TOYOTA CAMRY 1998 Owners Manual

222
Replacing light bulbs—
The following illustrations show how to
gain access to the bulbs. When replacing
a bulb, make sure the ignition switch and
light switch are off. Use bulbs with the
wattage ratings given in the table.
CAUTION
Halogen bulbs have pressurized gas
inside and require special handling.
They can burst or shatter if scratched
or dropped. Hold a bulb only by its
plastic or metal case. Do not touch
the glass part of a bulb with bare
hands.
NOTICE
Only use a bulb of the listed type.
Light bulbsBulb
No.WTy p e
HeadlightsHB260/55A
Parking, front side
marker and front
turn signal lights
—27/8B
Rear side marker
lights1943.8C
Rear turn signal
lights315627C
Stop and tail lights315727/8C
Tail light9049.3C
Back−up lights92118C
License plate lights—5C
High mounted
stop light21CP18C
Personal light—10B
Interior light—10D
Vanity lights—3D
Glovebox light—1.2C
Trunk light—3.8C
A: HB2 halogen bulbs
B: Single end bulbs
C: Wedge base bulbs
D: Double end bulbs
ProCarManuals.com

223
—Headlights
1. Open the hood. Unplug the connec-
tor. Remove the rubber cover.
If the connector is tight, wiggle it.2. Release the bulb retaining spring
and remove the bulb. Install a new
bulb and the bulb retaining spring.
To install a bulb, align the tabs of the
bulb with the cutouts of the mounting
hole.3. Install the rubber cover with the
”TOP” mark upward, and snuggle on
the boss. Insert the connector. Then
install the plastic cover.
Make sure the rubber cover fits snugly on
the connector and the headlight body.
Aiming is not necessary after replacing
the bulb. When aiming adjustment is nec-
essary, contact your Toyota dealer.
ProCarManuals.com

224
Use a flat−bladed screwdriver. Remove
and install the cover clips as shown in
the following illustrations.Removing cover clips
Installing cover clips
Use a flat−bladed screw driver. To protect
the surface, place several sheets of paper
over the surface.
—Parking, front side marker
and front turn signal lights
ProCarManuals.com

225
a: Rear side marker light
b: Rear turn signal light
c: Stop and tail light
—Rear side maker, rear turn
signal, stop and tail lights
ProCarManuals.com

226
a: Back−up light
b: Tail lightUse a flat−bladed screwdriver. Remove
and install the cover clips as shown in
the following illustrations.
—Back−up and tail lights
(type A)—Back−up and tail lights
(type B)
ProCarManuals.com

227
Removing the cover clips
Installing the cover clipsa: Back−up light
b: Tail light
Use a phillips−head screw driver. Remove
and install the cover clips as shown in
the following illustrations.
—License plate lights
ProCarManuals.com

228
Removing cover clips
Installing cover clips
—High mounted stoplight
ProCarManuals.com

229
ProCarManuals.com

231
Part 8
SPECIFICATIONS
Dimensions and weight
Engine
Fuel
Service specifications
Ti r es
Fuses
Dimensions and weight
ProCarManuals.com

232
Engine
Model:
5S−FE and 1MZ−FE
Type:
5S−FE engine
4 cylinder in line, 4 cycle, gasoline
1MZ−FE engine
6 cylinder V type 4 cycle, gasoline
Bore and stroke, mm (in.):
5S−FE engine
87.0 x 91.0 (3.43 x 3.58)
1MZ−FE engine
87.5 x 83.0 (3.44 x 3.27)
Displacement, cm
3 (cu. in.):
5S−FE engine
2164 (132.0)
1MZ−FE engine
2995 (182.8)
Fuel
Fuel type:
5S−FE engine
Unleaded gasoline, Octane Rating 87
(Research Octane Number 91) or higher
1MZ−FE engine
Unleaded gasoline, Octane Rating 87
(Research Octane Number 91) or higher.
For improved vehicle performance, the
use of premium unleaded gasoline with
an Octane Rating of 91 (Research Oc-
tane Number 96) or higher is recom-
mended.
Fuel tank capacity, L (gal., Imp. gal.):
70 (18.5, 15.4)
Service specifications
ENGINE
Valve clearance (engine cold), mm (in.):
5S−FE engine
Intake 0.19—0.29 (0.007—0.011)
Exhaust 0.28—0.38 (0.011—0.015)
1MZ−FE engine
Intake 0.15—0.25 (0.006—0.010)
Exhaust 0.25—0.35 (0.010—0.014)
Spark plug type:
DENSO PK20TR11
NGK BKR6EKPB11
Spark plug gap, mm(in.):
1.1 (0.043)
Drive belt tension measured with Borroughs
drive belt tension gauge No. BT−33−73F
(used belt), Ibf:
5S−FE engine
With air conditioning
Generator belt 13010
Power steering pump belt 8020
WIthout air conditioning
Generator belt 9520
Power steering pump belt 8020
1MZ−FE engine 11520
ProCarManuals.com