battery location SUZUKI GRAND VITARA 2005 2.G Service User Guide

YH4
GRAND
VITARA
8B
LIGHTING SYSTEM 8B-1
SECTION 8B
LIGHTING SYSTEM
WARNING:
For vehicles equipped with Supplemental Restraint (Air Bag) System:

Service on and around the air bag system components or wiring must be performed only by an autho-
rized SUZUKI dealer. Refer to ªAir Bag System Components and Wiring Location Viewº under ªGener-
al Descriptionº in air bag system section in order to confirm whether you are performing service on
or near the air bag system components or wiring. Please observe all WARNINGS and ªService Precau-
tionsº under ªOn-Vehicle Serviceº in air bag system section before performing service on or around
the air bag system components or wiring. Failure to follow WARNINGS could result in unintentional
activation of the system or could render the system inoperative. Either of these two conditions may
result in severe injury.

Technical service work must be started at least 90 seconds after the ignition switch is turned to the
ªLOCKº position and the negative cable is disconnected from the battery. Otherwise, the system may
be activated by reserve energy in the Sensing and Diagnostic Module (SDM).
CONTENTS
GENERAL DESCRIPTION8B- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cautions in Servicing8B- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Symbols and Marks8B- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wiring Color Symbols8B- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Abbreviations8B- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Joint Connector8B- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fuse Box and Relay8B- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Supply Diagram8B- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Headlights8B- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Headlight with Leveling System (If Equipped) 8B- 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DIAGNOSIS8B- 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Headlights8B- 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Headlights with Leveling System (If Equipped) 8B- 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Turn Signal and Hazard Warning Lights 8B- 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Clearance, Tail and License Plate Lights 8B- 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Back-up Lights8B- 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Brake Lights8B- 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rear Fog Light (If Equipped)8B- 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Interior Lights8B- 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ON-VEHICLE SERVICE8B- 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Headlights8B- 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Headlights with Leveling System (If Equipped) 8B- 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Turn Signal and Hazard Warning Lights 8B- 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rear Fog Light (If Equipped)8B-11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

YH4
GRAND
VITARA
8C
INSTRUMENTATION / DRIVER INFORMATION 8C-1
GENERAL DESCRIPTION8C- 2 . . . . . . . . . . . . . .
Cautions in Servicing 8C- 2. . . . . . . . . . . . . . . . .
Symbols and Marks 8C- 2. . . . . . . . . . . . . . . . . . .
Wiring Color Symbols 8C- 2. . . . . . . . . . . . . . . . .
Abbreviations 8C- 2. . . . . . . . . . . . . . . . . . . . . . . .
Joint Connector 8C- 2. . . . . . . . . . . . . . . . . . . . . .
Fuse Box and Relay 8C- 2. . . . . . . . . . . . . . . . . .
Power Supply Diagram 8C- 2. . . . . . . . . . . . . . . .
Combination Meter 8C- 2. . . . . . . . . . . . . . . . . . .
DIAGNOSIS8C- 4 . . . . . . . . . . . . . . . . . . . . . . . . . . .
Speedometer and VSS 8C- 4. . . . . . . . . . . . . . . .
Fuel Meter / Fuel Gauge Unit 8C- 4. . . . . . . . . . . .
Engine Coolant Temp. (ECT) Meter and
Sensor 8C- 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Oil Pressure Light 8C- 4. . . . . . . . . . . . . . . . . . . .
Brake and Parking Brake Warning
Light 8C- 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Light Remainder Warning Buzzer 8C- 5. . . . . . . Seat Belt Warning Light (If Equipped) 8C- 5. . .
Ignition Key Remainder Warning
Buzzer (If Equipped) 8C- 5. . . . . . . . . . . . . . . . .
Cigarette Lighter and Accessory Socket 8C- 5.
ON-VEHICLE SERVICE8C- 6 . . . . . . . . . . . . . . . .
Ignition (Main) Switch 8C- 6. . . . . . . . . . . . . . . . .
Combination Meter 8C- 7. . . . . . . . . . . . . . . . . . .
Speedometer and VSS 8C- 8. . . . . . . . . . . . . . . .
Fuel Meter / Fuel Gauge Unit 8C- 9. . . . . . . . . . . .
Engine Coolant Temp. (ECT) Meter and
Sensor 8C-10. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Oil Pressure Light 8C-11. . . . . . . . . . . . . . . . . . . .
Brake and Parking Brake Warning
Light 8C-12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ignition Key Remainder (If Equipped) /
Light Remainder Warning Buzzer 8C-12. . . . . .
Door Switch 8C-13. . . . . . . . . . . . . . . . . . . . . . . . .
Seat Belt Warning Light (If Equipped) 8C-13. . .
SECTION 8C
INSTRUMENTATION/DRIVER INFORMATION
WARNING:
For vehicles equipped with Supplemental Restraint (Air Bag) System

