Block TOYOTA TERCEL 1996 Service Repair Manual

IN07B-01
N13014
B A
P01214
- INTRODUCTIONIDENTIFICATION INFORMATION
IN-3
3 Author
: Date
:
1996 TERCEL (RM440U)
IDENTIFICATION INFORMATION
VEHICLE IDENTIFICATION AND
ENGINE SERIAL NUMBER
1. VEHICLE IDENTIFICATION NUMBER
The vehicle identification number is stamped on the vehicle
identification number plate and the certification label, as shown
in the illustration.
A: Vehicle Identification Number Plate
B: Certification Label
2. ENGINE SERIAL NUMBER
The engine serial number is stamped on the engine block, as
shown in the illustration.

V08423 Knock Sensor 1
GRECM
KNK
E1 12
E6
WIRING DIAGRAM
Wiring Diagram
This shows a wiring diagram of the circuit.
Use this diagram together with ELECTRICAL
WIRING DIAGRAM to thoroughly understand the
circuit.
Wire colors are indicated by an alphabetical code.
B = Black, L = Blue, R = Red, BR = Brown,
LG = Light Green, V = Violet, G = Green,
O = Orange, W = White, GR = Gray, P = Pink,
Y = Yellow, SB = Sky Blue
The first letter indicates the basic wire color and
the second letter indicates the color of the stripe.
DTC P0325Knock Sensor 1 Circuit Malfunction
CIRCUIT DESCRIPTION
Knock sensor is fitted to the cylinder block to detect engine knocking. This sensor contains a piezoelectric element which
generates a voltage when it becomes deformed, which occurs when the cylinder block vibrates due to knocking. If engine
knocking occurs, ignition timing is retarded to suppress it.
DTC No. DTC Detection Condition Trouble Area
P0325No knock sensor 1 signal to ECM with engine speed,
1,200 rpm or more.
Open or short in knock sensor1 circuit

Knock sensor 1 (looseness)

ECM
If the ECM detects the above diagnosis conditions, it operates the fall safe function in which the corrective retard angle
value is set to the maximum value.

Diagnostic Trouble Code No. and Detection Item

Circuit Description
The major role and operation, etc. of the circuit
and its component parts are explained.

Indicates the diagnostic trouble code, diagnostic
trouble code set parameter and suspect area of
the problem.

IN-24
- INTRODUCTIONHOW TO TROUBLESHOOT ECU CONTROLLED
SYSTEMS
1996 TERCEL (RM440U)
6. CIRCUIT INSPECTION
How to read and use each page is shown below.

- INTRODUCTIONTERMS
IN-33
33 Author
: Date
:
1996 TERCEL (RM440U) H/B
Hatchback
H-FUSEHigh Current Fuse
HIHigh
HIDHigh Intensity Discharge (Head Lamp)
HPUHydraulic Power Unit
HSGHousing
HTHard Top
HWSHeated Windshield System
IACIdle Air Control
ICIntegrated circuit
IDIIndirect Diesel Injection
IFSIndependent Front Suspension
IGIgnition
IIAIntegrated Ignition Assembly
INIntake (Manifold, Valve)
INTIntermittent
I/PInstrument Panel
IRSIndependent Rear Suspension
J/BJunction Block
J/CJunction Connector
KDKick-Down
LANLocal Area Network
LBLiftback
LCDLiquid Crystal Display
LEDLight Emitting Diode
LHLeft-Hand
LHDLeft-Hand Drive
L/H/WLength, Height, Width
LLCLong-Life Coolant
LNGLiquified Natural Gas
LOLow
LPGLiquified Petroleum Gas
LSDLimited Slip Differential
LSP & PVLoad Sensing Proportioning And Bypass Valve
LSPVLoad Sensing Proportioning Valve
MAX.Maximum
M-FUSEMedium Current Fuse
MICMicrophone
MILMalfunction Indicator Lamp
MIN.Minimum
MPMultipurpose
MPXMultiplex Communication System
M/TManual Transmission (Transaxle)
MTMount
MTGMounting
NNeutral

