stop start TOYOTA LAND CRUISER 1996 J80 User Guide

Q07308
AT3417
OK if hot
Add if hot
AT4252
0 − 1 mm
Q07309
DI−138
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
1996 LAND CRUISER (RM451U)
(3) With the engine OFF, add new fluid through the oil
filler pipe.
Fluid type: ATF DEXRON ®II
Capacity:
Dry fill: 11.0 liters (11.6 US qts, 9.7 Imp. qts)
Drain and refill: 1.9 liters (2.0 US qts, 1.7 Imp. qts)
(4) Start the engine and shift the shift lever into all posi-
tions from P to L position and then shift into P posi-
tion.
(5) With the engine idling, check the fluid level. Add fluid up to the COOL level on the dipstick.
(6) Check the fluid level at the normal operating tem- perature 70 − 80° C (158 − 176°F) and add as nec-
essary.
NOTICE:
Do not overfill.
(d) Check the fluid leaks.
Check for leaks in the transmission.
If there are leaks, it is necessary to repair or replace O −rings,
Seal packings, oil seals, plugs or other parts.
(e) Inspect and adjust the throttle cable. (1) Check that the throttle valve is fully closed.
(2) Check that the inner cable is not slack.
(3) Measure the distance between the outer cable endand stopper on the cable.
Standard distance: 0 − 1 mm (0 − 0.04 in.)
If the distance is not standard, adjust the cable by the adjusting
nuts.
(f) Inspect and adjust the shift lever position. When shifting the shift lever from the N position to other
positions, check that the lever can be shifted smoothly
and accurately to each position and that the position indi-
cator correctly indicates the position.
If the indicator is not aligned with the correct position, carry out
the following adjustment procedures. (1) Loosen the nut on the control rod.
(2) Push the control rod fully rearward.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Q07310Control Shaft Lever(b)
(c)
Q07311
Neutral Basic Line
Bolt
Groove
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
DI−139
1996 LAND CRUISER (RM451U)
(3) Return the control shaft lever 2 notches to N posi-
tion.
(4) Set the shift lever to N position.
(5) While holding the shift lever lightly toward the R
position side, adjust the control rod nut.
(6) Tighten the control rod nut.
Torque: 13 N·m (130 kgf·cm, 9 ft·lbf)
(7) Start the engine and make sure that the vehicle moves forward when shifting the lever from the N to
D position and reverses when shifting it to the R
position.
(g) Inspec and adjust park/neutral positoin switch. Check that the engine can be started with the shift lever
only in the N or P position, but not in other positions.
If not as stated above, carry out the following adjustment proce-
dure.
(1) Loosen the park/neutral position switch bolt and set
the shift lever to the N position.
(2) Align the groove and neutral basic line.
(3) Hold in position and tighten the bolt.
Torque: 13 N·m (130 kgf·cm, 9 ft·lbf) For continuity inspect of the park/neutral position
switch, see page DI−169 .
(h) Check the idle speed. Idle speed:
650 ± 50 rpm (In N position and air conditioner OFF)
7. MECHANICAL SYSTEM TESTS
(a) Measure the stall speed. The object of this test is to check the overall performance of the transmis\
sion and engine by measuring
the stall speeds in the D and R positions.
NOTICE:
Do the that at normal operating ATF temperature 50 − 80°C (122 − 176° F).
Do not continuously run this test longer than 5 seconds.
To ensure safety, conduct this test in a wide, clear, level area which provides good traction.
The stall test should always be carried out in pairs. One technician should\
observe the condi-
tions of wheels or wheel stoppers outside the vehicle while the other is doin\
g the test.
(1) Chock the 4 wheels.
(2) Connect an OBD II scan tool or TOYOTA hand−held tester to the DLC3.
(3) Fully apply the parking brake.
(4) Keep your left foot pressed firmly on the brake pedal.
(5) Start the engine.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

