outletsWindshield defrosterRear window defogger/Out-
side mirror defoggerAir recirculationOutside airEngine oilWasherDoor lock (transmitter) Symbol Name
A1910BE-A-GSAAB.book Page 3 Tuesday, September 6, 2005 8:37 AM
ProCarManuals.com

17
– CONTINUED –

Warning and indicator lightSymbol Name Page
Seatbelt warning light 3-9SRS airbag system
warning light3-10Passenger airbag ON
indicator light3-10Passenger airbag OFF
indicator light3-10CHECK ENGINE
warning light/Malfunc-
tion indicator lamp3-11Charge warning light 3-11Oil pressure warning
light3-11Automatic transmis-
sion Oil temperature
warning light 33-12
or
ABS warning light 3-12
or
Brake system warning
light3-13
ON orOFF or
Door open warning
light3-13All-Wheel Drive warn-
ing light (AT) 3

3-14
Turn signal indicator
lights3-14High beam indicator
light3-14Security system indi-
cator light2-7Cruise control indica-
tor light3-14Cruise control set indi-
cator light3-15 Symbol Name Page
A1910BE-A-GSAAB.book Page 17 Tuesday, September 6, 2005 8:37 AM
ProCarManuals.com

1-10
Seat, seatbelt and SRS airbags

Expectant mothers
Expectant mothers also need to use the
seatbelts. They should consult their doctor
for specific recommendations. The lap
belt should be worn securely and as low
as possible over the hips, not over the
waist.
Emergency Locking Retrac-
tor (ELR)The driver’s seatbelt has an Emergency
Locking Retractor (ELR).
The emergency locking retractor allows
normal body movement but the retractor
locks automatically during a sudden stop,
impact or if you pull the belt very quickly
out of the retractor.

Automatic/Emergency Lock-
ing Retractor (A/ELR)Each passenger’s seatbelt has an Auto-
matic/Emergency Locking Retractor (A/
ELR). The Automatic/Emergency Locking
Retractor normally functions as an Emer-
gency Locking Retractor (ELR). The A/
ELR has an additional locking mode “Au-
tomatic Locking Retractor (ALR) mode” in-
tended to secure a child restraint system.
When the seatbelt is once drawn out com-
pletely and is then retracted even slightly,
the retractor locks the seatbelt in that po-
sition and the seatbelt cannot be extend-
ed. As the belt is rewinding, clicks will be
heard which indicate the retractor func-
tions as an ALR. When the seatbelt is re-
tracted fully, the ALR mode is released.
When securing a child restraint system on
the rear seats by the use of the seatbelt,
the seatbelt must be changed over to the
Automatic Locking Retractor (ALR) mode.
When the child restraint system is re-
moved, make sure that the seatbelt re-
tracts fully and the retractor returned to
the Emergency Locking Retractor (ELR)
mode.
For instructions on how to convert the re-
tractor to the ALR mode and restore it to
the ELR mode, see the “Child restraint
systems” section in this chapter.

Seatbelt warning light
and chimeYour vehicle is equipped with a seatbelt
warning device at the driver’s seat, as re-
quired by current safety standards.
There is a seatbelt warning light in the
combination meter.
If the driver has not yet fastened the seat-
belt when the ignition switch is turned to
the “ON” position, the seatbelt warning
light will flash for 6 seconds, to warn that
the seatbelt is unfastened. If the driver’s
seatbelt is not fastened, a chime will also
sound simultaneously.
If the driver’s seatbelt is still not fastened
6 seconds later, the warning light will re-
main lit for 15 seconds. If the driver’s seat-
belt is still not fastened even 15 seconds
later (21 seconds after turning ON the ig-
nition switch), the warning lights will alter-
nate between flashing and steady illumi-
nation at 15-second intervals, and the
chime will sound while the warning light is
flashing.
Alternate flashing and steady illumination
of the warning lights and sounding of the
chime will continue until the driver fastens
the seatbelt.
100100
A1910BE-A-GSAAB.book Page 10 Tuesday, September 6, 2005 8:37 AM
ProCarManuals.com

Keys and doors
2-7
2
– CONTINUED –
Remote keyless entry sys-temTwo transmitters are provided for your ve-
hicle.
The remote keyless entry system has the
following functions.

