engine TOYOTA HIGHLANDER 2020 (in English) User Guide

26
USB media port
Connecting a compatible device and cable into the USB media port will support
charging and music playback through the audio multimedia system.
Power supply switch
Charge area
Operation indicator light
Qi Wireless charger (if equipped)
A mobile device can be charged wirelessly on the tray. Push the tab and slide the
console box lid. (1) Press the power supply switch and the green operation
indicator light turns on. (2) Place a compatible mobile device on the tray as shown
in the illustration. An amber indicator illuminates while charging is in progress.
When charging is complete, the indicator illuminates green. Some phones, cases or
cover type wireless chargers may not cause the green indicator to illuminate even
though it is fully charged.
The engine switch must be in the “ACCESSORY” or ”IGNITION ON” mode for use.
Refer to the Owner’s Manual for limitations and more details on this system before
attempting to use it.
Press (1)
When the engine is turned off, the last state (ON/
OFF) of the charger is memorized.
Place device nearest the center of charging area for
best results. Moving device may result in stopping
or restarting the charging process.
Place (2)
FEATURES & OPERATIONS
63195a_MY20 Highlander.indd 2611/18/19 8:13 AM

27
OVERVIEW
FEATURES & OPERATIONS
TOYOTA SAFETY SENSE
SAFETY & EMERGENCY FEATURES
Power outlets- 12V DC
Power outlets- 120V AC (if equipped)
The engine switch must be in the “ACCESSORY” or “IGNITION ON” mode for use.
The engine switch must be in the “ACCESSORY” or “IGNITION ON” mode for use.
The engine switch must be in the “IGNITION ON” mode for use.
FrontCenter console
RearFront
USB charge-ports
(Charge only)
(Charge only)
63195a_MY20 Highlander.indd 2711/18/19 8:13 AM

32
Seat heaters/ventilators
* 12.3-inch display only
Driver and passenger seat heaters -
8-inch display
Seat heaters
Driver and passenger seat heaters -
12.3-inch display Driver and passenger seat ventilators -
8-inch display
Ventilators Driver and passenger seat ventilators -
12.3-inch display
FRONT - FRONT A/C CONTROL PANEL (IF EQUIPPED)
FRONT - TOYOTA MULTI-OPERATION TOUCH* (IF EQUIPPED)
REAR (SEAT HEATERS ONLY) (IF EQUIPPED)
The engine switch must be in the “IGNITION ON” mode for use.
FEATURES & OPERATIONS
63195a_MY20 Highlander.indd 3211/18/19 8:13 AM

33
OVERVIEW
FEATURES & OPERATIONS
TOYOTA SAFETY SENSE
SAFETY & EMERGENCY FEATURES
Steering wheel-Heater (if equipped)
The engine switch must be in the “IGNITION ON” mode for use.
* Premium Audio/12.3-inch display model
This feature utilizes the vehicle’s built-in microphone to amplify the driver’s voice
through the rear speakers. The feature must be turned on every time you enter the
vehicle, and automatically turns off when any door (including the liftgate) is opened.
There are 7 volume settings.
To activate:
(1) Select “MENU” on the Audio Multimedia System and then select “Setup”.
(2) Select “Driver Easy Speak” from “Audio” screen.
Driver Easy Speak*
63195a_MY20 Highlander.indd 3311/18/19 8:13 AM

36
FEATURES & OPERATIONSRear view monitor system
(if equipped)
The rear view monitor system displays an image of the view from the bumper of
the rear area of the vehicle. The camera for the rear view monitor system is located
above the license plate.
To adjust the image on the rear view monitor screen, press the “MENU” button and
select “Display”. Select “Camera” to adjust the screen contrast and brightness.
Refer to the Navigation and Multimedia System Owner’s Manual for limitations and
more details on this system.
Refer to section PKSB (Parking Support Brake function) in the Owner’s Manual for
limitations and more details. The Front and Rear Parking Assist with Automated Braking consists of the following
functions that operate when driving at a low speed or backing up, such as when
parking. When the system determines that the possibility of a collision with a
detected object is high, a warning operates to urge the driver to take evasive
action. If the system determines that the possibility of a collision with a detected
object is extremely high, the brakes are automatically applied to help avoid the
collision or help reduce the impact of the collision.
CHANGE SETTINGS
Use “” or “” and “” of the meter control switches to select “” and
“
” in the Multi-Information Display (MID) to change settings. The system will
continue in the last state it was in (ON or OFF) when the engine is started again.
Front and Rear Parking Assist with
Automated Braking
(if equipped)
63195a_MY20 Highlander.indd 3611/18/19 8:13 AM

39
OVERVIEW
FEATURES & OPERATIONS
TOYOTA SAFETY SENSE
SAFETY & EMERGENCY FEATURES
The Stop & Start Engine System stops and restarts the engine according to the
brake pedal operation and other operations when the vehicle is stopped.
Stopping and restarting the engine
While driving with the shift lever in
D, depress the brake pedal, and
stop the vehicle. The engine will stop
automatically.
To restart the engine, release the brake
pedal. The engine will start automatically.
Disabling the Stop & Start Engine System
Press the Stop & Start Engine System
cancel switch to disable the system.
Stop & Start Engine System (if equipped)
If the engine is stopped by the Stop & Start Engine System when the vehicle is
on an incline, brake force is temporarily maintained to prevent rolling backwards
until the engine is restarted and drive force is generated.
When drive force is generated, the maintained brake force is automatically
canceled.
Refer to the Owner‘s Manual for limitations and more details on this system before
attempting to use it.
HILL-START ASSIST CONTROL (HAC)
63195a_MY20 Highlander.indd 3911/18/19 8:13 AM

