headlights VOLVO S60 2009 Owner´s Manual

08 Car careWashing and cleaning the vehicle
08176
Washing the vehicle•
The vehicle should be washed at regular
intervals since dirt, dust, insects and tar
spots adhere to the paint and may cause
damage. It is particularly important to wash
the vehicle frequently in the wintertime to
prevent corrosion, when salt has been
used on the roads.
•
When washing the vehicle, do not expose
it to direct sunlight. Use lukewarm water to
soften the dirt before you wash with a
sponge, and plenty of water, to avoid
scratching.
•
Bird droppings: Remove from paintwork as
soon as possible. Otherwise the finish may
be permanently damaged.
•
A detergent can be used to facilitate the
softening of dirt and oil.
•
A water-soluble grease solvent may be
used in cases of sticky dirt. However, use
a wash place equipped with a drainage
separator.
•
Dry the vehicle with a clean chamois and
remember to clean the drain holes in the
doors and rocker panels.
•
Tar spots can be removed with kerosene
or tar remover after the vehicle has been
washed.
•
A stiff-bristle brush and lukewarm soapy
water can be used to clean the wiper
blades. Frequent cleaning of the wind-shield and wiper blades improves visibility
considerably and also helps prolong the
service life of the wiper blades.
•
Wash off the dirt from the underside (wheel
housings, fenders, etc.).
•
In areas of high industrial fallout, more fre-
quent washing is recommended.CAUTION
•
When washing or steam cleaning the
engine, avoid spraying water or steam
directly on the electrical components or
toward the rear side of the engine.
•
Dirt, snow, etc., on the headlights can
reduce lighting capacity considerably.
Clean the headlights regularly, for
example when refueling.
•
During high pressure washing, the
spray mouthpiece must never be closer
to the vehicle than 13 " (30 cm). Do not
spray into the locks.
Special moonroof cautions:
•
Always close the moonroof and sun
shade before washing your vehicle.
•
Never use abrasive cleaning agents on
the moonroof.
•
Never use wax on the rubber seals
around the moonroof.
•
After cleaning the engine, the spark plug
wells should be inspected for water and
blown dry if necessary.
Suitable detergents: Special vehicle washing
detergents should be used. A suitable mixture
is about 2.5 fl. oz. (8.5 cl) of detergent to 2.6 US
gal. (10 liters) of warm water. After washing
with a detergent the vehicle should be well
rinsed with clean water.
Exterior components
Volvo recommends the use of special cleaning
products, available at your Volvo retailer, for
cleaning colored plastic, rubber, or ornamental
components such as chromed strips on the
exterior of your vehicle. The instructions for
using these products should be followed care-
fully. Solvents or stain removers should not be
used.CAUTION
•
Avoid waxing or polishing plastic or rub-
ber components
•
Polishing chromed strips can wear
away or damage the surface
•
Polishes containing abrasive sub-
stances should not be used

08 Car care
Washing and cleaning the vehicle
08``177
NOTE
When washing the vehicle, remember to
remove dirt from the drain holes in the doors
and sills
WARNING
When the vehicle is driven immediately after
being washed, apply the brakes several
times in order to remove any moisture from
the brake linings.
Engine cleaning agents should not be used
when the engine is warm. This constitutes a
fire risk.Automatic washing - simple and quick•
We do NOT recommend washing your
vehicle in an automatic wash during the
first six months (because the paint will not
have hardened sufficiently).
•
An automatic wash is a simple and quick
way to clean your vehicle, but it is worth
remembering that it may not be as thor-
ough as when you yourself go over the
vehicle with sponge and water. Keeping
the underbody clean is most important,
especially in the winter. Some automatic
washers do not have facilities for washing
the underbody.
•
Before driving into an automatic vehicle
wash, make sure that side view mirrors,auxiliary lamps, etc, are secure, and that
any antenna(s) are retracted or removed.
Otherwise there is risk of the machine dis-
lodging them.
Exterior lightingCondensation may form temporarily on the
inside of the lenses of exterior lights such as
headlights, fog lights, or tail lights. This is nor-
mal and the lights are designed to withstand
moisture. Normally, condensation will dissi-
pate after the lights have been on for a short
time.Polishing and waxing•
Normally, polishing is not required during
the first year after delivery, however, wax-
ing may be beneficial.
•
Before applying polish or wax the vehicle
must be washed and dried. Tar spots can
be removed with kerosene or tar remover.
Difficult spots may require a fine rubbing
compound.
•
After polishing use liquid or paste wax.
•
Several commercially available products
contain both polish and wax.
•
Waxing alone does not substitute for pol-
ishing a dull surface.
•
A wide range of polymer-based vehicle
waxes can be purchased today. Thesewaxes are easy to use and produce a long-
lasting, high-gloss finish that protects the
bodywork against oxidation, road dirt and
fading.
•
Do not polish or wax your vehicle in direct
sunlight (the surface of the vehicle should
not be warmer than 113 ° F (45 ° C).CAUTION
Volvo does not recommend the use of long-
life or durable paint protection coatings,
some of which may claim to prevent pitting,
fading, oxidation, etc. These coatings have
not been tested by Volvo for compatibility
with your vehicle's clear coat. Some of them
may cause the clear coat to soften, crack,
or cloud. Damage caused by application of
paint protection coatings may not be cov-
ered under your vehicle's paint warranty.Cleaning the upholsteryFabricClean with soapy water or a detergent. For
more difficult spots caused by oil, ice cream,
shoe polish, grease, etc., use a clothing/fabric
stain remover. Consult your Volvo retailer.Interior plastic componentsCleaning interior plastic components should
be done with a cleaning agent specially

