ECU SKODA YETI 2009 1.G / 5L User Guide

Seats and Stowage
77
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
– The middle seat backrest can be folded
⇒page 74, “Folding rear seats forwards”
forwards and used as armres
t or table with cup holder
⇒page 76, fig. 73
.
– You can place two cups or beverage cans into the recesses.
Note
If the middle rear seat backrest should be
folded forward for lengthy periods, then
make sure that the belt locks are not located below it - this can result in permanent damage to the upholstery.Seat heating of the front seats*You can electrically heat the seat cushions and the seat backrests of the front seats.Front seats– You can switch on and regulate the seat heating of the driver or front passenger
seat by pressing the surface of the regulator at the point at which the symbol is located
 ⇒fig. 74
.
– With one press, you can switch the heating to highest intensity which is indicated
by the lighting up of the three warning lights in the switch.
– With repeated pressing of the switch, the intensity of the heating is down-regulated
up to the switch-off. The intensity of the heating is indicated by the number of illu- minated warning lights in the switch.
WARNING
If, as an occupant, you have a subdued pain and/or temperature sensitivity, e.g. through medication, paralysis or because of chronic illness (e.g. diabetes), we recommend not to use the seat heating.
This can lead to burns on the back, the
posterior and the legs which
are difficult to heal. If the seat heating is used, we
recommend to make regular breaks in your journey when driving long distances, so that in specific cases as
mentioned above the body can recuperate
from the stress of the journey. Please consult your doctor, who can evaluate your specific condition.
Caution
•
You should not kneel on the seats or otherwise apply pressure at specific points in
order to avoid damaging the heating elements of the seat heaters.•
Do not use the seat heating if the seats ar
e not occupied by persons or if objects
are fastened or stored on them, for example a child seat, a bag etc. A fault of the heating elements in the seat heating can occur.•
Do not clean the seats moist
⇒page 197.
Note
•
The seat heating should only be switched on when the engine is running. This has
a significant effect of savi
ng on the battery capacity.
•
If the on-board voltage drops, the seat heating is switched off automatically, in
order to provide sufficient electrical energy for the engine control.PedalsConcerning a secure depressing of the peda
l, you should use only footmats from the
Škoda genuine accessories. Operation of the pedals must not be hindered!
WARNING
•
Greater pedal distances may be needed when there is a fault in the brake
system.
Fig. 74 Dash panel: Regulator for front seat heating
sgg.6.book Page 77 Thursday, September 24, 2009 2:32 PM

Seats and Stowage
78•
Do not place any footmats or other additional floor coverings in the area of
the pedals in order to ensure that all the pedals can be fully depressed and are able to return unobstructed to their initial position - risk of accident!•
There must be no objects on the floor
which could roll under the pedals. You
would then no longer be able to apply
the brakes, operate the clutch or acceler-
ator - risk of accident!Luggage compartmentLoading the luggage compartmentPlease observe the following in the interest of having good handling characteristics of your vehicle: – Distribute the items of luggage as evenly as possible. – Place heavy objects as far forward as possible.– Attach the items of luggage to the lashing eyes or the fixing net*
⇒page 79.
In the event of an accident, there is such a
high kinetic energy wh
ich is produced by
small and light objects that they can cause se
vere injuries. The magnitude of the kinetic
energy depends on the speed at which the vehi
cle is travelling and on the weight of the
object. The speed at which the vehicle is travelling is in this case the more significant factor. Example: In the event of a frontal collision at a speed of 50 km/h, an unsecured object with a weight of 4.5 kg produces an ener
gy, which corresponds to 20 times its own
weight. This means that it results in a weight of approx. 90 kg. You can imagine the inju- ries that can occur, if this “bullet” is fl
ying through the interior
compartment and hits
an occupant.
WARNING
•
Store the objects in the luggage compartment and attach them to the
lashing eyes, e.g. with the fixing nets.
•
Loose objects in the passenger compartment can be thrown forward during
a sudden manoeuvre or in case of an a
ccident and can injure the occupants or
other oncoming traffic. This risk is still increased, if the objects which are flying around are hit by a deployed airbag. In this case, the objects which are thrown back can injure the occupants - hazard.•
Please note that the handling properti
es of your vehicle may be affected
when transporting heavy objects as a result
of the displacement of the centre of
gravity. The speed and style of driv
ing must be adjusted accordingly.
•
The items carried in the luggage compartment should be stowed in such a
way that no objects are able to slip forward if there are any sudden driving or braking manoeuvres undertaken - risk of injury!•
Never drive with the boot lid fully open
ed or slightly ajar otherwise exhaust
gases may get into the interior of the vehicle - risk of poisoning!•
On no account exceed the permissible
axle loads and the permissible gross
weight of the vehicle - risk of accident!•
Never transport occupants in the luggage compartment!Caution
Please ensure that the heating elements of the rear window heater are not damaged as a result of objects sliding in this area.
Note
Tyre pressure must be adjusted to the load
⇒page 215.
WARNING (continued)
WARNING (continued)
sgg.6.book Page 78 Thursday, September 24, 2009 2:32 PM

