reset TOYOTA 4RUNNER 2003 N210 / 4.G Navigation Manual

4Runner_Navi_U (L/O 0208)
1342003 MY 4Runner Navigation from Aug. ’02 Prod. (OM35799U)
(b) Presetting a station1. Tune in the desired station.
2. Touch one of the station selector switch es (16) and hold it until a beep is heard. This sets the station to the switch
and the frequency appears on the switch
Each radio mode (AM, FM1 or FM2) can
store up to 6 stations. To change the
preset station to a different one, follow
the same procedure.
The preset station memory is cancelled
when the power source is interrupted by
battery disconnection or a blown fuse. (c) Selecting a station
Tune in the desired station using one of
the following methods.
Preset tuning: Touch the switch (1
−6) for
the station you want. The switch is high-
lighted in green an d the station frequency
appears on the screen.
Seek tuning: Push the “SEEK/TRACK”
button on either side. The radio will begin
seeking up or down for a station of the
nearest frequency and will stop on recep-
tion. Each time you push the button, the
stations will be searched out one after
another. To scan all the frequencies:
Touch the
“SCAN” switch on the screen or push the
“SCAN” button briefly. “SCAN” appears on
the screen. The radio will find the next
station and stay ther e for a few seconds,
and then scan again. To select a station,
touch the “SCAN” switch or push the
“SCAN” button again.

4Runner_Navi_U (L/O 0208)
1352003 MY 4Runner Navigation from Aug. ’02 Prod. (OM35799U)
To scan the preset stations: Touch the
“SCAN” switch on the screen or push the
“SCAN” button for longer than 2 seconds.
“P. SCAN” appears on the screen. The
radio will tune in the next preset station,
stay there for a few seconds, and then
move to the next preset station. To select
a station, touch the “SCAN” switch or
push the “SCAN” button again.
(d) Radio Data System
Your audio system is equipped with Radio
Data Systems (RDS). RDS mode pro-
vides you to receive text messages from
radio stations that utilize RDS transmit-
ters.
When RDS is on, the radio can
—only select stations of a particular pro-
gram type,
—display messages from radio stations,
—search for a stronger signal station,
—search for local stations broadcasting
the same network as the vehicle travels,
—receive announcements concerning lo-
cal and national emergencies (even if
RDS function is turned off).
RDS features are available for the use
only on FM stations which broadcast RDS
information. “RDS SRCH” (RDS search) switch
This switch allows you to search all avail-
able RDS stations out of the entire FM
band and sort them by program type
(See following “TYPE” switch for details
on program types).
By touching this button at the FM mode,
RDS is turned on and the radio is
switched to FM type mode. During the
program type search, “RDS SEARCH” will
be shown on the screen. Also at this
time, “FM TYPE” will appear on the
screen to indicate that the station selec-
tor switches are for program type.
After searching for all the available RDS
stations, the radio will activate the pre-
viously used program type. If the pre-
viously used program type is not avail-
able, or if the radio has not yet
performed a program type search, the
radio will activate the first available pro-
gram type that has stations in memory.
The radio will preset the stations of the
current program type into the preset but-
tons.
These are accessible through the “TYPE”
switch. If more than 6 stations are found,
the radio will load the 6 strongest sta-
tions signal of the program type into the
presets.

4Runner_Navi_U (L/O 0208)
1732003 MY 4Runner Navigation from Aug. ’02 Prod. (OM35799U)
1. Volume control button
Push “+” to increase the volume. The
volume continues to increase while the
button is being pressed. Push “−
” to decrease the volume. The
volume continues to decrease while the
button is being pressed.
2. “ ” button (Seek, search, track)
Radio
This switch has the following features—
To seek a station:
Quickly push and release the “ ” or “ ”
side of the switch. Do this again to find
the next station. If you push the switch
on either side during the seek mode,
seeking will be cancelled.
To select a preset station:
Push and hold the “ ” or “ ” side of the
switch. Do this again to select the next
preset station.
Cassette tape player
This switch has the following features—
To skip to a different track in either direc-
tion:
Quickly push and release the “ ” or “ ”
side of the switch. “FF 1” or “REW 1” will
appear on the display. Next, push either side of the track switch
until the track you want to listen to is
set. If you push the
switch ten times, the
skip function will turn off. (You can skip
up to nine tracks at a time.)
When counting the number of the tracks
you want to rewind, remember to count
the current track as well. For example, if
you want to rewind to a song that is two
before the song you are listening to,
push the “ ” side of the button three
times.
If you push the track button further than
you wanted to, push the other side of the
button. The track number will be in-
creased or reduced.
The track number you select is not valid
if it is higher than the number of the
tracks remaining on the current side of
the cassette.
When the tape reaches to the begin-
ning, the player will automatically start
playing that side.
After the tape reaches to the end, the
player will automatically reverse and
start playing the other side.