IN-34
- INTRODUCTIONTERMS
34 Author
: Date
:
1996 TERCEL (RM440U) NA
Natural Aspiration
No.Number
O/DOverdrive
OEMOriginal Equipment Manufacturing
OHCOverhead Camshaft
OHVOverhead Valve
OPTOption
O/SOversize
P & BVProportioning And Bypass Valve
PCSPower Control System
PCVPositive Crankcase Ventilation
PKBParking Brake
PPSProgressive Power Steering
PSPower Steering
PTOPower Take-Of f
R & PRack And Pinion
R/BRelay Block
RBSRecirculating Ball Type Steering
R/FReinforcement
RFSRigid Front Suspension
RHRight-Hand
RHDRight-Hand Drive
RLYRelay
ROMRead Only Memory
RrRear
RRRear-Engine Rear-Wheel Drive
RRSRigid Rear Suspension
RWDRear-Wheel Drive
SDNSedan
SENSensor
SICSStarting Injection Control System
SMTSequential Manual Transmission
SOCState Of Charge
SOHCSingle Overhead Camshaft
SPECSpecification
SPISingle Point Injection
SRSSupplemental Restraint System
SSMSpecial Service Materials
SSTSpecial Service Tools
STDStandard
STJCold-Start Fuel Injection
SWSwitch
SYSSystem
T/ATransaxle
TACHTachometer
TBIThrottle Body Electronic Fuel Injection

MA003-28
MA-4
- MAINTENANCEUNDER HOOD
42 Author
: Date
:
1996 TERCEL (RM440U)
UNDER HOOD
GENERAL MAINTENANCE
1. GENERAL NOTES

Maintenance items may vary from country to country. Check the owner's manual supplement in which
the maintenance schedule is shown.

Every service item in the periodic maintenance schedule must be performed.

Periodic maintenance service must be performed according to whichever interval in the periodic main-
tenance schedule occurs first, the odometer reading (miles) or the time interval (months).

Maintenance service after the last period should be performed at the same interval as before unless
otherwise noted.

Failure to do even one item can cause the engine to run poorly and increase exhaust emissions.
2. WINDSHIELD WASHER FLUID
Check that there is sufficient fluid in the tank.
3. ENGINE COOLANT LEVEL
Check that the coolant level is between the FULL and LOW lines on the see-through reservoir.
4. RADIATOR AND HOSES
(a) Check that the front of the radiator is clean and not blocked with leaves, dirt or bugs.
(b) Check the hoses for cracks, kinks, rot or loose connections.
5. BATTERY ELECTROLYTE LEVEL
Check that the electrolyte level of all battery cells is between the upper and lower level lines on the case.
If level is low, add distilled water only.
6. BRAKE AND CLUTCH FLUID LEVELS
(a) Check that the brake fluid level is near the upper level line on the see-through reservoir.
(b) Check that the clutch fluid level is within ±5 mm (0.20 in.). of the reservoir hem.
7. ENGINE DRIVE BELTS
Check drive belt for fraying, cracks, wear or oiliness.
8. ENGINE OIL LEVEL
Check the level on the dipstick with the engine turned off.
9. POWER STEERING FLUID LEVEL
(a) Check the level.
(b) The level should be in the HOT or COLD range depending on the fluid temperature.
10. AUTOMATIC TRANSMISSION FLUID LEVEL
(a) Park the vehicle on a level surface.
(b) With the engine idling and the parking brake applied, shift the selector into all positions from the P to
L, and then shift into the P position.
(c) Turn and pull out the dipstick and wipe off the fluid with a clean rag. Reinsert the dipstick and check
that the fluid level is in the HOT range.
(d) Do this check with the fluid at normal driving temperature (70 - 80°C, 158 - 176°F).
If the If the level is at the low side, add fluid.
NOTICE:
Do not overfill.
HINT:
Wait until the engine cools down (approx. 30 min.) before checking the fluid level after extended driving at
high speeds, in hot weather, in heavy traffic or pulling a trailer.
11. EXHAUST SYSTEM
Visually inspect for cracks, holes or loose supports.
If any change in the sound of the exhaust or smell of the exhaust fumes is noticed, have the cause located
and corrected.

