ignition TOYOTA LAND CRUISER 2007 J200 Navigation Manual

ii
Important information about this manual
For safety reasons, this manual indicates
items requiring particular attention with the
following marks.
CAUTION
This is a warning against anything
which may cause injury to people if the
warning is ignored. You are informed
about what you must or must not do in
order to reduce the risk of injury to
yourself and others.
NOTICE
This is a warning against anything
which may cause damage to the ve-
hicle or its equipment if the warning is
ignored. You are informed about what
you must or must not do in order to
avoid or reduce the risk of damage to
your vehicle and its equipment.
INFORMATION
This provides additional information.
Initial screen
When you start the engine or turn the ignition
switch to the “ACC” position, the initial
screen appears and the system begins
operating.
CAUTION
When the vehicle is stopped with the
engine running, always apply the park-
ing brake for safety.
After a few seconds, the “CAUTION” screen
appears.

cxx
Trip information
Trip information such as driving time,
driving distance, average vehicle speed,
fuel consumption, etc. can be displayed
on the screen.
1. Push the
“INFO” button to display
the information menu screen.
5u004
2. Touch the “Trip Information”switch.
Consumption
The consumption is calculated and dis-
played based on the driving distance and
the fuel consumption for 2 seconds with
engine running.
The value is updated every 2 seconds.
If you are driving at low speeds just before
stopping, the accurate figure way not be
shown.
After Refueling
The consumption after refueling is calcu-
lated and displayed based on the total
driving distance and the total fuel con-
sumption after refueling.
The value is updated every 10 seconds.
When refueling, be sure to stop your vehicle
and turn the ignition switch off.Cruising Range
How far you can drive with the remaining
fuel is displayed.
Even though the display indicates sufficient
miles to run, if the fuel level on the fuel gauge
approaches “E” or the low fuel level warning
light comes on, fill the fuel tank as soon as
possible.
INFORMATION
When you first start driving your new
vehicle, the correct cruising range
may not be shown. One or more re-
fills of 10 gallons or more may be re-
quired for the system to set its cal-
ibration.
The cruising range displayed is cal-
culated based on past fuel con-
sumption and may vary according to
your driving style and road condi-
tion.

cxxi Average Speed
The Average Speed is displayed. The av-
erage vehicle speed is calculated and
displayed based on the total driving dis-
tance and the total driving time after the
engine is started.
The displayed value is updated every 10
seconds.
To calculate from the beginning, touch the
“Reset” switch.
Distance
The distance after engine starting is dis-
played.
When refueling, be sure to stop your vehicle
and turn the ignition switch off.
Handsfree system
Handsfree system allows you to make
or receive a call without taking your
hands off the steering wheel by connect-
ing your cellular phone.
This system supports the Bluetooth.
Bluetooth is a wireless data system by
which you can call without your cellular
phone connecting with a cable or placing on
a cradle.
If your cellular phone does not support the
Bluetooth, this system can not function.
CAUTION
While you are driving, do not use a cel-
lular phone or connect the Bluetooth
phone.
NOTICE
Do not leave your cellular phone in
the car. The temperature indoor may
be high and damage the phone.
INFORMATION
In the following conditions, the sys-
tem may not function.
The cellular phone is turned OFF.
The current position is outside the
communication area.
The cellular phone is not connected.
The cellular phone has a low battery.

cxxvi
Connect the Bluetooth phone
When you turn the ignition key to “ACC”
or “ON”, the selected Bluetooth phone
will be automatically connected and the
connection result is displayed.
Leave the Bluetooth phone enable to con-
nect.
This screen appears when the Bluetooth
phone is first connected after you turn the
ignition key to “ACC” or “ON”.
Reconnect the Bluetooth phone
If the Bluetooth phone is disconnected
with a poor reception from the Blue-
tooth network when the ignition key is
turned to “ACC” or “ON”, the system au-
tomatically reconnects the Bluetooth
phone. In this case, the connection result
is not displayed.
If the Bluetooth is disconnected on purpose
such as you turned your cellular phone OFF,
this does not happen. Reconnect it by the
following methods.
Select the Bluetooth phone again.
Enter the Bluetooth phone.
Confirm the Bluetooth information
You can confirm or change the detail set-
ting of the Bluetooth phone.
Touch the “Settings” of Bluetooth to
display “Bluetooth* Information” screen.
*: Bluetooth is a trademark owned by Blue-
tooth SIG. Inc.