09 Maintenance and servicing
Maintaining your vehicle
09
185 Owner maintenance
Periodic maintenance requirements and inter-
vals are described in your vehicle's Warranty
and Service Records Information booklet.
The following points can be carried out
between the normally scheduled maintenance
services.Each time the vehicle is refueled:•
Check the engine oil level
•
Clean the windshield, windshield wipers,
headlights, and tail lights
Monthly:•
Check cold tire pressure in all tires. Inspect
the tires for wear.
•
Check that engine coolant and other fluid
levels are between the indicated "min" and
"max" markings.
•
Clean interior glass surfaces with a glass
cleaner and soft paper towels.
•
Wipe driver information displays with a soft
cloth.
•
Visually inspect battery terminals for cor-
rosion. Corrosion may indicate a loose ter-
minal connector, or a battery near the end
of its useful service life. Consult a trained
and qualified Volvo service technician for
additional information.
As needed:•
Wash the vehicle, including the undercar-
riage, to reduce wear that can be caused
by a buildup of dirt, and corrosion that can
be caused by salt residues.
•
Clean leaves and twigs from air intake
vents at the base of the windshield, and
from other places where they may collect.NOTE
Complete service information for qualified
technicians is available online for purchase
or subscription at www.volvotechinfo.com.

09 Maintenance and servicingReplacing bulbs
09198
When replacing bulbs, keep the following
points in mind:•
Never touch the glass of bulbs with your
fingers. Grease and oils from your fingers
vaporize in the heat and will leave a deposit
on the reflector, which will damage it.
•
The optional Active Bi-Xenon headlight
bulbs contain trace amounts of mercury.
These bulbs should always be disposed of
by an authorized Volvo retailer.
The following bulbs should only be replaced by
an authorized Volvo service technician:
•
Active Bi-Xenon headlights,
•
Courtesy (dome) lighting,
•
Reading lights,
•
Glove compartment lights
•
Turn signals and courtesy lights in the side
door mirrors
•
High-mounted brake lights
•
Diodes in the rear tail lightsNOTE
For information regarding any other bulbs
not mentioned in this section, please con-
tact your Volvo retailer or a trained and
authorized Volvo service technician.
Replacing bulbs at the front of the
vehicle
WARNING
•
The engine should not be running when
changing bulbs.
•
When changing in the headlight hous-
ing, if the engine has been running just
prior to replacing bulbs, please be
aware that components in the engine
compartment will be hot.
G027278
All front bulbs (except the optional front fog
lights) are replaced from the engine compart-
ment.
WARNING
Active Bi-Xenon headlights (option) - due to
the high voltage used by these headlights,
these bulbs should only be replaced by a
trained and qualified Volvo service techni-
cian.Location of the bulbs in the headlight
housing
G028433
Side marker lightTurn signal

09 Maintenance and servicing
Replacing bulbs
09``199
Low beam headlight/parking light (halogen
headlights)High beam headlight, parking light (Active
Bi-Xenon headlights)
Certain models may have a plastic tube that
may hinder access to the bulbs. This tube can
be broken off and discarded.NOTE
If you encounter difficulty when changing a
bulb, please contact a trained and qualified
Volvo service technician.Low beam headlight
G028435
Low beam bulb (halogen headlights)
Removing the defective bulb:1. Switch off the headlights and turn the igni-
tion switch to position 0.
2. Remove the plastic cover.
3. Disconnect the wiring connector.
Loosen the retaining spring by first moving
it to the right and then moving it outward
and downward, out of the way.
Pull out the defective bulb.
G028436
Installing the new bulb:
Insert the new bulb, without touching the
glass, with the guide lug upward. The bulb
will only seat properly in this position.
Move the retaining spring up and push it
slightly to the left until it seats properly.
1. Reconnect the wiring connector.
2. Reinstall the plastic cover.
NOTE
If the vertical aim of your headlights needs
to be adjusted for any reason (e.g., towing
a trailer for extended periods), this should
be done by a trained and qualified Volvo
service technician.High beam headlight
G028437
High beam bulb