MA03P-02
P19780BootBoot
P19895
- MAINTENANCECHASSIS
MA-7
45 Author
: Date
:
1996 TERCEL (RM440U)
CHASSIS
INSPECTION
1. INSPECT STEERING LINKAGE
(a) Check the steering wheel freeplay (See page SR-10).
(b) Check the steering linkage for looseness or damage.

Check that the tie rod ends do not have excessive
play.

Check that the dust seals and boots are not dam-
aged.

Check that the boot clamps are not loose.
2. INSPECT SRS AIRBAG (See page RS-2)
3. INSPECT STEERING GEAR HOUSING OIL
Check the steering gear housing for oil leakage.
4. INSPECT DRIVE SHAFT BOOTS
Check the drive shaft boots for clamp looseness, leakage or
damage.
5. INSPECT BALL JOINT AND DUST COVERS
(a) Inspect the ball joints for excessive looseness.
(1) Jack up the front of the vehicle and place wooden
blocks with a height of 180 - 200 mm (7.09 - 7.87
in.) under the front tires.
(2) Lower the jack until there is about half a load on the
front coil spring. Place stands under the vehicle for
safety.
(3) Make sure the front wheels are in a straightforward
position and block the wheel with chocks.
(4) Move the lower arm up and down, and check that
the ball joint has no excessive play.
Maximum ball joint vertical play: 0 mm (0 in.)
If there is play, replace the ball joint.

PP19C-01
PP-28
- PREPARATIONSTARTING
1996 TERCEL (RM440U)
EQUIPMENT
Caliper gaugeCenter bearing for planetary type
Dial indicatorCommutator
Magnetic finger
MicrometerPlanet carrier shaft for planetary type
PressReduction type
Pull scaleBrush spring
SandpaperCommutator
Torque wrench
V-block
Vernier calipersCommutator, Brush

SS0N5-03
- SERVICE SPECIFICATIONSENGINE MECHANICAL
SS-5
135 Author
: Date
:
1996 TERCEL (RM440U)
ENGINE MECHANICAL
SERVICE DATA
Compression
pressureat 250 rpm STD
Minimum
Difference of pressure between each cylinder1,275 kPa (13.0 kgf/cm2, 185 psi) or more
981 kPa (10.0 kgf/cm2, 142 psi)
98 kPa (1.0 kgf/cm2, 14 psi) or less
Valve clearanceat cold Intake
Exhaust
Adjusting shim (for repair part) No. 02
04
06
08
10
12
14
16
18
20
22
24
26
28
30
32
340.15 - 0.25 mm (0.006 - 0.010 in.)
0.31 - 0.41 mm (0.012 - 0.016 in.)
2.500 mm (0.0984 in.)
2.550 mm (0.1004 in.)
2.600 mm (0.1024 in.)
2.650 mm (0.1043 in.)
2.700 mm (0.1063 in.)
2.750 mm (0.1083 in.)
2.800 mm (0.1102 in.)
2.850 mm (0.1122 in.)
2.900 mm (0.1142 in.)
2.950 mm (0.1161 in.)
3.000 mm (0.1181 in.)
3.050 mm (0.1201 in.)
3.100 mm (0.1220 in.)
3.150 mm (0.1240 in.)
3.200 mm (0.1260 in.)
3.250 mm (0.1280 in.)
3.300 mm (0.1299 in.)
Ignition timingw/ Terminals TE1 and E1 connected of DLC110° BTDC @ idle
Idle speed-750 ± 50 rpm
Idler pulley tension
springFree length
Installed load at 47.4 mm (1.866 in.)38.4 mm (1.512 in.)
32 N (3.3 kgf, 7.3 lbf)
Cylinder headWarpage
Cylinder block side Maximum
Manifold sideMaximum
Valve guide bore diameter STD
O/S 0.05
Valve seat
Refacing angleIntake
Exhaust
Contacting angle
Contacting width
0.05 mm (0.0020 in.)
0.05 mm (0.0020 in.)
11.000 - 11.027 mm (0.4331 - 0.4342 in.)
11.050 - 11.077 mm (0.4350 - 0.4361 in.)
30°, 45°, 60°, 75°
30°, 45°, 75°
45°
1.0 - 1.4 mm (0.039 - 0.055 in.)
Valve guide
bushingInside diameter
Outside diameter (for repair part) STD
O/S 0.056.010 - 6.030 mm (0.2366 - 0.2374 in.)
11.048 - 11.059 mm (0.4350 - 0.4354 in.)
11.098 - 11.109 mm (0.4369 - 0.4374 in.)
ValveValve overall length STD Intake
Exhaust
Minimum Intake
Exhaust
Valve face angle
Stem diameterIntake
Exhaust
Stem oil clearance STD Intake
Exhaust
Maximum Intake
Exhaust
Margin thickness STD
Minimum93.45 mm (3.6791 in.)
93.89 mm (3.6965 in.)
92.95 mm (3.6594 in.)
93.39 mm (3.6768 in.)
44.5°
5.970 - 5.985 mm (0.2350 - 0.2356 in.)
5.965 - 5.980 mm (0.2348 - 0.2354 in.)
0.025 - 0.060 mm (0.0010 - 0.0024 in.)
0.030 - 0.065 mm (0.0012 - 0.0026 in.)
0.08 mm (0.0031 in.)
0.10 mm (0.0039 in.)
0.8 - 1.2 mm (0.031 - 0.047 in.)
0.5 mm (0.020 in.)

