change time TOYOTA LAND CRUISER 2007 J200 Navigation Manual

i
Introduction
Thank you for your purchase of the Navigation System. Please read this manual carefully to ensure proper use. Keep this manual
in your vehicle at all times.
The Navigation System is one of the most technologically advanced vehicle accessories ever developed. The system receives satellite signals
from the Global Positioning System (GPS) operated by the U.S. Department of Defense. Using these signals and other vehicle sensors, the
system indicates your present position and assists in locating a desired destination.
The navigation system is designed to select efficient routes from your present starting location to your destination. The system is designed
to direct you to a destination that is unfamiliar to you in an efficient manner. The system uses the maps of DENSO. The calculated routes
may not be the shortest nor the least traffic congested. Your own personal local knowledge or “short cut” may at times be faster than the calcu-
lated routes.
The navigation system’s database includes about 75 Point of Interest categories to allow you to easily select destinations such as restaurants
and banks. If a destination is not in the database, you can enter the street address or a major intersection close to it and the system will guide
you there. The system will provide both a visual map and audio instructions. The audio instructions will announce the distance remaining
and the direction to turn in approaching a fork or intersection. These voice instructions will help you keep your eyes on the road and are timed
to provide enough time to allow you to maneuver, change lanes or slow down.
Please be aware that all current vehicle navigation systems have certain limitations that may affect their ability to perform properly.
The accuracy of the vehicle’s position depends on the satellite condition, road configuration, vehicle condition or other circumstan-
ces. For more information on the limitations of the system, refer to pages x through xii.

vi
1Northup or headingup symbol
This symbol indicates a map view with
north−up or heading−up. Touching this sym-
bol changes the map orientation. ix. . . . . . .
2Scale indicator
This figure indicates the map scale. viii. . .
3GPS mark (Global Positioning Sys-
tem)
Whenever your vehicle is receiving signals
from the GPS, this mark is displayed.
x . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4Distance and time to destination
Displays the distance and the estimated
travel time to the destination. lxvii. . . . . . . .
5Zoom out switch
Touch this switch to reduce the map scale.
viii . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6“Mark” switch
Touch this switch to register the cursor posi-
tion as a memory point. vi. . . . . . . . . . . . . . .
7“Route” switch
Touch this switch to change the route.
liii, lv . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
— Quick reference

ix
7“Map” switch
You can select a destination simply by
touching the location on the displayed map.
xlv . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8“Intersection” switch
You can enter the names of two intersecting
streets. This is helpful if you do not know the
specific street address of your destination
but know the general vicinity. xlv. . . . . . . . .
9“Freeway Ent./Exit” switch
You can enter the name of a freeway (inter-
state) entrance or exit. xlvi. . . . . . . . . . . . . .
10“Phone #” switch
You can enter a destination by the telephone
number. xlviii. . . . . . . . . . . . . . . . . . . . . . . . .
11“Coordinates” switch
You can set a destination using latitude and
longitude as coordinates. xlvii. . . . . . . . . . .
12Quick access switch
You can select one of 5 preset destinations
directly. To use this function, it is necessary
to set the “Attribute” for each memory point.
(To register a “Quick Access”, see page
lxxxi.)
xxxii . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13Home switch
You can select your own home without en-
tering the address each time. To use this
function, it is necessary to set the “Attribute”
for the memory point. (To register “Home”,
see page lxxxi.) xxxii. . . . . . . . . . . . . . . . . .
14“Change” switch
To change the search area, touch this
switch.
xxx . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

xii
(b) Inappropriate route guidance
may occur in the following cases:
When turning at an intersection off the
designated route guidance.
If you set more than one destination but
skip any of them, auto reroute will display a
route returning to the destination on the pre-
vious route.
When turning at an intersection for which
there is no route guidance.
When passing through an intersection
for which there is no route guidance.
During auto reroute, the route guidance
may not be available for the next turn to the
right or left.
It may take a long time to operate auto re-
route during high speed driving. In auto re-
route, a detour route may be shown.
After auto reroute, the route may not be
changed.
An unnecessary U−turn may be shown
or announced.
A location may have multiple names and
the system will announce one or more.
Some routes may not be searched.
If the route to your destination includes
gravel, unpaved roads or alleys, the route
guidance may not be shown.
Your destination point might be shown on
the opposite side of the street.
When a portion of the route has regula-
tions prohibiting the entry of the vehicle that
vary by time or season or other reason.
The road and map data stored in your
navigation system may not be complete or
may not be the latest version.
After replacing the tire, implement the
operation described in the “ Tire
change calibration”. (For details, see
page xc.)
This navigation system uses the tire turning
data and is designed to work with factory−
specified tires for your vehicle. Installing
tires that are larger or smaller than the origi-
nally equipped diameter may cause inaccu-
rate display of the vehicle’s position. The tire
pressure also affects the diameter of the
tires so please make sure the tire pressure
of all four tires is correct.
Map database information
and updates
This system uses the maps of DENSO.