cxlvii The automatic air conditioning auto-
matically maintains the set tempera-
ture.
This air conditioning features automatic
fan speed and air flow control which auto-
matically selects the most suitable fan
speed and air flow to control the tempera-
ture. The ignition key must be in the “ON”
position.
CLIMATE: Push this button to display
switches for automatic air conditioning con-
trols.
NOTICE
To prevent the battery from being dis-
charged, do not leave the air condi-
tioning on longer than necessary
when the engine is not running.
oxu002
By pushing the switch above, you can
operate the speech command system.
For the operation of the speech command
system and the command, see page cxxxix
and cxli.
(a) Climate control
SETTING OPERATION automatic con-
trol
1. Push the “AUTO” button.
Air flow quantity, switching of the diffusers,
on−off of the air conditioning, and switching
of the air intake between RECIRCULATED
AIR and OUTSIDE AIR are automatically
adjusted. The operation status is shown by
each indicator.
When one of the manual control buttons is
depressed while operating in automatic
mode, the mode relevant to the depressed
button is set. Other conditions continue to
be adjusted automatically.
Push the “OFF” button to turn the air condi-
tioning off.

clvi
Using your audio system:
some basics
This section describes some of the basic
features of the Toyota audio system. Some
information may not pertain to your system.
Your audio system works when the ignition
key is in the “ACC” or “ON” position.
NOTICE
To prevent the battery from being
discharged, do not leave the car
audio on longer than necessary when
the engine is not running.
oxu002
By pushing the above button, you can
operate the speech command system.
For the operation of the speech command
system and the command, see page cxxxix
and cxli.
(a) Turning the system on and off
UNX602
POWERVOL: Push this knob to turn the
audio system on and off. Turn this knob to
adjust the volume. The system turns on in
the last mode used.
AUDIO: Push this button to display switches
for audio system.
VI

clxxii
7ulc010a
“Automatic program selection” button:
The automatic program selection feature al-
lows you to program your cassette player to
skip forward or backward to locate the song
you want to hear. You can skip up to 9 pro-
grams at a time.
Push this button on the upper side to skip for-
ward. “FF” and the number will appear on
the display. Push the button until the number
you want to skip appears on the display. Af-
ter that, the player will automatically skip for-
ward.
When the end of the tape is reached, the
player automatically reverses sides and re-
sumes normal play.
Push this button on the lower side to skip
backward. Push the button until “REW” and
the number you want to skip appear on the
display.
If you set “REW 1”, the player will rewind
to the beginning of the current program.
When counting the number of programs
you want to rewind, remember to count the
current program as well. For example, if you
want to rewind to a song that is two before
the song you are listening to, push this but-
ton until “REW 3” appears on the display.
When the beginning of the tape is reached,
the player automatically resumes normal
play.
There must be at least 5 seconds of blank
space between programs for this feature to
work correctly.
“RPT”, “SKIP” or “Automatic program
selection” features: These features may
not work well with some spoken word, live or
classical recordings.
DVD player operation
The DVD player can play audio CDs, DVD
video discs and video CDs.
For appropriate discs for this paper, see “Car
audio/video system operating hints” on page
clxxxix.
For safety reasons, you can enjoy DVD vid-
eo discs and video CDs only when the ve-
hicle is completely stopped with the ignition
switch in the “ACC” or “ON” position and the
parking brake applied. While you are driving,
you can hear audio alone even in the DVD
video or video CD mode.
The DVD player can play the discs labeled
as shown below.
VI

clxxviii
The “DVD Hint !” screen appears when
the video screen is first displayed after
you turn the ignition key to “ACC” or
“ON”.
Touch the “OK” switch when you read the
message.(i) Playing a DVD video disc
lxb009a
Push the “AUDIO” button to display this
screen. You can operate the switches
and choose the number of the disc you
want to play. The selected disc is auto-
matically played.
When you touch the “WIDE MODE” switch,
the screen mode can be changed.
When you touch the “PICTURE” switch, the
video screen returns.(ii) Displaying operation switches