TOYOTA TERCEL 1996 Service Repair Manual

- ENGINE MECHANICALCYLINDER BLOCK
EM-69
490 Author
: Date
:
1996 TERCEL (RM440U)

EM0JQ-06
EM9411
EM9412
P20480
SST
P20478
SST
P20477
12 mm
Hexagon
Wrench EM-70
- ENGINE MECHANICALCYLINDER BLOCK
1996 TERCEL (RM440U)
DISASSEMBLY
1. M/T:
REMOVE CLUTCH COVER AND DISC
2. REMOVE FLYWHEEL (M/T) OR DRIVE PLATE (A/T)
3. REMOVE REAR END PLATE
4. INSTALL ENGINE TO ENGINE STAND FOR DIS-
ASSEMBLY
5. REMOVE TIMING BELT AND PULLEYS
6. REMOVE CYLINDER HEAD
7. REMOVE OIL DIPSTICK GUIDE AND GENERATOR
ADJUSTING BAR
8. REMOVE WATER PUMP WITH WATER INLET PIPE
9. REMOVE GENERATOR BRACKET
10. REMOVE KNOCK SENSOR
Using SST, remove the knock sensor.
SST 09816-30010
11. REMOVE RH ENGINE MOUNTING BRACKET
12. REMOVE OIL FILTER
13. REMOVE OIL PRESSURE SWITCH
Using SST, remove the oil pressure switch.
SST 09816-30010
14. REMOVE OIL PUMP AND PRESSURE REGULATOR
VA LV E
15. REMOVE OIL FILTER UNION
Using a 12 mm hexagon wrench, remove the oil filter union.

EM9988
EM3441
P20487
EM9392
EM3444
- ENGINE MECHANICALCYLINDER BLOCK
EM-71
1996 TERCEL (RM440U)
16. REMOVE REAR OIL SEAL RETAINER
(a) Remove the 4 bolts.
(b) Using a screwdriver, remove the oil seal retainer by prying
the portions between the oil seal retainer and main bear-
ing cap.
17. CHECK CONNECTING ROD THRUST CLEARANCE
Using a dial indicator, measure the thrust clearance while mov-
ing the rod back and forth.
Standard thrust clearance:
0.15 - 0.35 mm (0.0059 - 0.0138 in.)
Maximum thrust clearance:
0.45 mm (0.0177 in.)
If the thrust clearance is greater than maximum, replace the
connecting rod assembly. If necessary, replace the crankshaft.
18. REMOVE CONNECTING ROD CAPS AND CHECK OIL
CLEARANCE
(a) Check the matchmarks on the connecting rod and cap to
ensure correct reassembly.
(b) Remove the 2 connecting rod cap nuts.
(c) Using a soft-faced hammer, lightly tap the connecting rod
bolt and lift the cap and lower bearing.
HINT:
Keep the lower bearing inserted with the connecting rod cap.

EM3445
EM9405
EM3447
Plastigage
EM3448
EM3449
EM-72
- ENGINE MECHANICALCYLINDER BLOCK
1996 TERCEL (RM440U)
(d) Cover the connecting rod bolts with a short piece of hose
to protect the crankshaft from damage.
(e) Clean the crank pin and bearing.
(f) Check the crank pin bearing is for pitting and scratches.
If the crank pin or bearing is damaged, replace the bearings. If
necessary, grind or replace the crankshaft.
(g) Lay a strip of Plastigage across the crank pin.
(h) Install the connecting rod cap (See page EM-85).
Torque: 40 N´m (400 kgf´cm, 29 ft´lbf)
NOTICE:
Do not turn the crankshaft.
(i) Remove the connecting rod cap
(See procedure (b) and (c) above).
(j) Measure the Plastigage at its widest point.
Standard oil clearance:
STD0.016 - 0.048 mm (0.0006 - 0.0019 in.)
U/S 0.250.015 - 0.058 mm (0.0006 - 0.0023 in.)
Maximum oil clearance:
0.08 mm (0.0031 in.)
If the oil clearance is greater than maximum, replace the bear-
ings. If necessary, grind or replace the crankshaft.

