battery ASTON MARTIN V8 VANTAGE 2010 Owners Manual
[x] Cancel search | Manufacturer: ASTON MARTIN, Model Year: 2010, Model line: V8 VANTAGE, Model: ASTON MARTIN V8 VANTAGE 2010Pages: 947, PDF Size: 43.21 MB
Page 497 of 947
Brake Actuation System (06.06)
Brake System (06.00)
May 2007 Workshop Manual 6-6-11
11. Loosen and disconnect RH/LH brake tube union from in line connection (see Fig. 2).
12. Release brake tube from clips (x2), remove brake tube.
Installation
1. Install brake tube, connect unions, secure brake tube in clips (x2), torque tighten unions.
2. Install LH/RH front wheel arch liner (see Workshop Manual procedure 01.02.FB/01.02.GB Wheel Arch
Liner - Front - LH - Renew
3. Remove pedal support.
4. Top-up brake fluid.
5. Bleed brake Caliper with assistance.
6. Remove bleed bottle.
7. Install bleed nipple dust caps.
8. Clean off excess fluid.
9. Top-up brake fluid.
10. Install road wheel(s)).
11. Lower vehicle on ramp.
Dynamic Stability Control Module-
Renew
Removal
1. Raise vehicle on ramp.
2. Disconnect vehicle battery.
3. Remove road wheel(s).
4. Remove bleed nipple dust caps.
5. Position bleed container, connect bleed hose to LHR Caliper, open bleed nipples (x1).
6. Position bleed container, connect bleed hose to LHF Caliper, open bleed nipples (x1).
7. Depress brake pedal >60 mm and secure with support.
8. Tighten LHR bleed nipple, disconnect bleed hose, remove bleed container and fit dust cap.
9. Tighten LHF bleed nipple, disconnect bleed hose, remove bleed container and fit dust cap.
10. Remove LH front wheel arch liner (see Workshop Manual procedure 01.02.FB Wheel Arch Liner - Front -
LH - Renew).
11. Disconnect modulator multiplug.
12. Mark brake pipe unions fo r assembly purposes. Loosen
and disconnect brake pipe un ions (x6) from modulator.
Plug modulator and pipe connections.
13. Remove Torx bolts (x3) securing modulator mounting bracket to body. Remove modulator.
14. Remove Torx bolts (x3) securing modulator to mounting bracket. Collect mounting bracket from modulator.
Installation
1. Install modulator to mounting bracket, install and torque tighten Torx bolts (x3).
2. Install modulator to body, install and torque tighten Torx bolts (x3).
3. Remove plugs. Install and torque tighten brake unions (x6) to modulator.
4. Connect modulator multiplug.
Fig. 2
Repair Operation Time (ROT)
A0606128
WA R N I N G
AVOID SKIN / EYE CONTACT OR INGESTION OF
BRAKE FLUID. IF SKIN OR EYES ARE SPLASHED WITH BRAKE FLUID, RINSE THE AFFECTED AREA
IMMEDIATELY WITH PLENTY OF WATER AND OBTAIN
MEDICAL ATTENTION. IF BRAKE FLUID IS INGESTED, OBTAIN IMMEDIATE MEDICAL ATTENTION.
WA R N I N G
BRAKE FLUID IS HYGROSCOPI C. IF KEPT IN OPENED
CONTAINERS IT WILL ABSORB WATER VAPOUR. USE ONLY BRAKE FLUID FROM FRESHLY OPENED
CONTAINERS WHEN TOPPING-UP THE BRAKE FLUID RESERVOIR.
Caution
Brake fluid must not be allo wed to contact the vehicle
paint work. Remove spilt brake fluid from the paint work
by rinsing away with running water.
Caution
Always plug pipe ends to prevent ingress of dirt or moisture into the system.
Page 510 of 947
Anti-lock Braking System (ABS) (06.09)
Brake system (06.00)
6-9-4 Workshop ManualIssue 4, November 2008
Maintenance
ABS Modulator - Remove and Install
Remove
1. Disconnect the vehicle battery.
2. Raise the vehicle and make it safe.
3. Remove the four road wheels.
4. Remove the dust caps from the four brake caliper bleed
nipples .