DI−140
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
1996 LAND CRUISER (RM451U)
(6) Shift into the D position. Press all the way down on the accelerator pedal wi\
th your right foot.
Quickly read the stall speed at this time.
Stall speed: 1,950 ± 150 rpm
(7) Do the same test in R position.
Stall speed: 1,950 ± 150 rpm
Evaluation:
ProblemPossible cause
Stall speed low in D and R positions
 Engine output may be insuf ficient
 Stator one− way clutch is operating properly
HINT:
If more than 600 rpm below the specified value, the torque con-
verter clutch could be faulty.
Stall speed high in D position
 Line pressure too low
 Forward clutch slipping
 No. 2 one− way clutch not operating properly
 O/D one− way clutch not operating properly
Stall speed high in R position
Line pressure too low
 Direct clutch slipping
 1st and reverse brake slipping
 O/D clutch slipping
Stall speed high in D and R positions
Line pressure too low
 Improper fluid level
 O/D one− way clutch not operating properly
(b) Measure the time lag.
When the shift lever is shifted while the engine is idling, there will be a certain time lapse o\
r lag before
the shock can be felt. This is used for checking the condition of the O/D d\
irect clutch, forward clutch,
direct clutch and 1st and reverse brake.
NOTICE:
Do the test at normal operating ATF temperature 50 − 80°C (122 − 176° F).
Be sure to allow 1 minute interval between tests.
Take 3 measurements and take the average value.
(1) Fully apply the parking brake.
(2) Start the engine and check idle speed.
Idle speed: 650 ± 50 rpm (In N position and air conditioner OFF)
(3) Shift the shift lever from N to D position. Using a stop watch, measure the ti\
me it takes from shift-
ing the lever until the shock is felt.
In the same manner, measure the time lag for N → R.
Time lag: N → D Less than 1.2 seconds
In the same way, measure the time lag for N → R.
Time lag: N → R Less than 1.5 seconds
If N → D time or N → R time lag is longer than specified:
Evaluation:
ProblemPossible cause
N → D time lag is longer
Line pressure too low
 Forward clutch worn
 O/D one− way clutch not operating properly
N → R time lag is longer
Line pressure too low
 Direct clutch worn
 1st and reverse brake worn
 O/D one− way clutch not operating properly
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

−
DIAGNOSTICS AUTOMATIC TRANSMISSION
DI−141
1996 LAND CRUISER (RM451U)
8. HYDRAULIC TEST
Measure the line pressure.
NOTICE:
Do the test at normal operation ATF temperature 50 − 80°C (122 − 176° F).
The line pressure test should always be carried out in pairs. One techni\
cian should observe
the conditions of wheels or wheel stoppers outside the vehicle while the ot\
her is doing the test.
Be careful to prevent SST’s hose from interfering with the exhaust pipe.
(1) Warm up the ATF.
(2) Remove the test plug on the transmission case right side and connect SST\
(See page AT−18
for the location to connect SST).
SST 09992 −00094 (09992 −00150, 09992−00270)
(3) Fully apply the parking brake and chock the 4 wheels.
(4) Start the engine and check idling speed.
(5) Keep your left foot pressed firmly on the brake pedal and shift into D p\
osition.
(6) Measure the line pressure when the engine is idling.
(7) Press the accelerator pedal all the way down. Quickly read the highest line pr\
essure when engine
speed reaches stall speed.
NOTICE:
Release the accelerator pedal and stop test if the rear wheels begin to rotate before the engine speed
reaches the specified stall speed.
(8) In the same manner, do the test in R position.
Specified line pressure:
Condition D position kPa (kgf/cm2, psi) R position kPa (kgf/cm2, psi)
Idling422 −
481 (4.3 − 4.9, 61 − 70)510 − 608 (5.2 − 6.2, 74 − 88)
Stall1,285 − 1,530 (13.1 − 15.6, 128 − 153)1,579 − 1,932 (16.1 − 19.7, 158 − 193)
If the measured pressures are not up to specified values, recheck the thro\
ttle cable adjustment and retest.
Evaluation:
ProblemPossible cause
If the measured value at all positions are higher
Throttle cable out of adjustment
 Throttle valve defective
 Regulator valve defective
If the measured value at all positions are lower
Throttle cable out of adjustment
 Throttle valve defective
 Regulator valve defective
 Oil pump defective
 O/D direct clutch defective
If pressure is low in the D position onlyD position circuit fluid leakage
 Forward clutch defective
If pressure is low in the R position only
R position circuit fluid leakage
 Direct clutch defective
 1st and reverse brake defective
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

