SKODA FABIA 2006 2.G / 5J Owner's Guide

Instruments and Indicator/Warning Lights20
The outside temperature appears in the display when the ignition is switched on.
The correct outside temperature will be indicated with a delay of 5 minutes. If the vehicle is stationary (or driven at a very low speed) the temperature indi- cated may be slightly higher than the actual outside temperature because of heat radiated by the engine.
If the outside temperature drops below +4 °C, a snow flake symbol (warning signal for ice on the road) appears wi th the outside temperature indicator ⇒ page 19, fig. 7 and a warning signal* sounds for 10 seconds.
WARNING
Do not only rely upon the information given on the outside temperature display that there is no ice on the road. Please note that black ice may also be present on the road surface ev en at temperatures around +4 °C - warning, drive with care!
Note
The outside temperature is not indicating when showing navigation data (guid-ance to the destination). It must be ca lled up over the menu (valid for vehicles which have a navigation and information display).
Range
The estimated range in kilometres is shown on the display. It indicates the distance you can still drive with your vehicle based on the present level of fuel in the tank for the same style of driving. The readout is shown in steps of 10 km.
The fuel consumption for the last 50 km is taken as a basis for calculating the range. If you drive in a more econom ical manner from this moment on, the range will be increased accordingly.
You first drive 50 km if the readout is reset (after disconnecting the battery) before a new readout for the range is displayed.
Current fuel consumption
The current fuel consumption level is show n in the display in litres/100 km. This information can help you to adapt your st yle of driving to the fuel consumption you wish to achieve.
The display appears in litres/hour if the vehicle is stationary or driving at a low speed.
Average fuel consumption
The average fuel consumption since the memory was last erased is shown in the display in litres/100 km ⇒page 18. This information can help you to adapt your style of driving to the fuel consumption you wish to achieve.
If you wish to determine the average fuel consumption over a certain period of time you must first erase the memory at the start of the new measurement using the button ⇒page 19, fig. 6. A zero appears in the display for the first 300 m you drive after erasing the memory.
The indicated value will be updated every 5 seconds while you are driving.
Note
The amount of fuel consum ed will not be indicated.
AB
NKO A05Fabia 20.book Page 20 Tuesday, September 26, 2006 8:38 AM

Instruments and Indicator/Warning Lights21
Using the systemSafetyDriving TipsGeneral MaintenanceBreakdown assistanceTechnical Data
Driving time
The driving time which has elapsed since the memory was last erased, appears in the display ⇒page 18. If you wish to calculate the driving time from a partic- ular time of day you must first erase th e memory at this moment in time by pressing the button ⇒page 19, fig. 6.
The maximum time indicated in both switch positions is 99 hours and 59 minutes. The indicator is set back to null if this period is exceeded.
Distance driven
The distance driven since the memory was last erased appears in the display ⇒ page 18. If you wish to calculate the distance driven from a particular time of day you must first erase the memory at this moment in time by pressing the button ⇒page 19, fig. 6.
The maximum distance indicated in both switch positions is 9999 km. The indi- cator is set back to null if this period is exceeded.
Average speed
The average speed since the memory was last erased is shown in the display in km/hour ⇒page 18. If you wish to determine the average speed over a certain period of time you must first erase the memory at the start of the new measure- ment using the button ⇒page 19, fig. 6.
A zero appears in the display for the first 100 m you drive after erasing the memory.
Information display*
Introduction
The information display provides you wi th information in a convenient way concerning the current operating state of your vehicle. The information system also provides you with data (depending on the equipment installed in the vehicle) relating to the radio, multi-functional indicator and navigation system.
Certain functions and operating conditio ns are always being checked on the vehicle when the ignition is switched on and also while driving.
Functional faults, if required repair wo rk and other information are indicated by red symbols ⇒page 24 and yellow symbols ⇒page 25.
Lighting up of these symbols is combin ed with an acoustic warning signal.
Information and texts giving warnings are also shown in the display ⇒ page 26.
AB
AB
AB
Fig. 8 Instrument cluster: Information display
NKO A05Fabia 20.book Page 21 Tuesday, September 26, 2006 8:38 AM

