Seat Toledo 2008 COMMUNICATION SYSTEM

Communication
10
Dialogue
The voice command system can be activated via the “press to
talk” key on the phone adapter or the key on the multi-func-
tion wheel.
In this manual, Dialogue is defined as the time in which the voice command
system may receive vocal commands and provide assistance for the comple-
tion of different functions where the user is hesitant and unsure how to
proceed. The system also responds with vocal messages. The dialogue is
activated and deactivated by pressing the “talk button” Ÿpage 6, fig. 1.
If a call is received, then the dialogue is immediately interrupted. To accept
the call, press button “answer call” on the multi-function steering
wheel or press on the radio display.
Assistance from voice control system when orders are not recognised.
If a command is not recognised by the system, it will answer with the cue
<Please repeat?> and the command can then be given once again clearly. After a third failure the system will answer with
<Cancel> and the dialogue will
be ended.
Please note the following to ensure that you are properly understood:
•Speak in a normal tone and without pauses or exaggerated pronuncia-
tion.
•Avoid poor articulation of words.
•Keep the doors, windows and sun roof closed if possible to avoid back-
ground noises that might affect the system.
•Keep the air vents directed away from the microphone (located on the
interior light).
•At high speeds, you might need to speak louder to drown out background
noises.
•Avoid other noises in the vehicle during a dialogue (e.g. other passengers
speaking in the vehicle).
•Avoid speaking when the system is saying a cue.
•The hands-free microphone is directed towards the driver, therefore, only
the driver should try to operate the system.
•To make a call when there is heavy background noise we recommend
using the speech controlled telephone book instead of saying individual
digits. This will help avoid mistakes when specifying telephone numbers.
Micro off
If, at any time, we do not wish to be heard by the person on the other end of
the line during a call, the vehicle microphone can be temporarily discon-
nected. To do so, press on the radio display during the call Ÿ fig. 8. To
reactivate the micro, press on the radio display again.Fig. 8 Current phone call
AF
AEok
micromicro

Communication11
Controls and equipment
Controlling the hands-free unit by voice
The hands-free functions are also operated via voice commands.
Help commands
The system confirms acceptance of speech commands verbally and guides
you through the dialogue if necessary.
Commands for operating the hands-free system
Speech commands for operating the phone book
CommandEffect
HELPFollowing this command the system announces possible orders
CommandEffect
DIAL NUMBERAfter this command you can specify a telephone number and establish a con-
nection
REDIALAfter this command the last dialled telephone number will be redialled
CommandEffect
SELECT NAMEAfter this command, you can call a number that has been recorded in the
phone book under a name.
STORE NAMEAfter this command you can store a name with a telephone number in the
phone book
DELETE NAMEAfter this command you can delete a name from the phone book.
PLAY PHONE BOOKAfter this command you can listen to the names stored in the phone book
DELETE PHONE BOOKAfter this command you can choose to dele te the entire phone book or just a
single name

Communication
12
Control commands
The control commands are used to carry out functions that have already been selected.
The control commands are used during or at the end of a dialogue to carry out
certain functions.
Possible commands
Dial number
A telephone number can be vocally specified to the system and then dialled.
– Press button to talk Ÿ page 6, fig. 1. Activation of the system
is confirmed by a tone.
– After the tone, say the command DIAL NUMBER.After this command the system will then request you to specify a telephone
number. A connection will then be established to the specified number. The
telephone number can be specified all at once, in blocks of digits (separated
by a brief pause), or as single digits. You can specify the digits from zero to
nine . After each block of digits you specify (separated by a brief pause) the
CommandEffect
DIALTelephone number already entered is dialled.
STOREA name is saved in the phonebook with its phone number
CANCELCancels a running dialogue.
REPEATThe specified name or all of the digits specified up to this point will be
repeated. The system will then give the cue <Please proceed> so that you can
specify additional digits or commands.
CORRECTIONThe specified name or the last entered block of digits will be deleted. The sys-
tem will then give the cue <Please proceed> so that you can specify additional
digits or commands.
DELETEAll specified digits will be deleted. The system will then give the cue <The
number has been deleted. Please, proceed> so that you can specify new digits
or commands.
AF