Service on and around the air bag system components or wiring must be performed only by an autho-
rized SUZUKI dealer. Refer to ªAir Bag System Components and Wiring Location Viewº under ªGener-
al Descriptionº in air bag system section in order to confirm whether you are performing service on
or near the air bag system components or wiring. Please observe all WARNINGS and ªService Precau-
tionsº under ªOn-Vehicle Serviceº in air bag system section before performing service on or around
the air bag system components or wiring. Failure to follow WARNINGS could result in unintentional
activation of the system or could render the system inoperative. Either of these two conditions may
result in severe injury.

Technical service work must be started at least 90 seconds after the ignition switch is turned to the
ªLOCKº position and the negative cable is disconnected from the battery. Otherwise, the system may
be activated by reserve energy in the Sensing and Diagnostic Module (SDM).
CONTENTS

YH4
GRAND
VITARA
8D
WINDOWS, MIRRORS, SECURITY AND LOCKS 8D-1
GENERAL DESCRIPTION8D- 2 . . . . . . . . . . . . . .
Cautions in Servicing 8D- 2. . . . . . . . . . . . . . . . .
Symbols and Marks 8D- 2. . . . . . . . . . . . . . . . . . .
Wiring Color Symbols 8D- 2. . . . . . . . . . . . . . . . .
Abbreviations 8D- 2. . . . . . . . . . . . . . . . . . . . . . . .
Joint Connector 8D- 2. . . . . . . . . . . . . . . . . . . . . .
Fuse Box and Relay 8D- 2. . . . . . . . . . . . . . . . . .
Power Supply Diagram 8D- 2. . . . . . . . . . . . . . . .
Windshield Wiper and Washer 8D- 2. . . . . . . . .
Front Wiper and Washer 8D- 2. . . . . . . . . . . . .
Rear Wiper and Washer (If Equipped) 8D- 3.
Power Door Lock and Keyless Entry
(If Equipped) System 8D- 4. . . . . . . . . . . . . . . .
DIAGNOSIS8D- 5 . . . . . . . . . . . . . . . . . . . . . . . . . . .
Windshield Wiper and Washer 8D- 5. . . . . . . . .
Front Wiper and Washer 8D- 5. . . . . . . . . . . . .
Rear Wiper and Washer (If Equipped) 8D- 5.
Rear Window Defogger (If Equipped) 8D- 5. . .
Power Window Control System 8D- 5. . . . . . . . .
Power Door Lock System (If Keyless
Entry is not Equipped) 8D- 6. . . . . . . . . . . . . . . Power Door Lock and Keyless Entry
System (If Keyless Entry is Equipped) 8D- 7. .
Power Door Mirror Control System 8D- 8. . . . . .
Door Mirror Heater (If Equipped) 8D- 8. . . . . . . .
Power Sliding Roof (If Equipped) 8D- 8. . . . . . .
Front Seat Heater (If Equipped) 8D- 8. . . . . . . .
ON-VEHICLE SERVICE8D- 9 . . . . . . . . . . . . . . . .
Windshield Wiper and Washer 8D- 9. . . . . . . . .
Front Wiper and Washer 8D- 9. . . . . . . . . . . . .
Rear Wiper and Washer (If Equipped) 8D-13.
Rear Window Defogger (If Equipped) 8D-16. . .
Power Window Control System 8D-18. . . . . . . . .
Power Door Lock System (If Keyless
Entry is not Equipped) 8D-20. . . . . . . . . . . . . . .
Power Door Lock and Keyless Entry
System (If Keyless Entry is Equipped) 8D-23. .
Power Door Mirror Control System 8D-30. . . . . .
Door Mirror Heater (If Equipped) 8D-31. . . . . . . .
Power Sliding Roof (If Equipped) 8D-32. . . . . . .
Front Seat Heater (If Equipped) 8D-33. . . . . . . .
SECTION 8D
WINDOWS, MIRRORS, SECURITY AND LOCKS
WARNING:
For vehicles equipped with Supplemental Restraint (Air Bag) System:

