fuel tank removal TOYOTA CAMRY V20 1986 Service Information

REMOVAL OF FUEL PUMP
CAUTION: Do not smoke or work near an open flame when
working the fuel pump.
1. DISCONNECT CABLE FROM NEGATIVE TERMINAL
OF BATTERY
2. REMOVE FUEL TANK
4. REMOVE FUEL PUMP FROM FUEL PUMP BRACKET
(a) Pull off the lower side of the fuel pump from the bracket.
(b) Remove the two nuts, and disconnect the wires from the fuel
pump.
(c) Disconnect the fuel hose from the fuel pump.3. REMOVE FUEL PUMP BRACKET FROM FUEL TANK
(a) Remove the bolt of the bracket.
(b) Remove the seven screws, pull out the pump bracket.
COMPONENTS (2WD)
± EFI SYSTEMFuel System (Fuel PumpFI±74

REMOVAL OF FUEL PUMP
CAUTION: Do not smoke or work near an open flame when
working the fuel pump.
1. DISCONNECT CABLE FROM NEGATIVE TERMINAL
OF BATTERY
2. REMOVE FUEL TANK
4. REMOVE FUEL PUMP±FROM FUEL PUMP BRACKET
(a) Pull off the lower side of the fuel pump from the bracket.
(b) Remove the two nuts, and disconnect the wires from the fuel
pump.
(c) Disconnect the fuel hose from the fuel pump. 3. REMOVE FUEL PUMP BRACKET FROM FUEL TANK
Remove the seven bolts, pull out the pump bracket.
COMPONENTS (4WD)
± EFI SYSTEMFuel System (Fuel Pump)FI±76

Suspension Arm
(See page RA±50)
REMOVAL OF SUSPENSION ARMS
1. JACK UP VEHICLE
Jack up the vehicle and support the body with stands.
3. DISCONNECT NO. 1 AND NO. 2 SUSPENSION ARMS
FROM AXLE CARRIER
Remove the suspension holding bolt and nut from the No. 1
and No.2 suspension arms. 2. DISCONNECT STRUT ROD FROM AXLE CARRIER
Remove the bolt and nut and disconnect the strut rod
from the axle carrier.
5. REMOVE N0.2 SUSPENSION ARM
(a) Place matchmarks on the adjusting cam and body. 4. REMOVE FUEL TANK PROTECTOR
Remove the two bolts, two clips, and the protector.
± REAR AXLE AND SUSPENSIONRear Suspension (FWD)RA±55

Strut Rod
(See page RA±50)
REMOVAL OF STRUT ROD
REMOVE STRUT ROD
(a) Remove the strut rod installation bolt and nut from the
axle carrier. 7. TORQUE STRUT ROD INSTALLATION BOLT TO AXLE
CARRIER
Torque the strut rod installation bolt to the axle carrier
with the vehicle weight on the suspension.
Torque: 1,150 kg±cm (83 ft±Ib, 113 N ± m)
8. INSTALL FUEL TANK PROTECTOR
Install the fuel tank protector with the two bolts and the
two clips.
9. CHECK REAR WHEEL ALIGNMENT(b) Torque the suspension arm installation bolt to the
axle carrier with the vehicle weight on the sus-
pension.
Torque: 1,850 kg±cm (134 ft±Ib, 181 N ± m)
(b) Remove the strut rod installation bolt and nut from the
body.
± REAR AXLE AND SUSPENSIONRear Suspension (FWD)RA±58

Strut Rod
(See page RA±50)
REMOVAL OF STRUT ROD
REMOVE STRUT ROD
(a) Remove the strut rod installation bolt and nut from the
axle carrier. 7. TORQUE STRUT ROD INSTALLATION BOLT TO AXLE
CARRIER
Torque the strut rod installation bolt to the axle carrier
with the vehicle weight on the suspension.
Torque: 1,150 kg±cm (83 ft±Ib, 113 N ± m)
8. INSTALL FUEL TANK PROTECTOR
Install the fuel tank protector with the two bolts and the
two clips.
9. CHECK REAR WHEEL ALIGNMENT(b) Torque the suspension arm installation bolt to the
axle carrier with the vehicle weight on the sus-
pension.
Torque: 1,850 kg±cm (134 ft±Ib, 181 N ± m)
(b) Remove the strut rod installation bolt and nut from the
body.
± REAR AXLE AND SUSPENSIONRear Suspension (FWD)RA±58

Stabilizer Bar
(See page RA±50)
REMOVAL OF STABILIZER BAR
1. DISCONNECT STABILIZER LINK FROM SHOCK
ABSORBER
3. REMOVE STABILIZER BAR BRACKET
(a) Remove the four bolts.
(b) Remove the stabilizer bar brackets and cushions from
the stabilizer bar.
4. DISCONNECT TANK BAND FROM BODY
(a) Using a jack and wooden block, support the fuel tank.
(b) Remove the two tank and installation bolts.
5. REMOVE STABILIZER BAR
Lower the fuel tank about 40 mm (1.57 in.) and then
remove the stabilizer bar from the body. 2. REMOVE STABILIZER BAR LINK FROM STABILIZER
BAR
± REAR AXLE AND SUSPENSIONRear Suspension (FWD)RA±60