coil spring TOYOTA SEQUOIA 2001 Service Owner's Manual

SA176±04
SA±142
± SUSPENSION AND AXLECOIL SPRING AND REAR SHOCK ABSORBER
3138 Author: Date:
2005 SEQUOIA (RM1146U)
INSTALLATION
Installation is in the reverse order of removal (See page SA±137).

F13256

Non±reusable part
Molybdenum disulfide lithium base grease
: Specified torqueN´m (kgf´cm, ft´lbf)Column Upper
Bracket
Key Cylinder Key Unlock
Warning Switch
Ignition Switch
10.5 (110, 8)
Column Tube
Assembly
2.2 (23, 19 in.´lbf)

Spring Guide


Tilt Spring Main Shaft Assembly Steering Column Housing
Tilt Lever Release Lever SpringTurn Signal Bracket

Compression
SpringSpring
Retainer Upper Bearing Inner Race Seat
Inner Race

12 (120, 9)
Pivot Pin
Spring
Park Lock Cable
Assembly
Shaft Bearing
Main Shaft Stopper
Pivot Pin Shift Lever
Housing
18 (180, 13)



Shift Lever
No. 2 Steering Column Ring

Tilt Lever Lock Shaft9.0 (90, 78 in.´lbf)





7.5 (75, 65 in.´lbf)
2.9 (29, 25 in.´lbf)
Transponder Key Coil
Key Cylinder
Lamp Assembly
Screw
Transponder Key Amplifier
Tilt No. 1
Stopper
± STEERINGTILT STEERING COLUMN
SR±13
3240 Author: Date:
2005 SEQUOIA (RM1146U)

SR0V1±06
F13611
Screw Extractor
F06733
± STEERINGTILT STEERING COLUMN
SR±17
3244 Author: Date:
2005 SEQUOIA (RM1146U)
DISASSEMBLY
NOTICE:
When using a vise, do not overtighten it.
1. REMOVE TRANSPONDER KEY COIL
2. REMOVE KEY CYLINDER LAMP ASSEMBLY
3. REMOVE COLUMN UPPER BRACKET
(a) Using a centering punch, mark the center of the 2 ta-
pered±head bolts.
(b) Using a 3 to 4 mm (0.12 to 0.16 in.) drill, drill a hole into
the 2 bolts.
(c) Using a screw extractor, remove the 2 bolts and column
upper bracket.
4. REMOVE SHIFT LEVER
Using a torx® socket wrench, remove the torx® screw and shift
lever.
5. REMOVE PARK LOCK CABLE ASSEMBLY
(See page AT±20)
6. REMOVE SHIFT LEVER HOUSING
Using a torx® socket wrench, remove the 3 torx® screws and
shift lever housing.
7. REMOVE RELEASE LEVER SPRING
8. REMOVE TURN SIGNAL BRACKET
Using a torx® socket wrench, remove the 2 torx® screws and
turn signal bracket.

F06737
F13612
SR±22
± STEERINGTILT STEERING COLUMN
3249 Author: Date:
2005 SEQUOIA (RM1146U)
7. INSTALL TURN SIGNAL BRACKET
Using a torx® socket wrench, install the turn signal bracket with
2 new torx® screws.
Torque: 7.5 N´m (75 kgf´cm, 65 in.´lbf)
HINT:
Make sure that the protrusion on the steering column housing
is fitted into the hole of the turn signal bracket.
8. INSTALL RELEASE LEVER SPRING
9. INSTALL SHIFT LEVER HOUSING
Using a torx® socket wrench, install the shift lever housing with
3 new torx® screws.
Torque: 12 N´m (120 kgf´cm, 9 ft´lbf)
10. INSTALL PARK LOCK CABLE ASSEMBLY (See page
AT±21)
11. INSTALL SHIFT LEVER
Using a torx® socket wrench, install the shift lever with a new
torx® screw.
Torque: 18 N´m (180 kgf´cm, 13 ft´lbf)
12. INSTALL COLUMN UPPER BRACKET
(a) Install the column upper bracket with 2 new tapered±
head bolts.
HINT:
Insert the bracket pin into the column tube hole.
(b) Tighten the tapered±head bolts until the bolt heads break
off.
13. INSTALL KEY CYLINDER LAMP ASSEMBLY
14. INSTALL TRANSPONDER KEY COIL