Locking and unlocking the doors (and
rear liftgate) without a key

Sounding a panic alarm

Arming and disarming the alarm sys-
tem. See the next section “Alarm system”
for detailed information.
This device complies with Part 15 of
the FCC Rules and with RSS-210 of In-
dustry Canada. Operation is subject to
the following two conditions: (1) This
device may not cause harmful interfer-
ence, and (2) this device must accept
any interference received, including in-
terference that may cause undesired
operation.
Changes or modifications not express-
ly approved by the party responsible
for compliance could void the user’s
authority to operate the equipment.
The operable distance of the keyless entry
system is approximately 30 feet (10
meters). However, this distance will vary
depending on environmental conditions.The system’s operable distance will be
shorter in areas near a facility or electronic
equipment emitting strong radio waves
such as a power plant, broadcast station,
TV tower, or remote controller of home
electronic appliances.
The remote keyless entry system does not
operate when the key is inserted in the ig-
nition switch to prevent accidental lockout.
: LOCK/ARM button
Press to Lock all doors.
Press and Hold to activate panic
alarm.
Press three times in a five-second
period to use vehicle finder func-
tion.: UNLOCK/DISARM button
1) Press once to Unlock driver’s
door.
2) Press a second time to Unlock
all other doors (and rear lift-
gate).

Locking the doorsBriefly press the “ ” button (for less
than two seconds) to lock all doors (and
rear liftgate).
An electronic chirp will sound once and
the turn signal lights will flash once.
Do not expose the transmitter to
severe shocks, such as those ex-
perienced as a result of dropping
or throwing.

Do not take the transmitter apart
except when replacing the bat-
tery.

Do not get the transmitter wet. If it
gets wet, wipe it dry with a cloth
immediately.
200885
A1910BE-A-GSAAB.book Page 7 Tuesday, September 6, 2005 8:37 AM
ProCarManuals.com

2-8
Keys and doors
If any of the doors is not fully closed, an
electronic chirp will sound five times and
the turn signal lights will flash five times to
alert you that the doors are not properly
closed. When you close the door, it will au-
tomatically lock.NOTEIf the “ ” button is pressed for two
seconds or longer, the panic alarm will
sound. When locking the doors in nor-
mal circumstances, press the “ ”
button for less than two seconds. For
details on the panic alarm, refer to
“Sounding a panic alarm”.
Unlocking the doorsBriefly press the “ ” button (for less
than two seconds) to unlock the driver’s
door. An electronic chirp will sound twice
and the turn signal lights will flash twice.
To unlock all other doors (and rear lift-
gate), briefly press the “ ” button a
second time within 5 seconds.NOTEIf the interval between the first and sec-
ond presses of the “ ” button (for
unlocking of all of the doors and the
rear liftgate) is extremely short, the
system may not respond.

Illuminated entryThe interior (dome) light and ignition
switch light (for turbo models) will illumi-
nate when the “ ” button is pressed.
These lights stay illuminated for approxi-
mately 30 seconds if any of the doors (or
the rear liftgate) is not opened.
If the “ ” button is pressed before 30
seconds have elapsed, these lights will go
out. Also, these lights will go out if the key
is inserted in the ignition switch. The inte-
rior light switch must be set to the middle
position in order for this function to oper-
ate.
Vehicle finder functionUse this function to find your vehicle
parked among many vehicles in a large
parking lot. Provided you are within 30
feet (10 meters) of the vehicle, pressing
the “ ” button three times in a five-sec-
ond period will cause your vehicle’s horn
to sound once and its turn signal lights to
flash three times.NOTEIf the interval between presses is too
short when you press the “ ” button
three times, the system may not re-
spond to the signals from the remote
transmitter.

Sounding a panic alarmTo activate the alarm, keep the “ ” but-
ton pressed for more than two seconds.
The horn will sound and the turn signal
lights will flash.
To deactivate it, press the “ ” button or
“ ” button. Unless a button on the re-
mote is pressed, the alarm will be deacti-
vated after approximately 30 seconds.
Selecting audible signal op-
erationUsing an electronic chirp, the system will
give you an audible signal when the doors
lock and unlock. If desired, you may turn
the audible signal off.
Do the following to deactivate the audible
signal. You can also use the same steps
to restore the function.
1. Sit in the driver’s seat and shut all
doors and the rear liftgate.
2. Open the driver’s door, then remove
the key from the ignition switch.
3. Hold down the “UNLOCK” side of the
power door locking switch.
4. While holding down the “UNLOCK”
side of the power door locking switch, in-
sert the key into the ignition switch and re-
move it again at least 6 times within 10
seconds after Step 3.
5. While still holding down the “UNLOCK”
A1910BE-A-GSAAB.book Page 8 Tuesday, September 6, 2005 8:37 AM
ProCarManuals.com