lxi
Touch the switch of your desired Point of In-
terest. Selected Points of Interest are dis-
played on the map screen.
“Dist.”: To sort in the order of distance from
your current location.
“Icon”: To sort in the order of the POI icons.
“Name”: To sort in alphabetical order by
name.
“On Route”: When the indicator is illumi-
nated by touching this switch, the list of the
items searched along the route is displayed.
To set a POI as a destination
You can select one of the Points of Interest
icons on the map screen as a destination
and use it as route guidance.
Directly touch the Point of Interest icon
that you wish to set as a destination.
The map will shift so that the icon is centered
on the screen and overlaps with the cursor
. At this time, the distance from your cur-
rent position can be displayed on the screen.
The distance shown is measured as a
straight line from the current vehicle position
to the POI.
When your desired Point of Interest over-
laps with the cursor, touch the
“Enter
” switch. The screen changes and dis-
plays the map location of the selected
destination and route preference. (See “
— Entering destination” on page xlviii.)
Route overview
1. Touch the “Map View” switch.
2. Touch the “Route Overview”switch.

lxviii
2. Touch the number switch of the des-
tination you wish to display.
The distance and the estimated travel time
from the current position to the selected des-
tination are displayed.
Displayed while driving along the
guidance route.
Displayed while driving off the
guidance route. The destination
direction is indicated by an arrow.
INFORMATION
When the vehicle is on the guidance
route, the distance measured along the
route is displayed. Travel time is calcu-
lated based on the set vehicle speed in-
formation. (For details, see page xci.)
However, when the vehicle is not on the
guidance route, the distance is the lin-
ear distance between the current posi-
tion and the destination.
Foot print map
For the area which is covered by the foot
print map (Some areas in the following cit-
ies; Detroit, Chicago, N.Y., L.A), you can
switch to the foot print map on a scale of 75
feet (25 m).
To switch to the foot print map
The
switch changes into the
switch when the map is scaled down to 150
feet (50 m).
To display the foot print map, touch the
switch.
To delete the foot print map display
Touch the
switch.

lxxii
ADVANCED FUNCTIONS
Descriptions of functions for more effective use
Suspending and resuming guidancelxxiii . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Volumelxxiv . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
User selectionlxxiv . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
My placeslxxvii . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Area to avoidlxxxiv . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setuplxxxvii . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Current position calibrationlxxxviii . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Distance unitxc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Estimated travel timexci . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Auto reroutexcii . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Adjusting time zonexciii . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Auto voice guidancexciv . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Voice guidance in all modesxcv . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Notifying traffic restrictionxcvi . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Intersection guidancexcvii . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Guidance screen on freewayxcviii . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Street name on scroll mapxcix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Display of building shapec . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Screen layout functionci . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
POI category change (Show POI Icons)ci . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Delete previous pointciii . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Map colorciv . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Screen animationcv . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION III

xciii
3. Touch the “On” switch of “Auto
Reroute”.
The selected switch is highlighted in green.
INFORMATION
If your vehicle strays from the guidance
route, the system searches for a new
route to the destination. The new route
may or may not take you back to the
previous route depending on how far
you are off the original guidance route.
Adjusting time zone
1. Push the “MENU” button.
2. Touch the “Setup” switch.
3. Touch the “Change” switch. The
“Adjust Time Zone” screen appears on
the display.

cv
Screen animation
When the “Screen Animation” feature is
turned on, some switches and screens
become animated. (e.g.: change map
guidance on the map screen)
To turn the “Screen Animation” mode on:
1. Push the
“MENU” button.
2. Touch the “Setup” switch. Then
touch
switch three times to display
page 4 of the “Setup” screen.
3. Touch the “On” switch of “Screen
Animation” and touch the
“OK” switch.

cviii
Maintenance information
This system informs you when to replace
certain parts or components and shows
dealer information (if registered) on the
screen. (See “Information items” on
page cix.) When the navigation system
begins operating after either the informa-
tion item’s preset data arrives or the
driving distance reaches a predeter-
mined setting, the “Information” screen
will be displayed. This screen will appear
every time the system is turned on until
you touch the
“Do not display this
message again”
switch.
To prevent this information screen from be-
ing displayed again, touch the
“Do not
display this message again”
switch.1. Push the
“INFO” button to display
the “Information Menu” screen and
touch the
“Maintenance” switch.
5u004
2. Touch the desired icon and input the
conditions.
Notice of “Date”: You can input the next
maintenance date.
Notice of “Distance”: You can input the
driving distance until the next maintenance
check.
When you touch the
switch on the
“Maintenance” screen, the screen changes
to the “Personal Event” screen. Touch the
keys to input the desired name and then in-
put conditions.
After you input the date and/or distance,
touch the
“OK” switch. The screen then
returns to the “Maintenance” screen.
The following switches appear.
“Delete All”: To cancel all conditions which
have been inputted.