Instruments and Indicator/Warning Lights22
The display of text is possible in the following languages:
Czech, English, German, French, Italian, Spanish, Portuguese.
You can select the relevant language in the menu of the information display.
The following information can be show n in the display (depending on the equipment installed on the vehicle):
Menu
– You can activate the menu by pressing the rocker switch
⇒ fig. 10 for more than 1 second.
– You can select the menu through the rocker switch . The
selected information is displayed after pressing the button for
a short time or after releasing th e rocker switch (after about 4
seconds).
You can select the following inform ation (depending on the equipment installed on the vehicle):
Menu⇒ page 22
Door, tailgate and bonnet ajar warning⇒page 23
Radio display⇒page 23
Service Interval Display⇒page 16
Phone⇒page 120
Selector lever positions of the 6-speed automatic gearbox⇒ page 112
Fig. 9 Information display: Menu
MFD (MFA)⇒ page 17
VEH. STATUS⇒page 23
NAVIGATION⇒page 25
LANGUAGE⇒page 21
DISPLAY OFF
Fig. 10 Information display: Control elements
AA
AA
AB
AA
NKO A05Fabia 20.book Page 22 Tuesday, September 26, 2006 8:38 AM

Instruments and Indicator/Warning Lights23
Using the systemSafetyDriving TipsGeneral MaintenanceBreakdown assistanceTechnical Data
After selecting the menu DISPLAY OFF the display is switched off. Press rocker switch for at least 1 second to switch the display on again.
The Information VEH. STATUSflashes in the menu if there is something which is not in proper order on the vehicle (e.g . warning of a low fuel level). The first warning will be displayed after switching over to VEH. STATUS. You can then display other operating conditions afterw ards using the rocker switch function (such as water level low).
Door, tailgate and bonnet ajar warning
The door, tailgate compartment door an d bonnet ajar warning lights up when at least one of the three items door, tai lgate or bonnet are not closed when the ignition is turned on. The symbol indica tes which door is still open or whether the tailgate or bonnet is not closed ⇒fig. 11.
The symbol goes out as soon as the d oors, tailgate and bonnet are completely closed.
As an additional warning signal, a 3 time peep sounds if the car is driven at a speed of more than 6km/hour and if the door or the tailgate is open.
Radio display
These displays appear in addition to the normal information in the radio display.
Auto Check Control
Car state
The Auto Check Control carries out a ch eck of certain functions and vehicle components. The check is performed consta ntly when the ignition is switched on, both when the vehicle is stat ionary, as well as when driving.
AA
Fig. 11 Information display: Door warning
Fig. 12 Information display: Radio display
NKO A05Fabia 20.book Page 23 Tuesday, September 26, 2006 8:38 AM

Instruments and Indicator/Warning Lights24
Operational faults, urgent repairs, service work or other information appear in the display of the instrument cluster. The displays are shown with a red or yellow light symbol depending on the priority of the message.
The red symbols indicate danger (priority 1) while the yellow symbols indicate a warning (priortity 2). Information for the driver may also appear in addition to the symbols ⇒page 26.
Investigate the displayed faults as soon as possible. If several operational faults exist at the same time, the symbols will appear one after the other and light up each for about 10 seconds.
The error messages are displayed and stored in the menu VEH. STATUS.
There is at least one error message to be read when the term VEH. STATUS is flashing in the main menu. The display will show STATUS 1/2 (for example) if a number of error messages are displayed. This display indicates that the first of a total of two error messages should be displayed.
Actuate the rocker switch , to call up the individual error messages.
If a fault occurs, a warning signal will also sound in addition to the symbol and text in the display:
•Priority 1 - three warning signals,
•Priority 2 - one warning signal.
Red symbols
A red symbol signals danger.
Proceed as follows if a red symbol is displayed:
– Stop the vehicle.
– Switch the engine off.
– Investigate the function indicated.
– Obtain professional assistance.
Meaning of the red symbols:
AA
Coolant level too low/coolant temperature too high⇒ page 30
Engine oil pressure too low⇒page 31
Fig. 13 Information display: Oil pressure is low
NKO A05Fabia 20.book Page 24 Tuesday, September 26, 2006 8:38 AM