Seats and Stowage
80 Move the hook into another position– Fold up the hook in direction of arro
w until an angle of 45° is reached
⇒ page 79, fig. 77
.
– Move the hook in direction of arrow into the desired position and fold down the
hook as far as the stop
in direction of arrow
⇒page 79, fig. 77
.
Remove the hook from the fastening strip– Fold the hook in direction of arrow until it slackens.Install the hook on the fastening strip– Position the hook on the fastening strip in
the vertical position in direction of arrow
and lightly press it on.
– Fold the hook down in opposite direct
ion of the arrow until it locks fully.
WARNING
Please refer to the following guidelines
⇒page 78.
Fixing nets - Net programme*Fig. 78 Fixing net: double horizontal pocket
, floor fixing net / double vertical pockets
Fixing examples of the fixing net as do
uble horizontal pocket, floor fixing net
⇒fig. 78

on the left and double vertical pocket
⇒fig. 78
on the right.
The fixing nets* and the installation inst
ruction are located in the luggage compart-
ment.
WARNING
•
The whole strength of the net makes it possible to load the pocket with
objects of up to 3.5 kg in weight. Heavy
objects are not secured sufficiently - risk
of injury and net damage!•
The load to be transported must be fixed in place in such a way that it cannot
move during the journey and when braking.
Caution
Do not place any objects with sharp edge
s in the nets - risk of net damage.
The luggage compartment cover You can use the luggage compartment cover behind the head restraints for storing
light and soft items.
The luggage compartment cover can be remo
ved as required if one must transport
bulky goods.Removing the luggage compartment cover– Fold the seat backrests a little forward in order to facilitate the removal of the
luggage compartment cover.
– Unhook the support straps on the boot lid
⇒fig. 79
.
A1
A2
A3
A4
A5
A4
Fig. 79 Removing the luggage compart- ment coverA1
sgg.6.book Page 80 Thursday, September 24, 2009 2:32 PM

Seats and Stowage
82 Pack static separation net– Press the red button of the joint - so that it releases. – Put the separation net folded together in the bag and close it. – Attach the bag with the aid of the plastic carabines to the eyes on the left and right
luggage compartment trim panel.
Installing and removing the static separation net behind the rear seats with variable loading floor*
⇒page 82 is carried out analogously as
behind the rear seats without
variable loading floor. Use the lower fixing ey
es on the carrier rails in order to attach
the carabines. The opening
⇒page 81, fig. 80
in the static separation net is designed to feed
through the three-point seat belt
⇒page 144.
Variable loading floor*Remove variable loading floorFig. 81 Luggage compartment: fold up variable
loading floor / remove variable loading floor
The variable loading floor makes it easier to handle bulky goods and creates an even luggage compartment floor when the rear seat backrests are folded forward. The maximum permissable surface load of the variable loading floor is 75 kg.
Remove variable loading floor– You can fold together the loading floor
by moving in direction of arrow
⇒ fig. 81
.
– Raise the floor in direction of arrow
⇒fig. 81
.
– Pull on both sides of the locking levers in direction of arrow
⇒fig. 81
.
– Pull the loading floor up and out in direction of arrow . – The installation of the variable loading floor is carried out in the reverse order.Secure the variable loading floor in the raised position– Fold up the hooks on the fastening strip in direction of arrow
⇒page 79, fig. 77
.
– Fold up the variable loading floor behind
the seat backrests of the rear seats.
– Fold down the hooks in direction
of arrow as far as the stop
⇒page 79, fig. 77
.
– Support the variable loading floor on the hooks folded downwards.
WARNING
Pay attention when installing that the ca
rrier rails and the variable loading floor
are correctly fixed, otherwis
e the occupants are at risk.
Note
If the variable loading floor* is installed, no flexible storage compartment can be installed.
AA
AD
A1
A2
A3
A4
A1
A3
sgg.6.book Page 82 Thursday, September 24, 2009 2:32 PM