P20473
Mark
1,2 or 3
Mark
1,2 or 3
P20491
EM3445
- ENGINE MECHANICALCYLINDER BLOCK
EM-73
1996 TERCEL (RM440U)
HINT:
If using a standard bearing, replace with one having the same
number as marked on the bearing cap. There are 3 sizes of
standard bearings, marked
º1º, º2º and º3º accordingly.
Reference:
Connecting rod big end inside diameter
Standard sized
U/S 0.25
Mark 1
Mark 2
Mark 3
-46.000 - 46.007 mm (1.8110 - 1.8113 in.)
46.007 - 46.014 mm (1.8113 - 1.8116 in.)
46.014 - 46.021 mm (1.8116 - 1.8118 in.)
46.000 - 46.021 mm (1.8110 - 1.8118 in.)
Crankshaft crank pin diameter
Standard sized
U/S 0.25
-
-42.985 - 43.000 mm (1.6923 - 1.6929 in.)
42.745 - 42.755 mm (1.6829 - 1.6833 in.)
Bearing center wall thickness
Standard sized
U/S 0.25
Mark 1
Mark 2
Mark 3
-1.487 - 1.491 mm (0.0585 - 0.0587 in.)
1.491 - 1.495 mm (0.0587 - 0.0589 in.)
1.495 - 1.499 mm (0.0589 - 0.0590 in.)
1.609 - 1.615 mm (0.0633 - 0.0636 in.)
(k) Completely remove the Plastigage.
19. REMOVE PISTON AND CONNECTING ROD AS-
SEMBLIES
(a) Using a ridge reamer, remove all the carbon from the top
of the cylinder.
(b) Cover the rod bolts with a short piece of hose to protect
the crankshaft from damage.
(c) Push out the piston and connecting rod assembly and the
upper bearing though the top of the cylinder block.
HINT:

Keep the bearing, connecting rod and cap together.

Arrange the piston and connecting rod assemblies in cor-
rect order.

P20547
P20190
481062
1
5
9
7
3
P20486
EM9403
EM-74
- ENGINE MECHANICALCYLINDER BLOCK
1996 TERCEL (RM440U)
20. CHECK CRANKSHAFT THRUST CLEARANCE
Using a dial indicator, measure the thrust clearance while prying
the crankshaft back and forth with a screwdriver.
Standard thrust clearance:
0.02 - 0.20 mm (0.0008 - 0.0079 in.)
Maximum thrust clearance:
0.3 mm (0.012 in.)
If the thrust clearance is greater than maximum, replace the
thrust washers as a set.
Thrust washer thickness:
STD2.430 - 2.480 mm (0.0957 - 0.0976 in.)
O/S 0.1252.493 - 2.543 mm (0.0981 - 0.1001 in.)
21. REMOVE MAIN BEARING CAPS AND CHECK OIL
CLEARANCE
(a) Uniformly loosen and remove the 10 main bearing cap
bolts, in several passes, in the sequence shown.
(b) Using the removed main bearing cap bolts, pry the main
bearing cap back and forth, and remove the 5 main bear-
ing caps, 5 lower bearings and 2 lower thrust washers
(No.3 main bearing cap only).
HINT:

Keep the lower bearing inserted together with cap.

Arrange the main bearing caps and lower thrust washers
in correct order.
(c) Lift out the crankshaft.
HINT:
Keep the upper bearings and upper thrust washers together
with the cylinder block.

P20488
EM9443
Plastigage
Z14291
4
810
6
2 159
73
EM9442
- ENGINE MECHANICALCYLINDER BLOCK
EM-75
1996 TERCEL (RM440U)
(d) Clean each main journal and bearing.
(e) Check each main journal and bearing for pitting and
scratches.
If the journal or bearing is damaged, replace the bearing.
If necessary, grind or replace the crankshaft.
(f) Place the crankshaft on the cylinder block.
(g) Lay a strip of Plastigage across each journal.
(h) Install the main bearing caps (See page EM-85).
Torque: 58 N´m (580 kgf´cm, 42 ft´lbf)
NOTICE:
Do not turn the crankshaft.
(i) Remove the main bearing caps.
(See procedure (a) and (b) above)
(j) Measure the Plastigage at its widest point.
Standard oil clearance:
STD0.016 - 0.035 mm (0.0006 - 0.0014 in.)
U/S 0.250.015 - 0.055 mm (0.0006 - 0.0022 in.)
Maximum oil clearance: 0.08 mm (0.0031 in.)
HINT:

If replacing the cylinder block subassembly, the bearing
standard clearance will be: 0.018- 0.045 mm
(0.0007-0.0018 in.).
If the oil clearance is greater than maximum replace the bear-
ings. If necessary, grind or replace the crankshaft.