Instruments and Indicator/Warning Lights25
Using the systemSafetyDriving TipsGeneral MaintenanceBreakdown assistanceTechnical Data
Three successive warning signals will sound if a red symbol appears.
If several operational faults of priority 1 exist, the symbols appear one after the other and are each illumi nated for about 5 seconds.
Ye l l o w s y m b o l s
A yellow symbol signals a warning.
The meaning of the yellow symbols:
One warning signal will sound if a yellow symbol appears.
If several operational faults of priority 2 exist, the symbols appear one after the other and are each illuminated for about 10 seconds.
Check the relevant function as soon as possible.
Navigation system*
The controls for the navigation system, radio, CD player are located in the centre console on both sides of the mo nitor screen. Navigation data is also shown in the information display of the instrument cluster.
Information and warning texts are displaye d preferentially when the navigation system is switched on.
Operation of the navigation system is described in separate operating instruc- tions to be found in the on-board literature.
Fig. 14 Information display: Fuel level low
Fuel level low⇒ page 31
Check engine oil level, engine oil sensor faulty⇒page 31
Brake pad worn⇒page 32
Washer fluid level low⇒page 32
NKO A05Fabia 20.book Page 25 Tuesday, September 26, 2006 8:38 AM

Instruments and Indicator/Warning Lights26
Warning lights
Overview
The warning lights indicate certain functions or faults.
Fig. 15 Instrument cluster with warning lights
Turn signal lights (to the left)⇒ page 28
Turn signal lights (to the right)⇒page 28
Main beam⇒page 28
Low beam⇒page 28
Rear fog light⇒page 28
Dynamo⇒page 28
Fog lights*⇒page 28
Cornering lights*⇒page 28
NKO A05Fabia 20.book Page 26 Tuesday, September 26, 2006 8:38 AM

Instruments and Indicator/Warning Lights27
Using the systemSafetyDriving TipsGeneral MaintenanceBreakdown assistanceTechnical Data
WARNING
•If you do not pay attention to the warning lights coming on and the corresponding descriptions and warning notes, this may result in severe body injuries or major vehicle damage.
•The engine compartment of your car is a hazardous area. There is a risk of injuries, scalding, accidents and fire when working in the engine compartment, e.g. inspecting and replenishing oil and other fluids. It is also essential to observe all warnings ⇒page 198.
Note
•Arrangement of the indicator lights depends on the model and model version. The symbols shown in the following functional description are to be found as indicator lights in the instrument cluster.
•Operational faults are shown in the instrument cluster as red symbols (priority 1 - danger) or yellow symbols (priority 2 - warning).
Electrohydraulic power steering⇒ page 29
EPC fault light (petrol engine)⇒page 29
Glow plug system (diesel engine)⇒page 29
Turn signal system for vehicles towing a trailer*⇒ page 30
Coolant temperature/coolant level⇒page 30
Electronic immobiliser⇒page 31
Fuel reserve⇒page 31
Engine oil⇒page 31
Brake pad wear*⇒page 32
Open door*⇒page 32
Fluid level in windshield washer system*⇒page 32
Control system for exhaust⇒page 32
Traction control system (TCS)*⇒page 33
Tyre pressure*⇒page 33
Selector lever lock* (automatic gearbox)⇒page 33
Electronic stability programme (ESP)*⇒page 33
Antilock brake system (ABS)*⇒page 34
Brake system⇒page 34
Airbag system⇒page 35
Diesel particle filter* (diesel engine)⇒page 36
Seat belt warning light*⇒page 37
NKO A05Fabia 20.book Page 27 Tuesday, September 26, 2006 8:38 AM