Seats and Stowage
83
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Remove carrier railsFig. 82 Luggage compartment: Slacken
check points / remove carrier rails
Install carrier rails– Slacken the check points on the carrier rails using the vehicle key or a flat screw-
driver
⇒fig. 82
.
– Grasp the carrier rail at the position
⇒fig. 82
and slacken it by pulling in the
direction of arrow.
– Grasp the carrier rail at the position ,
slacken it by pulling in the direction of
arrow and take it out.
– The carrier rail on the other side of
the luggage compartment can be removed in
the same way.
Install carrier rails– Position the carrier rails on the
sides of the luggage compartment.
– Press both check points on each carrier rail up to the stop. – Check the attachment of the carrier rails by pulling it.
WARNING
Pay attention when installing that the carrier rails are correctly fixed, otherwise the occupants are at risk.
Variable loading floo
r* with spare wheel*
Use variable loading floorFig. 83 Luggage compartment: Fold the side parts of the loading floor / example for using the variable loading floorThe variable loading floor makes it easier to handle bulky goods and creates an even luggage compartment floor when the rear seat backrests are folded forward. The maximum permissable surface load of the variable loading floor is 75 kg. You can fold down the side parts of the loading floor in direction arrow in order to enlarge the space foreseen for stowing items of luggage
⇒fig. 83
.
Note
If the variable loading floor with spare wheel*
is installed, no flexible storage compart-
ment can be installed.•
The variable loading floor with spare wheel*
can be secured in the raised position
in the same way as the variable loading floor without spare wheel*
⇒page 82, “Secure
the variable loading floor in the raised position”.
AB
AA
A1
AA
A2
sgg.6.book Page 83 Thursday, September 24, 2009 2:32 PM

Seats and Stowage
93
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Removing– Take hold of the flexible storage
compartment at both upper corners.
– Press the upper corners to the inside
and release the storage compartment by
pulling upwards.
– Remove by pulling towards you.Installing– Insert both ends of the flexible storage
compartment into the openings of the right
side trim panel of the luggage compartment and push it downwards until it locks.
Clothes hooksThe clothes hooks are located on the middle
pillar and on the handle of the headliner
above each of the rear doors.
WARNING
•
Ensure that any clothes hanging from the hooks do not impair your vision to
the rear.•
Use the hooks for hanging only light item
s of clothing and ensure that there
are no heavy or sharp-edge
d objects in the pockets.
•
The maximum permissable load of the hooks is 2 kg.
•
Do not use clothes hangers for hanging up items of clothing otherwise this
will interfere with the protection offered by the head airbag*.
Removeable through-loading bag*The removeable through-loading bag
is solely used for transporting
skis.The removeable through-loading bag is foreseen for two pairs of skis. The total weight of the skis which are transported must not exceed 10 kg.Loading– Open a rear side door of the vehicle. – Fold the backrest of the middle seat forwards
⇒page 74.
– Place the empty removeable through-loading bag in the gap between the front and
rear seats in such a way that the end of
the bag with the zip lies in the luggage
compartment.
– Open the boot lid.– Push the skis into the removeable through-loading bag from the luggage compart-
ment
⇒
.
– Close the removeable through-loading bag with the zip.Securing– Pull the securing belt with both lock to
ngues out of the pocket of the removeable
through-loading bag.
– Insert the lock tongues in the belt locks
of the rear middle seat belt , first of
all on the one side and then on the other side
⇒fig. 105
.
Fig. 105 Securing the removeable through-loading bag
AA
AC
sgg.6.book Page 93 Thursday, September 24, 2009 2:32 PM

Seats and Stowage
94– Place the securing belt in the middle of
the skis between the heel and the tip of the
bindings and pull the secu
ring belt tight at the free end of the belt .
Stowing– Carefully fold the empty (dry) removeable through-loading bag together, place it in
the luggage compartment and secure it to prevent it slipping.
WARNING
•
After placing the skis into the remove
able through-loading bag, you must
secure it with the securing belt .•
The securing belt must hold the skis tight.
•
Ensure that the securing belt for skis
grasps the middle between the tip and
the heel element of the binding (see al
so imprint on the removeable through-
loading bag).
Note
•
You must put the skis and the sticks in
the removeable through-loading bag with
the tips facing the rear.•
If there are skis with different lengths in the removeable through-loading bag,
ensure that the bindings are always positioned at the same height.•
The removeable through-loading bag must never be folded together or stowed
when moist.
AB
AA
sgg.6.book Page 94 Thursday, September 24, 2009 2:32 PM