45
CHANGING PRE-COLLISION ALERT TIMING
DISABLING PRE-COLLISION SYSTEM (PCS)
FarMiddle
(default) Near
(1) Press “” or “” switches and select “” from the Multi-Information Display
(MID).
(2) Press “
” or “” switches and select “ PCS” and then press and hold “.”
(3) Press “
” or “” switches and select “Sensitivity” and then press and hold
“
” to select the desired setting. Each time it is pressed, the response to the PCS
alert timing changes as shown above.
(4) Press “
” to go back to the menu.
Note: PCS is enabled each time the engine switch is turned to Ignition On.
The system can be disabled/enabled and the alert timing of the system can be
changed. (Alert timing only, brake operation remains the same).
(1) Press “
” or “” switches and select “” from the Multi-Information
Display (MID).
(2) Press “
” or “” switches and select “ PCS” and then press and hold “.”
(3) Press “
” or “” switches and select “PCS on/off” and then press “” to
select the desired setting.
(4) Press “
” to go back to the menu.
Note: The system is enabled each time the power switch is turned to ON mode.
Refer to the Toyota Owner’s Manual for additional information on PCS operation,
settings adjustments, limitations, and precautions before attempting to use it.
OVERVIEW
FEATURES & OPERATIONS
TOYOTA SAFETY SENSE
SAFETY & EMERGENCY FEATURES
63195a_MY20 Highlander.indd 4511/18/19 8:13 AM

56
TOYOTA SAFETY SENSE™
ADJUSTING DISTANCE (CONTINUED)
Note: When your vehicle is too close to a vehicle ahead, and sufficient automatic
deceleration via the cruise control is not possible, the display will flash and the
buzzer will sound to alert the driver. An example of this would be if another driver
cuts in front of you while you are following a vehicle. Depress the brake pedal to
ensure an appropriate vehicle-to-vehicle distance.
(3) Acceleration when there are no longer any preceding vehicles driving
slower than the set speed The system accelerates until the set speed is reached. The system then
returns to constant speed cruising.
SWITCHING TO CONSTANT SPEED (CRUISE) CONTROL MODE
SETTING CONSTANT SPEED (CRUISE) CONTROL
If you are already using DRCC “”, push ON-OFF button to turn the system off
first, then push and hold ON-OFF button for at least 1.5 seconds to switch.
Note: When the engine is turned off, it will automatically default to DRCC.
Refer to the Toyota Owner’s Manual for additional information on DRCC operation,
settings adjustments, limitations, and precautions before attempting to use it.
1.5 seconds
Set
To adjust speed or cancel, see steps (2) and (3) of ADJUSTING SET SPEED on
page 54.
63195a_MY20 Highlander.indd 5611/18/19 8:13 AM

58
TOYOTA SAFETY SENSE™
Road Sign Assist (RSA)
Road Sign Assist is designed to help ensure drivers are kept informed. The RSA
system recognizes specific road signs using a forward-facing intelligent camera to
provide information to the driver via a Multi-information Display (MID). If the system
judges that the vehicle is being driven over the speed limit, or performing actions
prohibited by other support types of road signs, it alerts the driver using a warning
display and may sound a warning buzzer.
RSA DISPLAY
SUPPORTED TYPES OF ROAD SIGNS
SETTING RSA
When the driving assist system
information is selected, a maximum of
3 signs can be displayed.
Speed limit Stop
Do Not Enter Yield
When a tab other than the driving
assist system information is selected,
only a recognized speed limit sign or
do not enter sign (when notification is
necessary) will be displayed.
(1) Press “
” or “” switches and select “” from the Multi-Information Display
(MID).
(2) Press “
” or “” switches and select “ RSA” and then press and hold “.”
(3) Press “
” switches and select the “Road Sign Assist on/off” setting function
and then press “
.”
(4) Press “
” to go back to the menu.
Note: If the engine switch was last turned off while a speed limit sign was
displayed on the multi-information display, the same sign displays again when
the engine switch is turned to ON.
Refer to the Toyota Owner’s Manual for additional information on RSA operation,
settings adjustments, limitations, and precautions before attempting to use it.
63195a_MY20 Highlander.indd 5811/18/19 8:13 AM

60
SAFETY AND EMERGENCY FEATURES
Unlock
Lock
Rear door child safety locks
Tire Pressure Monitoring (warning) System (TPMS)
Moving the lever to the lock position will allow the door to be opened o\
nly from the
outside.
Rear door
Refer to the load label on the door jamb or the Owner’s Manual for tire inflation
specifications.
If the tire pressure indicator flashes for more than 60 seconds and then\
remains on,
take the vehicle to your local Toyota dealer.
NOTE: The warning light may come on due to temperature changes or
changes in tire pressure from natural air leakage. If the system has not been
initialized recently, setting the tire pressures to factory specifications should
turn off the light.
Park the vehicle in a safe place and turn the engine switch off. (Initi\
alization cannot
be performed while the vehicle is moving.) Adjust the tire inflation pr\
essure to the
specified cold tire inflation pressure level then turn the engine switch\
to ON.
System rest initialization
(1) Press “” or “” switches and select “” from the Multi-information
Display (MID).
(2) Press “
” or “” switches and select “” and then press and hold “.”
(3) Select “TPWS” and then push “
.”
(4) Select “Set Pressure” and then push and hold “
.”
“Setting Tire Pressure Warning System” will be displayed on the mu\
lti-information
display (MID) and the tire pressure warning light will blink 3 times.
When the message disappears, initialization is complete.
4.2-inch display 7-inch display
63195a_MY20 Highlander Txt.indd 6011/21/19 8:53 AM