Keys and doors
2-9
2
– CONTINUED –
side of the power door locking switch,
close the driver’s door once within 10 sec-
onds after Step 4.
6. The turn signal lights flashes 3 times to
indicate completion of the setting.NOTEIf you do not close the driver’s door
within 10 seconds after Step 4, a flash
of the turn signal lights will signal time-
out. If this happens, repeat the whole
procedure from Step 1.
You may have the above settings done by
your Saab dealer.
Replacing the batteryWhen the transmitter battery begins to get
weak, transmitter range will begin to de-
crease. Replace the battery as soon as
possible.To replace the battery:
0
1. Open the transmitter case using a flat-
head screwdriver.
2. Separate the case.
3. Remove the old battery from the hold-
er.
1) Negative (–) side facing up4. Replace with a new battery (Type
CR2025 or equivalent) making sure to in-
stall the new battery with the negative (–)
side facing up.
5. Reinstall the back half of the transmit-
ter case by snapping it back on.
After the battery is replaced, the trans-
mitter must be synchronized with the
keyless entry system’s control unit.
Press either the “ ” or “ ” button
six times to synchronize the unit.
200888200716

Do not let dust, oil or water get on
or in the transmitter when replac-
ing the battery.
1200717
A1910BE-A-GSAAB.book Page 9 Tuesday, September 6, 2005 8:37 AM
ProCarManuals.com

Keys and doors
2-13
2
– CONTINUED –
Alarm systemThe alarm system helps to protect your
vehicle and valuables from theft. The horn
sounds and the turn signal lights flash if
someone attempts to break into your vehi-
cle. The starter motor is also interrupted to
prevent starting the vehicle without a key.
The system can be armed and disarmed
with the remote transmitter.
The system does not operate when the
key is inserted into the ignition switch.
Your vehicle’s alarm system has been set
for activation at the time of shipment from
the factory. You can set the system for de-
activation yourself or have it done by your
Saab dealer.
System operationThe alarm system will give the following
alarm when triggered:

The vehicle’s horn will sound and the
turn signal lights will flash for 30 seconds.
In addition, the starter motor will not oper-
ate.

If any door or the rear liftgate remains
open after the 30-second period, the horn
will continue to sound for a maximum of 3
minutes. If the door and the rear liftgate
are closed while the horn is sounding, thehorn will stop sounding with a delay of up
to 30 seconds.
The alarm is triggered by:

Opening a door or the rear liftgate.

Turning the ignition switch to the “ON”
position.


Activating and deactivating
the alarm system
To change the setting of your vehicle’s
alarm system for activation or deactiva-
tion, do the following.
1. Disarm the alarm system (see “Disarm-
ing the system” in this section).
2. Sit in the driver’s seat and shut all
doors and the rear liftgate.
3. Turn the ignition switch to the “ON” po-
sition.
4. Hold down the UNLOCK side of the
driver’s power door locking switch, open
the driver’s door within the following 1 sec-
ond, and wait 10 seconds without releas-
ing the switch. The setting will then be
changed as follows:
If the system was previously activated:
The horn sounds twice, indicating that the
system is now deactivated.
If the system was previously deactivated:
The horn sounds once, indicating that the
system is now activated.
NOTEYou may have the above setting
change done by your Saab dealer.

If you have accidentally trig-
gered the alarm system

To stop the alarm
Do any of the following operations:

Press any button on the remote trans-
mitter.

Cycle the ignition switch from the
“LOCK” to “ON” position three times within
5 seconds.
Arming the system
To arm the system using remote
transmitter
1. Close all windows and them moonroof
(if equipped).
2. Remove the key from the ignition
switch.
3. Open the doors and get out of the vehi-
cle.
4. Make sure that the engine hood is
locked.
5. Close all doors and the rear liftgate.
A1910BE-A-GSAAB.book Page 13 Tuesday, September 6, 2005 8:37 AM
ProCarManuals.com

2-14
Keys and doors:Press to Arm the system.
: Press to Disarm the system.
Security indicator light
6. Briefly press the “ ” button (for lessthan two seconds). All doors and the rear
liftgate will lock, an electric chirp will
sound once, the turn signal lights will flash
once, and the indicator lights will start
flashing rapidly. After rapid flashing for 30
seconds (standby time), the indicator
lights will then flash slowly (twice approxi-
mately every two seconds), indicating that
the system has been armed for surveil-
lance.
If any of the doors or the rear liftgate is not
fully closed, an electronic chirp sounds
five times, the turn signal lights flash five
times to alert you that the doors or the rear
liftgate are not properly closed. When you
close the door, the system will automati-
cally arm and doors will automatically
lock.