SS-6
- SERVICE SPECIFICATIONSENGINE MECHANICAL
136 Author
: Date
:
1996 TERCEL (RM440U) Valve spring
Deviation Maximum
Free length
Installed tension at 31.8 mm (1.252 in.)2.0 mm (0.079 in.)
53.58 mm (2.1094 in.)
148 - 164 N (15.1 - 16.7 kgf, 33.3 - 36.8 lbf)
CamshaftThrust clearance STD
Maximum
Cam lobe height STD Intake
Exhaust
Maximum Intake
Exhaust
Journal diameter Exhaust No. 1
Others
Journal oil clearance STD
Maximum
Circle runout
Camshaft gear backlash STD
Maximum
Camshaft gear spring end free distance0.045 - 0.100 mm (0.0018 - 0.0039 in.)
0.12 mm (0.0047 in.)
41.514 - 41.614 mm (1.6344 - 1.6383 in.)
41.011 - 41.111 mm (1.6146 - 1.6185 in.)
41.35 mm (1.6279 in.)
40.85 mm (1.6083 in.)
24.949 - 24.965 mm (0.9822 - 0.9829 in.)
22.949 - 22.965 mm (0.9035 - 0.9041 in.)
0.035 - 0.072 mm (0.0014 - 0.0028 in.)
0.10 mm (0.0039 in.)
0.04 mm (0.0016 in.)
0.020 - 0.200 mm (0.0008 - 0.0079 in.)
0.30 mm (0.0118 in.)
22.5 - 22.9 mm (0.886 - 0.902 in.)
Valve lifterLifter diameter
Lifter bore diameter
Oil clearance STD
Maximum27.975 - 27.985 mm (1.1014 - 1.1018 in.)
28.000 - 28.021 mm (1.1024 - 1.1032 in.)
0.015 - 0.046 mm (0.0006 - 0.0018 in.)
0.10 mm (0.0039 in.)
ManifoldWarpageMaximum Intake
Exhaust0.1 mm (0.004 in.)
0.5 mm (0.020 in.)
Spark tubeProtrusion47.5 - 48.5 mm (1.870 - 1.909 in.)
Cylinder blockCylinder head surface warpage Maximum
Cylinder bore diameter Mark 1
2
3
Maximum
Main journal bore diameter (Reference) Mark 1
2
30.05 mm (0.0020 in.)
74.000 - 74.010 mm (2.9134 - 2.9138 in.)
74.011 - 74.020 mm (2.9138 - 2.9142 in.)
74.021 - 74.030 mm (2.9142 - 2.9146 in.)
74.23 mm (2.9244 in.)
54.018 - 54.024 mm (2.1267 - 2.1269 in.)
54.025 - 54.030 mm (2.1270 - 2.1272 in.)
54.031 - 54.036 mm (2.1272 - 2.1274 in.)
Piston and piston
ringPiston diameter Mark 1
2
3
Piston oil clearance STD
Maximum
Piston ring groove clearance No. 1
No. 2
Piston ring end gap STD No. 1
No. 2
Oil
Maximum No. 1
No. 2
Oil73.900 - 73.910 mm (2.9094 - 2.9098 in.)
73.910 - 73.920 mm (2.9098 - 2.9102 in.)
73.920 - 73.930 mm (2.9102 - 2.9106 in.)
0.09 - 0.11 mm (0.0035 - 0.0043 in.)
0.13 mm (0.0051 in.)
0.04 - 0.08 mm (0.0016 - 0.0031 in.)
0.03 - 0.07 mm (0.0012 - 0.0028 in.)
0.26 - 0.48 mm (0.0102 - 0.0189 in.)
0.30 - 0.57 mm (0.0118 - 0.0224 in.)
0.13 - 0.50 mm (0.0059 - 0.0197 in.)
1.07 mm (0.0421 in.)
1.02 mm (0.0354 in.)
1.10 mm (0.0433 in.)