Service on and around the air bag system components or wiring must be performed only by an autho-
rized SUZUKI dealer. Refer to ªAir Bag System Components and Wiring Location Viewº under ªGener-
al Descriptionº in air bag system section in order to confirm whether you are performing service on
or near the air bag system components or wiring. Please observe all WARNINGS and ªService Precau-
tionsº under ªOn-Vehicle Serviceº in air bag system section before performing service on or around
the air bag system components or wiring. Failure to follow WARNINGS could result in unintentional
activation of the system or could render the system inoperative. Either of these two conditions may
result in severe injury.

Technical service work must be started at least 90 seconds after the ignition switch is turned to the
ªLOCKº position and the negative cable is disconnected from the battery. Otherwise, the system may
be activated by reserve energy in the Sensing and Diagnostic Module (SDM).
CONTENTS

YH4
GRAND
VITARA
8G
IMMOBILIZER CONTROL SYSTEM (IF EQUIPPED) 8G-1
GENERAL DESCRIPTION8G- 2 . . . . . . . . . . . . . .
Ignition Key 8G- 3. . . . . . . . . . . . . . . . . . . . . . . . . .
Coil Antenna 8G- 3. . . . . . . . . . . . . . . . . . . . . . . . .
Immobilizer Control Module 8G- 4. . . . . . . . . . . .
ECM/PCM 8G- 4. . . . . . . . . . . . . . . . . . . . . . . . . . .
On-Board Diagnostic System
(Self-Diagnosis Function) 8G- 4. . . . . . . . . . . . .
DIAGNOSIS8G- 6 . . . . . . . . . . . . . . . . . . . . . . . . . . .
Precautions in Diagnosing Troubles 8G- 6. . . . .
Diagnostic Flow Table <Vehicle equipped
with monitor coupler> 8G- 9. . . . . . . . . . . . . . . .
Diagnostic Flow Table <Vehicle not
equipped with monitor coupler> 8G-10. . . . . . .
Diagnostic Trouble Code Check
(Immobilizer Control Module) 8G-11. . . . . . . .
Diagnostic Trouble Code Check
(ECM / PCM) 8G-11. . . . . . . . . . . . . . . . . . . . . .
Diagnostic Trouble Code Table 8G-13. . . . . . . . .
TABLE A DTC is not Output
from Diagnostic Output Terminal 8G-14. . . . . . .
TABLE B Immobilizer Indicator Lamp
Check (Immobilizer Indicator Lamp
does not Light at Ignition Switch ON) 8G-15. . .
TABLE C Immobilizer Indicator Lamp
Check (Immobilizer Indicator Lamp
Remains on after Engine Starts) 8G-16. . . . . . .
DTC11 Transponder Code Not Matched8G-17 . .
DTC31 Transponder Code Not
Registered 8G-17. . . . . . . . . . . . . . . . . . . . . . . . .
DTC12 Fault in Immobilizer
Control Module 8G-17. . . . . . . . . . . . . . . . . . . . . .
DTC13 No Transponder Code Transmitted
or Coil Antenna Opened/Shorted 8G-18. . . . . . DTC21 ECM/Immobilizer Control Module
Code Not Matched (Immobilizer Control
Module Side) 8G-20. . . . . . . . . . . . . . . . . . . . . . .
DTC81 (P1623) ECM/Immobilizer
Control Module Code Not Matched
(ECM/PCM Side) 8G-20. . . . . . . . . . . . . . . . . . . .
DTC84 (P1620) ECM/Immobilizer Control
Module Code Not Registered 8G-20. . . . . . . . .
DTC22 Ignition Switch Circuit Open/Short8G-21 . .
DTC23 No ECM/Immobilizer Control
Module Code Transmitted from ECM/
PCM or DLC Circuit Opened/Shorted8G-22 . . . .
DTC83 (P1621) No ECM/Immobilizer
Control Module Code Transmitted from
Immobilizer Control Module or DLC
Circuit Opened/Shorted 8G-22. . . . . . . . . . . . . .
DTC82 (P1622) Fault in ECM/PCM 8G-23. . . . .
Inspection of ECM/PCM, Immobilizer
Control Module and Its Circuit 8G-24. . . . . . . . .
Voltage Check 8G-24. . . . . . . . . . . . . . . . . . . . .
Resistance Check 8G-25. . . . . . . . . . . . . . . . . .
ON-VEHICLE SERVICE8G-26 . . . . . . . . . . . . . . . .
Precautions in Handling Immobilizer
Control System 8G-26. . . . . . . . . . . . . . . . . . . . .
Immobilizer Control Module 8G-27. . . . . . . . . . . .
Coil Antenna 8G-27. . . . . . . . . . . . . . . . . . . . . . . . .
HOW TO REGISTER IGNITION KEY8G-28 . . . . .
PROCEDURE AFTER IMMOBILIZER
CONTROL MODULE REPLACEMENT8G-29 . .
PROCEDURE AFTER ECM/PCM
REPLACEMENT8G-30 . . . . . . . . . . . . . . . . . . . . . .
SPECIAL TOOLS8G-30 . . . . . . . . . . . . . . . . . . . . . .
SECTION 8G
IMMOBILIZER CONTROL SYSTEM
(IF EQUIPPED)
WARNING:
For vehicles equipped with Supplemental Restraint (Air Bag) System