To arm the system using power
door locking switches
1. Close all windows.
2. Remove the key from the ignition
switch.
3. Open the doors and get out of the vehi-
cle.
4. Make sure that the engine hood is
locked.
5. Close the doors and the rear liftgate
but leave only the driver’s door or the front
passenger’s door open.6. Push the front side (“LOCK” side) of
the power door locking switch to set the
door locks.
7. Close the door. An electronic chirp will
sound once, the turn signal lights will flash
once, and the indicator lights will start
flashing rapidly. After rapid flashing for 30
seconds (standby time), the indicator
lights will then flash slowly (twice approxi-
mately every two seconds), indicating that
the system has been armed for surveil-
lance.
NOTE
The system can be armed even if the
engine hood, the windows and/or
moonroof are opened. Always make
sure that they are fully closed before
arming the system.
200885200873
200883
A1910BE-A-GSAAB.book Page 14 Tuesday, September 6, 2005 8:37 AM
ProCarManuals.com

Keys and doors
2-15
2
– CONTINUED –

The 30-second standby time can be
eliminated if you prefer. Have it per-
formed by your Saab dealer.

The system is in the standby mode
for a 30-second period after locking the
doors with the remote transmitter. The
security indicator light will flash at
short intervals during this period.

If any of the following actions is done
during the standby period, the system
will not switch to the surveillance state.

Doors are unlocked using the re-
mote transmitter.

Any door or the rear liftgate is
opened.

Ignition switch is turned to the
“ON” position.

The engine does not start even when
the ignition switch is turned to the
“START” position once the alarm sys-
tem has been triggered.
Disarming the systemBriefly press the “ ” button (for less
than two seconds) on the remote transmit-
ter. The driver’s door will unlock, an elec-
tronic chirp will sound twice, the turn sig-
nal lights will flash twice and the indicator
light will go off.
NOTE (Models with immobiliz-
er)If your vehicle is equipped with an im-
mobilizer, the immobilizer’s function
will cause the security indicator light to
flash (approximately once every three
seconds) even after the system is dis-
armed.NOTEThe system can be disarmed by the fol-
lowing method.

Cycle the ignition switch from the
“LOCK” to the “ON” position three
times within 5 seconds.

Emergency disarming
If you cannot disarm the system using the
transmitter (i.e. the transmitter is lost, bro-
ken or the transmitter battery is too weak),
you can disarm the system without using
the transmitter.
1. Unlock the door with the key and then
open the door.
2. Insert the key into the ignition switch
and cycle it from the “LOCK” to the “ON”
position three times within 5 seconds.
Valet modeWhen you choose the valet mode, the se-
curity system does not operate. In valet
mode, the remote transmitter is used onlyfor locking and unlocking the doors and
rear liftgate and panic activation.
To enter the valet mode, change the set-
ting of your vehicle’s alarm system for de-
activation mode. (Refer to “Activating and
deactivating the alarm system” in this sec-
tion.) The security indicator light will con-
tinue to flash once every three seconds in-
dicating that the system is in the valet
mode (only vehicle with an immobilizer).
To exit valet mode, change the setting of
your vehicle’s alarm system for activation
mode. (Refer to “Activating and deactivat-
ing the alarm system” in this section.)
NOTEIf your vehicle is not equipped with an
immobilizer, the security indicator light
does not flash during the valet mode.
Passive armingWhen passive arming mode has been
programmed by the dealer, arming of the
system is automatically accomplished
without using the remote transmitter. Note
that in this mode, DOORS MUST BE
MANUALLY LOCKED.

To enter the passive mode
If you wish to program the passive arming
mode, have it done by your Saab dealer.
A1910BE-A-GSAAB.book Page 15 Tuesday, September 6, 2005 8:37 AM
ProCarManuals.com