N00287
Front
FrontMark
1, 2, 3,4 or 5
No.1 - No.5 Cylinder Block
Main Jounal Mark1, 2 or 3
No.1 - No.5 Crankshaft Journal
Mark 0, 1, 2
EXAMPLE: Cylinder block º2º + Crankshaft º1º
= Total number 3 (Use bearing º3º)
Number marked
Cylinder block
Crankshaft
Use bearing123
1
111 2
22
22
333445 000
EM9403
EM-76
- ENGINE MECHANICALCYLINDER BLOCK
1996 TERCEL (RM440U)

If using a standard bearing, replace it with one having the
same number. If the number of the bearing cannot be de-
termined, select the correct bearing by adding together
the numbers imprinted on the cylinder block and crank-
shaft, then selecting the bearing with the same number as
the total. There are 5 sizes of standard bearings, marked
º1º, º2º, º3º, º4º and º5º accordingly.
Reference:
Cylinder block main journal bore diameter
Standard sized
U/S 0.25
Mark 1
Mark 2
Mark 3
-54.018 - 54.024 mm (2.1267 - 2.1269 in.)
54.025 - 54.030 mm (2.1270 - 2.1272 in.)
54.031 - 54.036 mm (2.1272 - 2.1274 in.)
54.018 - 54.036 mm (2.1267 - 2.1274 in.)
Crankshaft journal diameter
Standard sized
U/S 0.25
Mark 0
Mark 1
Mark 2
-49.996 - 50.000 mm (1.9683 - 1.9685 in.)
49.991 - 49.995 mm (1.9681 - 1.9683 in.)
49.985 - 49.990 mm (1.9679 - 1.9681 in.)
49.745 - 49.755 mm (1.9585 - 1.9589 in.)
Bearing center wall thickness
Standard sized
U/S 0.25
Mark 1
Mark 2
Mark 3
Mark 4
Mark 5
-1.997 - 2.000 mm (0.0786 - 0.0787 in.)
2.001 - 2.003 mm (0.0788 - 0.0789 in.)
2.004 - 2.006 mm (0.0789 - 0.0790 in.)
2.007 - 2.009 mm (0.0790 - 0.0791 in.)
2.010 - 2.012 mm (0.0791 - 0.0792 in.)
2.118 - 2.124 mm (0.0834 - 0.0836 in.)
(k) Completely remove the Plastigage.
22. REMOVE CRANKSHAFT
(a) Lift out the crankshaft.
(b) Remove the upper main bearings and upper thrust wash-
ers from the cylinder block.
HINT:
Arrange the main bearings and thrust washers in correct order.

P20489
P20548
Z07984
SST SST
SST
SSTSSTPiston
Pin
SST
- ENGINE MECHANICALCYLINDER BLOCK
EM-77
1996 TERCEL (RM440U)
23. CHECK FIT BETWEEN PISTON AND PIN
Try to move the piston back and forth on the piston pin.
If any movement is felt, replace the piston and pin as a set.
24. REMOVE PISTON RINGS
(a) Using a piston ring expander, remove the compression
rings.
(b) Remove the 2 side rails and oil ring expander by hand.
HINT:
Arrange the rings in the correct order only.
25. DISCONNECT CONNECTING ROD FROM PISTON
(a) Using SST, press out the piston pin from the piston.
(b) Remove the connecting rod.
SST 09221-25024 (09221-00020, 09221-00030,
09221-00130, 09221-00140, 09221-00150)
HINT:

The piston and pin are a matched set.

Arrange the pistons, pins, rings, connecting rods and
bearings in correct order.

P00393
EM0JR-04
Z07983
P00390
EM9429
Front
Cylinder Bore Size Mark (1,2 or 3) EM-78
- ENGINE MECHANICALCYLINDER BLOCK
1996 TERCEL (RM440U)
INSPECTION
1. CLEAN CYLINDER BLOCK
(a) Remove the gasket material.
(b) Using a gasket scraper, remove all the gasket material
from the top surface of the cylinder block.
(c) Clean the cylinder block.
(d) Using a soft brush and solvent, thoroughly clean the cylin-
der block.
2. INSPECT TOP SURFACE OF CYLINDER BLOCK FOR
FLATNESS
Using a precision straight edge and feeler gauge, measure the
surfaces contacting the cylinder head gasket for warpage.
Maximum warpage: 0.05 mm (0.0020 in.)
If warpage is greater than maximum, replace the cylinder block.
3. INSPECT CYLINDER FOR VERTICAL SCRATCHES
Visually check the cylinder for vertical scratches.
If deep scratches are present, replace the cylinder block.
4. INSPECT CYLINDER BORE DIAMETER
HINT:
There are 3 sizes of the standard cylinder bore diameter,
marked º1º, º2º and º3º accordingly. The mark is stamped on the
top of the cylinder block.