Service on and around the air bag system components or wiring must be performed only by an autho-
rized SUZUKI dealer. Refer to ªAir Bag System Components and Wiring Location Viewº under ªGener-
al Descriptionº in air bag system section in order to confirm whether you are performing service on
or near the air bag system components or wiring. Please observe all WARNINGS and ªService Precau-
tionsº under ªOn-Vehicle Serviceº in air bag system section before performing service on or around
the air bag system components or wiring. Failure to follow WARNINGS could result in unintentional
activation of the system or could render the system inoperative. Either of these two conditions may
result in severe injury.

Technical service work must be started at least 90 seconds after the ignition switch is turned to the
ªLOCKº position and the negative cable is disconnected from the battery. Otherwise, the system may
be activated by reserve energy in the Sensing and Diagnostic Module (SDM).
CONTENTS

YH4
GRAND
VITARA
9
BODY SERVICE 9-1
GLASS, WINDOWS AND MIRRORS9- 2 . . . . .
Front Door Glass 9- 2. . . . . . . . . . . . . . . . . . . . .
Front Door Window Regulator 9- 5. . . . . . . . . .
Windshield 9- 6. . . . . . . . . . . . . . . . . . . . . . . . . .
Rear Door Glass 9-12. . . . . . . . . . . . . . . . . . . . .
Rear Door Window Regulator 9-14. . . . . . . . . .
Quarter Window 9-15. . . . . . . . . . . . . . . . . . . . . .
Back Door Glass 9-16. . . . . . . . . . . . . . . . . . . . .
BODY STRUCTURE9-17 . . . . . . . . . . . . . . . . . . .
Front Door Assembly 9-17. . . . . . . . . . . . . . . . .
Rear Door Assembly 9-18. . . . . . . . . . . . . . . . . .
Back Door / Rear Gate Assembly 9-19. . . . . . . .
Hood 9-21. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Front Fender 9-22. . . . . . . . . . . . . . . . . . . . . . . . .
Front Bumper 9-23. . . . . . . . . . . . . . . . . . . . . . . .
Rear Bumper 9-24. . . . . . . . . . . . . . . . . . . . . . . .
Under Body Dimensions 9-25. . . . . . . . . . . . . . .
Body Dimensions 9-26. . . . . . . . . . . . . . . . . . . . .
INSTRUMENTATION AND DRIVER
INFORMATION9-33 . . . . . . . . . . . . . . . . . . . . . . .
Instrument Panel 9-33. . . . . . . . . . . . . . . . . . . . .
SEAT9-34 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Front Seat 9-34. . . . . . . . . . . . . . . . . . . . . . . . . . . Rear Seat 9-35. . . . . . . . . . . . . . . . . . . . . . . . . . .
PAINT AND COATINGS9-36 . . . . . . . . . . . . . . . .
Anti-Corrosion Treatment 9-36. . . . . . . . . . . . . .
Metal Replacement Parts Finishing 9-37. . . . .
Plastic Parts Finishing 9-58. . . . . . . . . . . . . . . . .
SECURITY AND LOCKS9-59 . . . . . . . . . . . . . . . .
Front Door Lock Assembly 9-59. . . . . . . . . . . . .
Rear Door Lock Assembly 9-61. . . . . . . . . . . . .
Back Door / Rear Gate Lock Assembly 9-62. . .
Key Coding 9-63. . . . . . . . . . . . . . . . . . . . . . . . . .
SUNROOF / CONVERTIBLE TOP9-64 . . . . . . . . .
Sliding Roof (if equipped) 9-64. . . . . . . . . . . . . .
Canvas Top And Topbow Frames 9-71. . . . . . .
EXTERIOR AND INTERIOR TRIM9-72 . . . . . . .
Floor Carpet 9-72. . . . . . . . . . . . . . . . . . . . . . . . .
Head lining 9-73. . . . . . . . . . . . . . . . . . . . . . . . . .
Roof Trim (2 Door Model) 9-75. . . . . . . . . . . . . .
Side Moldings (if equipped) 9-77. . . . . . . . . . . .
Splash Guard (if equipped) 9-78. . . . . . . . . . . .
Roof Rail (if equipped) 9-79. . . . . . . . . . . . . . . .
Roof Molding 9-79. . . . . . . . . . . . . . . . . . . . . . . .
Luggage Under Box 9-80. . . . . . . . . . . . . . . . . .
SECTION 9
BODY SERVICE
WARNING:
For vehicles equipped with Supplemental Restraint (Air Bag) System