Communication13
Controls and equipmentsystem will repeat the digits. The system can only recognise single digits
(one, zero, two, five, etc.), and not combinations of digits (e.g. ten, twenty-
five).
Notes on specifying telephone numbers:
•If the telephone number has more than 20 digits, the system will decline
and give the cue <The number is too long> .
•A Plus (+) can also be placed ahead of the 20 digits.
Example of how to enter a telephone number:
A running dialogue can be cancelled at any time by pressing button to
talk.
CommandConditionMessageEffect
DIAL NUMBERPhone switched on<The number, please?>Dialogue
for example, ZERO, SEVEN, THREE,
ONE<Zero, seven, three, one>Dialogue
If no command is specified, the system responds after about 5 seconds with the next cue.
No command<Possible commands are: Dial, repeat,
back, or specify additional digits>Dialogue
THREE, NINE, TWO<Three, nine, two>Dialogue
DIAL<The number is being dialled.>Dialogue -The telephone number
0731492 will be dialled
End of dialogue
AF

Communication
14
Redial
– Press button to talk Ÿpage 6, fig. 1 .
– After the tone, say the command REDIAL.After giving the command the last number dialled via the hands-free system
will be dialled again.
Example of the REDIAL command:
A running dialogue can be cancelled at any time by pressing button to
talk.
To store names in the phone book
You can store names and telephone numbers in the internal phone book.
– Press button to talk Ÿ page 6, fig. 1. The beep tone indicates
that the system is ready.
– After the tone, say the command STORE NUMBER.
After giving the command the system will request you to specify a name and
telephone number to store in the internal phone book. The telephone book can store 50 names and numbers. You can specify the digits from zero
to
nine .
The telephone number can be specified all at once, in blocks of digits (sepa-
rated by a brief pause), or as single digits. After each block of digits you
specify (separated by a brief pause) the system will repeat the digits. The
system can only recognise single digits (one, zero, two, five, etc.), and not
combinations of digits (e.g. ten, twenty-five).
Say STORE to store the entry in the phone book.
AF
CommandConditionMessageEffect
REDIALPhone switched on<The number is being dialled.>Dialogue
End of dialogue
AF
AF
CommandConditionMessageEffect
STORE NAMEPhone book is not full<The name, please?>Dialogue
COMPANY XYZ<Please repeat the name>Dialogue

Communication15
Controls and equipmentA running dialogue can be cancelled at any time by pressing button to
talk.
Note
•If the telephone number has more than 20 digits, the system will decline
and give the cue <The number is too long> .
•A Plus (+) can also be placed ahead of the 20 digits.
•Say the command delete or back to delete or correct the corresponding
block of digits.
•Say repeat to have all the digits that have been recognised up to that
point repeated.
•If two or more names sound alike, it is better to save the names including
the first name or some other distinguishing entry.
•A running dialogue can be cancelled at any time by pressing button to
talk.
•The phone book works only in conjunction with the hands-free voice
command system; the entries are not stored on the phone SIM card.
COMPANY XYZ<The number, please?>Dialogue
ZERO, ONE, TWO, THREE<Zero, one, two, three>Dialogue
FOUR, FIVE, SIX<Four, five, six>Dialogue
If no command is specified, the system responds after about 5 seconds with the next cue.
No command<Possible commands are: Store,
repeat, back, delete, or specify addi-
tional digits>Dialogue
STORE<The name has been saved.>Dialogue - The name COMPANY XYZ
with the telephone number 0123456
has been stored
End of dialogue
AF
AF