Instruments and Indicator/Warning Lights28
Turn signal system 
Either the left  or right  indicator light flashes depending on the position of the turn signal lever.
The indicator light flashes at twice its normal rate if a turn signal light fails. This does not apply when towing a trailer.
Switching off the hazard warning light system is switched on will cause all of the turn signal lights as well as both indicator lights to flash.
Further information about the turn signal system ⇒page 60.
Main beam 
The indicator light  comes on when the main beam is selected or also when the headlight flasher is operated.
Further information about the main beam ⇒page 60.
Low beam 
The indicator light  comes on when low beam is selected ⇒page 56.
Rear fog light 
The warning light  comes on when the rear fog lights are operating ⇒ page 58.
Alternator 
The warning light  comes on after the ignition has been switched on. It should go out after the engine has started.
If the warning light does not go out after the engine has started, or comes on when driving, drive to the nearest specialist garage. The vehicle battery will be discharged in this case so switch off all non-essential electrical components.
The following text will be displayed in the information display*:
ALTERNATOR WORKSHOP!
Caution
If the warning light  comes on when driving and in addition the warning light  (cooling system fault) also comes on in display, you must then stop the car immediately and switch the engine off - risk of engine damage!
Fog lights* 
The warning light  comes on when the fog lights are operating ⇒page 58.
Cornering lights* 
If the warning light  flashes for 1 minute while driving or after switching on the ignition and a warning signal sounds, a fault is confirmed.
Further information ⇒page 57.
NKO A05Fabia 20.book Page 28 Tuesday, September 26, 2006 8:38 AM

Instruments and Indicator/Warning Lights29
Using the systemSafetyDriving TipsGeneral MaintenanceBreakdown assistanceTechnical Data
WARNING
f there is a fault in the cornering lights, the headlights are automatically lowered to the emergency position. Thus the illuminated length of the road is shortened. Drive carefully and have the car inspected immedi-ately by a specialist garage.
Electrohydraulic power steering 
The warning light  comes on for a few seconds when the ignition is switched on.
If the warning light after switching on th e ignition or when driving lights up continuously, a fault exists in th e electrohydraulic power steering.
•If the yellow warning light lights up, this indicates a partial or total failure of the power steering and the steering forces can be greater.
Further information ⇒page 170.
WARNING
Contact your specialist garage if the power steering is defective.
Note
•If the yellow warning light  goes out after starting the engine again and a short drive, it is not necessary to visit a specialist garage.
•If the battery has been disconnected and reconnected, the yellow warning light  comes on after switching on the igni tion. The warning light must go out after driving a short distance.
•There is no power-assisted steering support when the vehicle is being towed without the engine running or when the power-assisted steering is
defect. The vehicle is fully steerable ho wever. There is simply increased force required to turn the steering wheel.
EPC fault light  (petrol engine)
The  (Electronic Power Control) warning light comes on for a few seconds when the ignition is switched on.
There is a system fault in the engine control system if the warning light  does not go out or comes on or flashes while driving. The engine management system selects an emergency programme which enables you to drive to the nearest specialist garage by adopting a gentle style of driving.
The following text will be displayed in the information display*:
ENGINE FAULT WORKSHOP!
Glow plug system  (diesel engine)
The indicator light  lights up for a cold engine when switching on the ignition (pre-heat position) 2 ⇒page 104. Start the engine after the indicator light goes out.
The glow plug indicator light will come on for about 1 second if the engine is at a normal operating temperature or if the outside temperature is above +5°C. This means that you can start the engine right away.
There is a fault in the glow plug system if the indicator light  does not come on at all or lights up continuously. Contact a specialist garage as soon as possible to obtain professional assistance.
There is a system fault in the engine control system if the warning light  has started to flash while driving. The engi ne management system selects an emer-
NKO A05Fabia 20.book Page 29 Tuesday, September 26, 2006 8:38 AM