−
DIAGNOSTICS AUTOMATIC TRANSMISSION
DI−149
1996 LAND CRUISER (RM451U)
Harsh engagement (N
→ D)
1. Shift solenoid valve SL circuit
2. ATF temp. sensor circuit
3. Throttle position sensor circuit
4. Park/neutral position switch circuit
5. On −vehicle repair matrix chart
6. Off −vehicle repair matrix chart
7. ECMDI−163
DI−154 DI−35
DI−169 −
−
DI−145
Harsh engagement (Lock −up)
1. Shift solenoid valve SL circuit
2. Throttle position sensor circuit
3. No. 1 vehicle speed sensor circuit
4. No. 2 vehicle speed sensor circuit
5. On −vehicle repair matrix chart
6. Off −vehicle repair matrix chart
7. ECMDI−163 DI−35
DI−87
DI−166 −
−
DI−145
Harsh engagement (Any driving position)
1. Shift solenoid valve SL circuit
2. ATF temp. sensor circuit
3. Throttle position sensor circuit
4. No. 1 vehicle speed sensor circuit
5. No. 2 vehicle speed sensor circuit
6. On −vehicle repair matrix chart
7. Off −vehicle repair matrix chart
8. ECMDI−163
DI−154 DI−35
DI−87
DI−166
−
−
DI−145
Slip or shudder (Forward and reverse)1. On −vehicle repair matrix chart
2. Off −vehicle repair matrix chart−
−
Slip or shudder (A particular position)1. On −vehicle repair matrix chart
2. Off −vehicle repair matrix chart−
−
No engine braking1. On −vehicle repair matrix chart
2. Off −vehicle repair matrix chart−
−
Poor acceleration
1. Throttle position sensor circuit
2. No. 1 vehicle speed sensor circuit
3. No. 2 vehicle speed sensor circuit
4. Shift solenoid valve No. 1 and No. 2 circuit
5. Shift solenoid valve SL circuit
6. On −vehicle repair matrix chart
7. Off −vehicle repair matrix chartDI−35
DI−87
DI−166
DI−157
DI−163 −
−
No kick− down
1. Throttle position sensor circuit
2. Shift solenoid valve No. 1 and No. 2 circuit
3. No. 1 vehicle speed sensor circuit
4. On−vehicle repair matrix chart
5. ECMDI−35
DI−157 DI−87 −
DI−145
No pattern select1. Pattern select switch circuit
2. ECMDI−179
DI−145
No 2nd start
1. Pattern select switch circuit
2. Shift solenoid valve No. 1 and No. 2 circuit
3. ECMDI−179
DI−157
DI−145
Large shift shock or engine stalls when starting off or stopping
1. Shift solenoid valve SL circuit
2. Stop light switch circuit
3. Off −vehicle repair matrix chart
4. ECMDI−163
DI−185 −
DI−145
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

DI−152
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
1996 LAND CRUISER (RM451U)
Slip or shudder (R position)
1. Direct clutch (C2)
2. 1st and reverse brake (B
3)
3. O/D one− way clutch (F
0)



Slip or shudder (1st)
1. Forward clutch (C1)
2. No. 2 one− way clutch (F
2)
3. O/D one− way clutch (F
0)



Slip or shudder (2nd)
1. 2nd brake (B2)
2. 2nd coast brake (B
1)
3. No. 1 one− way clutch (F
1)



Slip or shudder (3rd)1. Direct clutch (C2)
Slip or shudder (O/D)1. O/D brake (B0)
No engine braking (1st − 3rd)1. O/D direct clutch (C0)
No engine braking (1st)1. 1st and reverse brake (B3)
No engine braking (2nd)1. 2nd coast brake (B1)
Poor acceleration (All positions)1. Torque converter clutchAT −26
Poor acceleration (O/D)1. O/D brake (B0)
2. O/D planetary gear unit

Poor acceleration (Other than O/D)1. O/D brake (B0)
Poor acceleration (Other than 2nd)1. 2nd coast brake (B1)
2. No. 1 one− way clutch (F
1)