Service on and around the air bag system components or wiring must be performed only by an autho-
rized SUZUKI dealer. Refer to ªAir Bag System Components and Wiring Location Viewº under ªGener-
al Descriptionº in air bag system section in order to confirm whether you are performing service on
or near the air bag system components or wiring. Please observe all WARNINGS and ªService Precau-
tionsº under ªOn-Vehicle Serviceº in air bag system section before performing service on or around
the air bag system components or wiring. Failure to follow WARNINGS could result in unintentional
activation of the system or could render the system inoperative. Either of these two conditions may
result in severe injury.

Technical service work must be started at least 90 seconds after the ignition switch is turned to the
ªLOCKº position and the negative cable is disconnected from the battery. Otherwise, the system may
be activated by reserve energy in the Sensing and Diagnostic Module (SDM).

When body servicing, if shock may be applied to air bag system component parts, remove those parts
beforehand. (Refer to Section 10B.)
NOTE:
Fasteners are important attaching parts in that they could affect the performance of vital components and
systems, and / or could result in major repair expense. They must be replaced with one of the same part
number of with an equivalent part if replacement becomes necessary.
Do not use a replacement part of lesser quality or substitute a design. Torque values must be used as spe-
cified during reassembly to assure proper retention of these parts.
CONTENTS

YH4
GRAND
VITARA
BODY SERVICE 9-65
Section A ± A
ADJUSTMENT
1) Loosen sunroof glass fixing screws (at 4 locations) and move
sunroof glass up and down 2 to 3 times. In this way, sunroof
glass can be positioned in both vertical and horizontal directions
by elasticity of sliding roof weather strip.
2) Position sunroof glass by such dimensions with respect to roof
panel surface as specified below.
Dimension: ªaº: 0 mm (0.0 in.)
3) After installing all parts and adjusting properly, check sunroof for
proper operation (open, close and up).
SLIDING ROOF DEFLECTOR
REMOVAL
1) Open sliding roof.
2) Disconnect negative cable at battery.
3) Remove screws and disconnect deflector from deflector link.
INSTALLATION
Reverse removal procedure to install deflector.

YH4
GRAND
VITARA
10
RESTRAINT SYSTEM 10-1
SECTION 10
RESTRAINT SYSTEM
WARNING:
For vehicles equipped with Supplemental Restraint (Air Bag) System

Service on and around the air bag system components or wiring must be performed only by an autho-
rized SUZUKI dealer. Refer to ªAir Bag System Components and Wiring Location Viewº under ªGener-
al Descriptionº in air bag system section in order to confirm whether you are performing service on
or near the air bag system components or wiring. Please observe all WARNINGS and ªService Precau-
tionsº under ªOn-Vehicle Serviceº in air bag system section before performing service on or around
the air bag system components or wiring. Failure to follow WARNINGS could result in unintentional
activation of the system or could render the system inoperative. Either of these two conditions may
result in severe injury.