Communication
131
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
in a jacket pocket, this can lead to diff
iculties when establishing the Bluetooth
®
connection with the handsfree-
system or the data transfer.
Inserting the mobile phone with the adapter* Inserting the mobile phone into the adapter ensures an optimal sending and receiving power and offers at the same time the advan- tage of the battery charging.Only one telephone mount* is factory-fitted. An adapter for the telephone can be purchased from the range of the Škoda original accessories.Inserting the mobile phone with the adapter– First of all push the adapter in the direction of arrow
⇒fig. 127
up to the stop
into the mount. Press the adapter slightly downwards, until it locks securely into position.
– Insert the mobile phone into the adapter (as specified in manufacturer's
instructions).
Removing the mobile phone with the adapter– Press simultaneouly the side locks of the mount and remove the mobile phone and
adapter
⇒fig. 127
.
Note
Please operate your mobile phone exclusively with a suitable adapter in order to keep a low radiation in the vehicle.Operation of the telephone on the multifunction steering wheel*The driver can set the basic functions of th
e telephone by simply operating the buttons
located on the steering wheel so that he can concentrate on the traffic situation without being distracted as little as
possible by operating the telephone
⇒fig. 128
.
This applies only if your vehicle has been equipped with the telephone preinstallation at the factory. If the side lights are switched on, the buttons on the multifunction steering wheel are illuminated. Overview of the different functions in contrast to the multifunction steering wheel without mobile phone operation
⇒page 126.
Fig. 127 Universal preparation for the phone
AA
AA
Button
Action
Operation
press briefly
Activation/deactivation button for voice control
(button PTT)

 turn upwards
Increase volume

 turn down- wards
Decrease volumeFig. 128 Multifunction steering wheel: Control buttons for the telephone
A1A1A1
sgg.6.book Page 131 Thursday, September 24, 2009 2:32 PM

Communication
134
Enter PIN codeA PIN code must be entered before operating the system. – Press the PTT button. – Give the command
ENTER PIN/PIN CODE
after the signal tone.
After this command the PIN code can be entered. The entry of the PIN code is only possible if:•
the ignition is switched on;
•
the mobile phone is in the mount;
•
the mobile phone is switched on.
Notes for entering the PIN code•
When entering a PIN code with more
than 8 digits, the system indicates “
The PIN
is too long
”.
•
When entering an incorrect PIN code, the system indicates “
The PIN is incorrect
”.
•
If the incorrect PIN code has been entered three times consecutively, the card is
blocked. With the aid of the personal unbl
ocking code PUK (Personal Unblock Key), the
SIM card can be unblocked.
The unblocking code can only be entered via the phone
keypad and not through the voice control.
Voice commands for operating the phone
phone book
Activity
SAVE/STORE
NAMES/NAME/NUMBER
After this command a name
with its telephone number
can be stored in the phone phone book.
SELECT NAMES/NAME
After this command a telephone number which was stored under its given name in the phone phone book can be selected.
DELETE NAMES/NAME
After this command a name in the phone phone book can be erased.
LISTEN TO/PLAY PHONE-
BOOK
After this command you ca
n listen-in to the phone
phone book.
DELETE PHONEBOOK
After this command the comp
lete phone phonebook or
one of the stored names can be erased.
Other possible com-
mands
Activity
DIAL
The telephone number is selected.
STORE
In addition to the name in the phone book, which is selected on the information display, a voice recording is stored to select with the help of the voice commands or the entered PIN code.
REPEAT
The entered name or the digits are repeated. Then the system requests with voice response “
please proceed
”
the entry of further digits or commands.
BACK
The entered name or the last entered order of digits is erased. Previously entered groups of digits are repeated. Then the system requests with voice response “
please
proceed
” the entry of further digits or commands.
DELETE
All entered digits are erased. Then the system requests with voice response “
The number is deleted. The
number please
” the entry of further digits or com-
mands.
CANCEL
The dialogue is ended.
Other possible com-
mands
Activity
sgg.6.book Page 134 Thursday, September 24, 2009 2:32 PM

Communication
136
Load CDs– Hold the button pressed and guide the CDs one after the other (maximum
6 CDs) into the CD case . The LEDs in
the buttons are no longer flashing.
Loading a CD to one definite position– Press on the button . The LEDs in the
buttons light up at the memory spaces,
which are already assigned and flash in the case of free memory spaces.
– Touch the desired button and
guide the CD into the CD-case .
Ejecting a CD– Briefly press on the button , in order to eject a CD. For assigned memory spaces,
now the LEDs light up in the buttons .
– Touch the corresponding bu
tton . The CD is ejected.
Ejecting all CDs– Hold the button pressed for more than 2
seconds, in order to eject the CDs. All
CDs in the CD-changer are ejected consecutively.Note
•
Always guide the CD into the CD-case
with the printed side pointing upwards.
•
Never push the CD with force into the CD-case as the insertion is performed auto-
matically.•
After loading a CD into the CD-changer, yo
u must wait until the LED of the corre-
sponding button lights up. Then the CD
-case is free to load the next CD.
•
If you have selected a position, on which
a CD is already located, this CD will be
ejected. Take out the ejected CD and load the desired CD.
AA
AB
AD
AA
AD
AD
AB
AC
AD
AD
AC
AB
AD
AB
sgg.6.book Page 136 Thursday, September 24, 2009 2:32 PM