Communication
16
Calling a name in the phone book
– Press button to talk Ÿpage 6, fig. 1 .
– After the tone, say the command SELECT NAMEAfter the system has recognised this command, you may select a stored entry
from the telephone book to call the required number. The system best recog-
nises names spoken by the person who stored the name.
Example of how to select a name from the internal phone book
A running dialogue can be cancelled at any time by pressing button to
talk.AF
CommandConditionMessageEffect
SELECT NAMEPhone is switched on, telephone book
contains entries.<The name, please?>Dialogue
COMPANY XYZ<Company XYZ>Dialogue
If no command is specified, the system responds after about 5 seconds with the next cue.
No command<Possible commands are: select,
repeat, back>Dialogue
DIAL<The number is being dialled.>Dialogue - The telephone number for
Company XYZ is being dialled
End of dialogue
AF

Communication17
Controls and equipment
Listening to the phone book
You can have the entries stored in the internal telephone book read out to you.
– Press button to talk Ÿpage 6, fig. 1. The beep tone indicates
that the system is ready.
– Say the command PLAY PHONE BOOK.After giving the command the system will read out the entries stored in the
phone book. Press the talk button as an entry is being read to select the
telephone number for that entry. Once the dialogue is complete and the
system is reactivated, you can also select an entry to call by specifying the
stored name.
Example of the PLAY PHONE BOOK command:
Example of how to select an entry:
To delete names from the phone book
You can delete entries from the internal phone book.
– Press the talk button Ÿpage 6, fig. 1 . The beep tone indi-
cates that the system is ready.
– After the tone, say the command DELETE NAME .After giving this command you can delete a stored entry from the internal tele-
phone book.
AFAF
CommandConditionMessageEffect
PLAY PHONE BOOKThe telephone book contains entries. Dialogue - The telephone book will
then be read out.
End of dialogue
CommandConditionMessageEffect
PLAY PHONE BOOKThe telephone book contains entries;
Press the talk button on hearing
the entry required.<The number is being dialled.>Dialogue - The selected name will be
repeated. The telephone number will
be dialled.
End of dialogue
AF
AF

Communication
18
Example of how to delete an entry from the phone book:
A running dialogue can be cancelled at any time by pressing button to
talk.
Note
•Say the command Repeat, if you would like to have the specified name
repeated by the system.
•If you then say No, the system will answer with <Cancel> and the dialogue
will be ended.
To delete the phone book
You can delete the entire phone book or single entries.
– Press the talk button Ÿpage 6, fig. 1 .
– After the tone, say the command DELETE PHONE BOOK.
After giving this command you can delete the entire internal phone book or
single entries as desired.
CommandConditionMessageEffect
DELETE NAMEThe telephone book contains entries.<The name, please?>Dialogue
COMPANY XYZ<Do you want to delete the entry Com-
pany XYZ?>Dialogue
If no command is specified, the system responds after about 5 seconds with the next cue.Dialogue
No command<Possible commands are: yes, no,
repeat, back>Dialogue
Ye s<The name has been deleted.>Dialogue
End of dialogue
AF
AF

Communication19
Controls and equipmentExample of how to delete the entire internal telephone book:
Example of how to delete one entry from the internal phone book:
CommandConditionMessageEffect
DELETE PHONE BOOKThe telephone book contains entries.<Would you like to delete the whole
phone book?>Dialogue
If no command is specified, the system responds after about 5 seconds with the next cue.Dialogue
No command<Possible commands are: Yes, no>Dialogue
Ye s<Are you sure?>Dialogue
If no command is specified, the system responds after about 5 seconds with the next cue.Dialogue
No command<Possible commands are: Yes, no>Dialogue
Ye s<The phone book has been deleted.>Dialogue - All entries in the phone
book will be deleted.
End of dialogue
CommandConditionMessageEffect
DELETE PHONE BOOKThe telephone book contains entries.<Would you like to delete the whole
phone book?>Dialogue
If no command is specified, the system responds after about 5 seconds with the next cue.Dialogue
No command<Possible commands are: Yes, no,
repeat>Dialogue
NODialogue - The telephone book will
then be read out.
No commandPress talk button on hearing the
entry to be deleted.<Do you want to delete the entry
(name)?>Dialogue
If no command is specified, the system responds after about 5 seconds with the next cue.Dialogue