Poor acceleration (1st and 2nd)1. O/D one−way clutch (F0)
Poor acceleration (L and R positions)1. 1st and reverse brake (B3)
Poor acceleration (R position)1. Forward clutch (C1)
Engine stalls when starting off or stopping1. Torque converter clutchAT−26
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Position
NORMALSHIFT SOLENOID NO. 1
MALFUNCTIONING
Solenoid valve
No. 1 No. 2GearSHIFT SOLENOID NO. 2
MALFUNCTIONING
BOTH SOLENOIDS MAL-
FUNCTIONINGSolenoid valve
No. 1 No. 2 GearSolenoid valve
No. 1 No. 2 GearGear when shift selector is
manually operated
D
2
LON
ON
OFF
ON
ON
OFF
OFF OFF
ON
ON OFF
ON
ON
OFF
ON
ON ON OFF 1st
2nd
3rd
O/D
1st
2nd
3rd
1st
2nd X
X
X
X
X
X
X
X
X
ON
ON
OFF
OFF ON
ON
ON
3rd 3rd
O/D
3rd
3rd
1st
2nd X
X
X
X
X
X
X
X
XOFF
OFF
ON
ON OFF OFF
OFF
ON
ON
1st
O/D
3rd 1st O/D O/D
3rd
1st
1st
O/D O/D O/D
O/D
3rd 3rd
3rd
1st
1st
X: Malfunctions ON
ON
3rd
3rd
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
DI−157
1996 LAND CRUISER (RM451U)
DTC P0753, P0758 Shift Solenoid A/B Electrical Malfunc-
tion (Shift Solenoid Valve No. 1/No. 2)
CIRCUIT DESCRIPTION
Shifting from 1st to O/D is done in combination with ON and OFF of the shift solenoid valves No. 1 and No\
.
2 controlled by ECM. If an open or short circuit occurs in either of the \
shift solenoid valves, the ECM controls
the remaining normal shift solenoid valve to allow the vehicle to be operat\
ed smoothly (Fail safe function).
Fail Safe Function:
If either of the shift solenoid valve circuits develops an open or short, \
the ECM turns the other shift solenoid
ON and OFF to shift to the gear positions shown in the table below. The ECM also turns the shift solenoid
valve SL OFF at the same time. If both solenoids are malfunction, hydraulic contr\
ol cannot be done electroni-
cally and must be done manually.
Manual shifting as shown in the following table must be done (In the case of a short circuit, the E\
CM stops
sending current to the short circuited solenoid).
HINT:
Check the shift solenoid valve No. 1 when DTC P0753 is output and check \
the shift solenoid valve No. 2
when DTC P0758 is output.
DTC No.DTC Detecting ConditionTrouble Area
P0753
P0758
The ECM checks for an open or short circuit in the shift sole-
noid valves No. 1 and No. 2 circuit when it changes
The ECM records DTC P0753 or P0758 if condition (a) or (b) is
detected once, but it does not light up MIL
After ECM detects condition (a) or (b) continuously 8 times or
more in one− trip, it causes the MIL light up until condition (a) or
(b) disappears
After that, if the ECM detects condition (a) or (b) once, it starts
lighting up MIL again
(a) Solenoid resistance is 8 Ω or less (short circuit) when the
solenoid is energized
(b) Solenoid resistance is 100 k Ω or more (open circuit) when
the solenoid is not energized
 Open or short in shift solenoid valve No. 1/No. 2 circuit
 Shift solenoid valve No. 1/No. 2
 ECM
DI5KO−02
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

N09348
Interface BoxHarness VehicleTOYOTA
Tester
Hand
−held
TOYOTA Break −out− box
F00007
DLC1
Ts Tc
E
1
BR3904
0.25 sec. 0.25 sec.
ON
OFF
DI−192
−
DIAGNOSTICS ANTI−LOCK BRAKE SYSTEM
1996 LAND CRUISER (RM451U)
(d) Using TOYOTA break −out− box and TOYOTA hand− held
tester, measure the ECU terminal values.
(1) Hook up the T OYOTA hand−held tester and TOYO-
TA break−out−box to the vehicle.
(2) Read the ECU input/output values by following the prompts on the tester screen.
HINT:
TOYOTA hand −held tester has a ”Snapshot ” function. This re-
cords the measured values and is effective in the diagnosis of
intermittent problems.
Please refer to the TOYOTA hand−held tester/TOYOTA break
out−box operators manual for further details.
2. SPEED SENSOR SIGNAL AND DECELERATION SEN-
SOR CHECK
(a) Check the speed sensor signal. (1) Conform that the center differential is free.
(2) Turn the ignition switch OFF.
(3) Using SST, connect terminals Ts and E
1 of the
DLC1.
SST 09843−18020
(4) Start the engine.
(5) Check that the ABS warning light blinks.
HINT:
If the ABS warning light does not blink, inspect the ABS warning
light circuit (See page DI−230).
(6) Drive vehicle straight forward.
HINT:
Drive vehicle faster than 45 km/h (28 mph) for several seconds.
(7) Stop the vehicle.
(8) Using SST, connect terminals Tc and E
1 of the
DLC1.
SST 09843−18020
(9) Read the number of blinks of the ABS warning light.
HINT:
See the list of DTC on page DI−190 .
If every sensor is normal, a normal code is output (A cycle of
0.25 sec. ON and 0.25 sec. OFF is repeated).
If 2 or more malfunction are indicated at the same time, the low-
est numbered code will be displayed 1st.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