SS0N6-04
SS-8
- SERVICE SPECIFICATIONSENGINE MECHANICAL
1996 TERCEL (RM440U)
TORQUE SPECIFICATION
Part tightenedN´mkgf´cmft´lbf
Cylinder head cover x Cylinder head7.07061 in.´lbf
No. 2 idler pulley x Cylinder head2828020
Camshaft timing pulley x Camshaft5151037
No. 1 idler pulley x Cylinder block18.518513
Crankshaft pulley x Crankshaft1551,55011 2
No. 2 crankshaft pulley x Crankshaft pulley1919514
RH engine mounting insulator x RH engine mounting bracket6465047
RH engine mounting insulator x Body7374054
No. 1 engine hanger x Cylinder head2121015
No. 2 engine hanger x Cylinder head5353038
Cylinder head x Cylinder block 1st
2nd45
Turn 90°450
Turn 90°33
Turn 90°
Camshaft bearing cap x Cylinder head131309
Intake manifold x Cylinder head19.519514
Intake manifold stay x Intake manifold2020015
Intake manifold stay x Cylinder block2020015
Exhaust manifold x Cylinder head4848035
Exhaust manifold stay x Cylinder block4040029
Exhaust manifold stay x Exhaust manifold4040029
Exhaust manifold heat insulator x Exhaust manifold8.08069 in.´lbf
Water outlet housing x Cylinder head3030022
Camshaft position sensor x Cylinder head8.08069 in.´lbf
EGR VSV x Cylinder head17.517513
EGR valve x Cylinder head17.517513
EGR pipe x EGR valve4040029
EGR pipe x Intake manifold3030022
PS ump bracket x Cylinder head4344032
Fuel inlet hose x Fuel filter2930022
Front exhaust pipe x Exhaust manifold6263049
Connecting rod cap x Connecting rod4040029
Crankshaft bearing cap x Cylinder block5858042
Rear oil seal retainer x Cylinder block7.57565 in.´lbf
Oil filter union x Cylinder block2525018
Oil pressure switch x Cylinder block131309
RH engine mounting bracket x Cylinder block5959043
Knock sensor x Cylinder block4545033
Generator bracket x Cylinder block2424018
Rear end plate x Cylinder block101007
Flywheel x Crankshaft9090065
Drive plate x Crankshaft9090065
Drive plate x Torque converter clutch2525018
A/C compressor bracket x Cylinder block2728020
PS pump adjusting strut x Cylinder block2121015