09 Maintenance and servicingReplacing bulbs
09200
(Halogen headlights)Removing the defective bulb:1. Switch off the headlights and turn the igni-
tion switch to position 0.
2. Remove the cover to access the bulb
assembly.
3. Turn the bulb counterclockwise and pull it
out.
4. Disconnect the wiring connector by press-
ing the lock tab out and pulling.
5. Twist the bulb counterclockwise, and pull
it out of the holder.Installing the new bulb:1. Connect the wiring connector to the new
bulb until it clicks into place.
2. Insert the bulb into the headlight housing
and turn it until it is securely in place.
3. Press the cover back into place.
Parking light
G022733
(Halogen headlights)Removing the defective bulb:1. Switch off the headlights and turn the igni-
tion switch to position 0.
2. Remove the plastic cover of the low beam
headlight assembly. Pull out the parking
light holder.
3. Pull the bulb out of the holder.Installing the new bulb:1. Press a new bulb into the holder
2. Reinsert the bulb and holder into place.
3. Reinstall the plastic cover.
Parking light
G027171
(Active Bi-Xenon headlights)Removing the defective bulb:1. Switch off the headlights and turn the igni-
tion switch to position 0.
2. Remove the plastic cover of the high beam
headlight assembly. Pull out the parking
light holder.
3. Pull the bulb out of the holder.Installing the new bulb:1. Press a new bulb into the holder
2. Reinsert the bulb and holder into place.
3. Reinstall the plastic cover.

09 Maintenance and servicing
Replacing bulbs
09``201 Turn signal, driver's side
G028438
Removing the defective bulb:1. Switch off the headlights and turn the igni-
tion switch to position 0.
2. Pull out the bulb holder by twisting it coun-
terclockwise.
3. Remove the bulb from the holder by press-
ing it in and turning it counterclockwise.Installing the new bulb:1. Insert the new bulb into the holder by
pressing it in and turning it clockwise.
2. Reinsert the bulb holder in the headlight
housing and twist it clockwise until it seats
properly.
Turn signal, passenger's side
G027283
1. Switch off the headlights and turn the igni-
tion switch to position 0.
2. Remove radiator pipe (1) from the box.
3. Remove filler pipe screw (2).
4. Pull the filler pipe (3) straight up.
5. Remove vent hose (4) from filler pipe.Installing the new bulb:1. Replace the bulb (same procedure as the
driver's side bulb).
2. Ensure that the seal between the washer
fluid reservoir and the filler pipe is correctly
positioned.3. Press the filler pipe (3) back into position.
4. Press the vent hose (4) into place on the
filler pipe.
5. Reinstall and tighten the filler pipe screw
(2).
6. Reinstall the radiator pipe to the box (1).
Side marker light
G028439
Side marker light1. Turn the lamp holder counterclockwise
and pull it out.
2. Pull out the defective bulb and insert a new
one.

09 Maintenance and servicingReplacing bulbs
09202
3. Reinsert the lamp holder and turn it clock-
wise until it seats properly.Front fog lights (option)
G027227
Front fog lightRemoving the defective bulb:1. Switch off the headlights and turn the igni-
tion switch to position 0.
2. Turn the bulb holder slightly counterclock-
wise.
3. Pull out and remove the bulb.Installing the new bulb:1. Insert the new bulb (it can only be inserted
in one position).2. Reinsert the bulb holder and turn it clock-
wise. "TOP" must be upward.

09 Maintenance and servicing
Fuses
09``209 Fuse box in the passenger compartment, behind the plastic cover
G028412
This fuse box is located behind the plastic
cover below the steering wheel. When replac-
ing a blown fuse, be sure to replace it with a
new one of the same color and amperage (writ-
ten on the fuse).No.
A
1
Heated passenger's seat
(option)
15
2
Heated driver's seat (option)
15
3
Horn
15
4
–
–
No.
A
5
–
–
6
–
–
7
–
–
8
Alarm siren (option)
5
9
Break light switch feed
5
10
Instrument panel, climate sys-
tem, power driver's seat
(option)
10
No.
A
11
12-volt sockets - front and rear
seats
15
12
–
–
13
–
14
–
15
ABS, DSTC
5
16
Power steering, Active Bi-
Xenon headlights (option)
10

11 Specifications
Bulbs
11
243
Bulb
Output
Type
Low beam headlight
55W
H7
Active Bi-Xenon headlight (option)
35W
D2S
High beam headlight
55W
HB3
Brake light, back-up light, rear fog light
21W
BA15s
Turn signals front/rear (amber bulb)
21W
BAU15s
Rear parking lights/side marker lights
5W
BAY15d
Footwell lighting, trunk lighting, license plate lighting
5W
SV8.5
Vanity mirror
1.2W
SV5.5
Front parking lights/side marker lights
5W
W2.1X9.5d
Turn signal in door mirror (amber bulb)
5W
W2.1X9.5d
Front fog lights
55W
H11
Glove compartment lighting
3W
BA9
WARNING
Active Bi-Xenon headlights (option) – due to
the high voltage used by these headlights,
these bulbs should only be replaced by an
authorized Volvo service technician.