Technical service work must be started at least 90 seconds after the ignition switch is turned to the
ªLOCKº position and the negative cable is disconnected from the battery. Otherwise, the system may
be activated by reserve energy in the Sensing and Diagnostic Module (SDM).
SEAT BELTSECTION 10A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AIR BAG SYSTEMSECTION 10B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CONTENTS
GENERAL DESCRIPTION10-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DIAGNOSISRefer to ªDiagnosisº in SECTION 10A and 10B. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

YH4
GRAND
VITARA
10A
SEAT BELT 10A-1
SECTION 10A
SEAT BELT
WARNING:
For vehicles equipped with Supplemental Restraint (Air Bag) System

Service on and around the air bag system components or wiring must be performed only by an autho-
rized SUZUKI dealer. Refer to ªAir Bag System Components and Wiring Location Viewº under ªGener-
al Descriptionº in air bag system section in order to confirm whether you are performing service on
or near the air bag system components or wiring. Please observe all WARNINGS and ªService Precau-
tionsº under ªOn-Vehicle Serviceº in air bag system section before performing service on or around
the air bag system components or wiring. Failure to follow WARNINGS could result in unintentional
activation of the system or could render the system inoperative. Either of these two conditions may
result in severe injury.

Technical service work must be started at least 90 seconds after the ignition switch is turned to the
ªLOCKº position and the negative cable is disconnected from the battery. Otherwise, the system may
be activated by reserve energy in the Sensing and Diagnostic Module (SDM).
CAUTION:
When fasteners are removed, always reinstall them at the same location from which they were re-
moved. If a fastener needs to be replaced, use the correct part number fastener for that application. If
the correct part number fastener is not available, a fastener of equal size and strength (or stronger) may
be used. Fasteners that are not reused, and those requiring thread-locking compound, will be called
out. The correct torque value must be used when installing fasteners that require it. If the above proce-
dures are not followed, parts or system damage could result.
CONTENTS
GENERAL DESCRIPTIONRefer to SECTION 10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ON-VEHICLE SERVICE10A-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Service precautions10A-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Front seat belt10A-3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rear seat belt10A-6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TIGHTENING TORQUE SPECIFICATIONS10A-6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

YH4
GRAND
VITARA
1. Seat belt pretensioner (retractor assembly)
2. Webbing
3. 185 cm (6 ft) of clearance
4. Exhaust hole
1. Stretch deployment harness to full length 10 m (33 ft).
2. Connect connectors.
3. Power source (12V vehicle battery)
4. Short the two deployment harness leads.
5. Seat belt pretensioner harness
4
AIR BAG SYSTEM 10B-85
6) Pull out the webbing fully as shown at the left and cut it at the
root of the pretensioner (retractor assembly) as shown in the
figure.
WARNING:
As the drum of the retractor assembly turns very quick-
ly as soon as the webbing is cut, fix the retractor assem-
bly with a vise on the workbench and keep your hands
and fingers away from it when cutting the webbing.
7) Clear a space on the ground about 185 cm (6 ft) in diameter
where the seat belt pretensioner is to be activated. A paved,
outdoor location where there is no activity is preferred. If an out-
door location is not available, a space on the shop floor where
there is no activity and sufficient ventilation is recommended.
Ensure no loose or flammable objects are within the activation
area.
8) Place the seat belt pretensioner as shown in the figure on the
ground in the space just cleared.
9) Stretch the deployment harness from the seat belt pretension-
er to its full length 10 m (33 ft).
10) Place a power source near the shorted end of the deployment
harness. Recommended application: 12 Volts minimum, 2
amps minimum. A vehicle battery is suggested.
11) Verify that the area around the seat belt pretensioner is clear
of all people and loose or flammable objects.
12) Verify that the seat belt pretensioner is placed as shown in the
figure on the ground in the space just cleared.
13) Connect the seat belt pretensioner harness to the deployment
harness connector and lock the connector with lock lever.
Special Tool
(A): 09932-75030