N14305
(1)
(1) (2)
No.
Operation Method CRUISE MAIN Indicator Light
Blinking Pattern Diagnosis
1 Turn SET/COAST switch ON
2 Turn RES/ACC switch ON
3 Turn CANCEL switch ON
Turn stop light switch ON
Depress brake pedal
Turn PNP switch OFF
(Shift to except D position)
4 Drive at about 40 km/h
(25 mph)or higher
Drive at about 40 km/h
(25 mph) or below
Light
ON
OFF
Light ON
OFF
Light ON
OFF Switch ON
Switch OFF
LightON
OFF Switch OFF
Switch ONSET/COAST switch circuit
is normal
RES/ACC switch circuit
is normal
CANCEL switch circuit
is normalStop light switch circuit
is normal
PNP switch circuit is
normal
Vehicle Speed Sensor is
normal
Light ON
OFF
Light
ON
OFF
1sec.
0.25 sec. 0.25 sec.
-
DIAGNOSTICS CRUISE CONTROL SYSTEM
DI-290
1996 LAND CRUISER (RM451U)
5. INPUT SIGNAL CHECK
HINT:
(1) For check No.1 - No.3

Turn ignition switch ON.
(2) For check No.4

Jack up the vehicle.

Start the engine.

Shift to D position.
(a) Press the control switch to SET/COAST or RES/ACC position and hold it down or hold it up º1º.
(b) Push the main switch ON º2º.
(c) Check that the CRUISE MAIN indicator light blinks twice or 3 times repeatedly after 3 seconds.
(d) Turn the SET/COAST or RES/ACC switch OFF.
(e) Operate each switch as listed in the table below.
(f) Read the blinking pattern of the CRUISE MAIN indicator light.
(g) After performing the check, turn the main switch OFF.
HINT:
When 2 or more signals are input to the ECU, the lowest num-
bered code will be displayed first.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

FI1654
Fulcrum Length
30 cm
SST
−
SFI SFI SYSTEM
SF−3
631
Author: Date:
1996 LAND CRUISER (RM451U)
8. FUEL SYSTEM
(a) When disconnecting the high fuel pressure line, a large
amount of gasoline will spill out, so observe the following
procedures:
(1) Disconnect the fuel pump connector.
(2) Start the engine. After the engine has stopped onits own, turn off the ignition switch.
(3) Put a container under the connection.
(4) Slowly loosen the connection.
(5) Disconnect the connection.
(6) Plug the connection with 2 rubber plugs.
(7) Reconnect the fuel pump connector.
(b) When connecting the union bolt on the high pressure pipe
union, observe the following procedures:
(1) Always use a new gasket.
(2) Tighten the union bolt by hand.
(3) Tighten the union bolt to the specified torque.
Torque: 29 N·m (300 kgf·cm, 21 ft·lbf)
(c) When connecting the flare nut on the high pressure pipe union, observe the following procedures:
(1) Apply a light coat of engine oil to the flare and tight-
en the flare nut by hand.
(2) Using SST, tighten the flare nut to the specified torque.
SST 09631−22020
NOTICE:
Do not rotate the fuel pipe, when tightening the flare nut.
Torque: 30 N·m (310 kgf·cm, 22 ft·lbf)
HINT:
Use a torque wrench with a fulcrum length of 30 cm (11.81 in.).
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010