5. Put a container in position under the rear left-side caliper to collect brake fluid.
6. Connect a bleed hose to rear left-side caliper.
7. Open the bleed nipple.
8. Put a container in position under the front left-side caliper to collect brake fluid.
9. Connect a bleed hose to front left-side caliper
10. Open the bleed nipple.
11. Operate the brake pedal more than 60 mm and install a pedal clamp to hold it.
12. Tighten the two bleed nipples.
13. Disconnect the two bleed hoses.
14. Remove the two fluid containers.
15. Install the two dust caps.
16. Remove the five or six screws that attach the rear half of the front left wheelarch liner.
17. Remove the self-tapping screw that attaches the rear of the wheelarch liner into the wheelarch.
18. Move the wheel arch liner to get access. 19. Disconnect the electrical connector from the modulator.
20. Put a label on each brake pipe union for the assembly
procedure.
21. Loosen and disconnect the six brake pipe unions from
the modulator. Install plugs into the modulator and the
pipe connections.
22. Remove the three M8 Torx-head screws (1) that attach the modulator mounting bracket to the body.
23. Remove the modulator.
24. Remove the three M6 Torx-head bolts that attach the modulator to the mounting bracket. Remove the
mounting bracket from the modulator.
Installation
1. Install the modulator onto the mounting bracket.
2. Install and torque the three M6 Torx-head bolts.
3. Install the modulator to the body.
4. Install and torque the three M8 Torx-head screws.
5. Remove the sealing plugs.
6. Install and torque the six brake unions to the modulator.
7. Connect the electrical connector to the modulator.
8. Put the wheel arch liner back in the correct position.
9. Install the self-tapping screw that attaches the rear of the wheelarch liner into the wheelarch.
10. Install the five or six scre ws to attach the wheel arch
liner.
11. Bleed the braking system (Refer to ’Brake Bleeding - AMDS
Page 518 of 947
Manual Transmission (07.03)
Transmission (07.00)7-3-2 Workshop Manual Issue 5, January 2010
Specifications Maintenance
Transaxle Assembly - Remove for Access
and Install
Removal
1. Disconnect the battery ground cable.
2. Remove the rear undertray (refer to Workshop Manual procedure 01.02.PB - Rear Undertray).
3. Raise the vehicle and install straps to hold it to the lift (refer to Figure 1).
Figure 1
Type
Graziano AM803T transaxle with:
• Integrated Shifter Bellcrack System (Cable Operated)
• Integrated Reverse Switch
• Plate Type Limited Slip Differential
Synchronisers
Triple Cone Syncros on 1st and 2nd, double cone on all
other gears incl. reverse.
Lubrication
Pressure fed system with integrated pump driven by the
input shaft. Filter (filter is serviceable item).
Transaxle Oil
Shell Transaxle 75W/90 (very important that this is the
transaxle type, Do not use Shell Spirax 75W90)
Transaxle Quantity.
Coolant System Quantity. 4 ltr (7 pt / 4.2 US qts)
0.5 ltr (0.9 pt / 0.53 US qts)
Transaxle + Coolant
Quantity 4.5 ltr (7.9 pt / 4.6 US qts)
Gear Ratios
1st 2nd 3rd 4th 5th 6th
3.15:1 1.95:1 1.44:1 1.15:1 0.94:1 0.77:1 (upto VIN
C00525)
0.76:1 (VIN
C00526
Onwards)
Reverse
2.39:1
Differential Locking Ratio
10% Drive, 30% Coast
Torque Figures
DescriptionNm.lb. / ft.
Sump plug 49 36.5
LH Output shaft housing 10 7.5
Halfshaft 70 52
Differential Cover 35 26
Repair Operation Time (ROT)
ItemCode
Transaxle Assembly-Remove for
Access/Refit 07.03.AA
WAR NI NG
WHEN YOU LIFT THE VEHICLE ON A 'TWO POST' LIFT MAKE SURE THAT YOU USE A STRAP TO HOLD THE REAR END OF THE VEHICLE TO THE RAMP. IF YOU
DO NOT, THE VEHICLE CAN FALL OFF THE RAMP AND CAUSE PERSONAL INJURY OR DEATH.
WAR NI NG
THE EXHAUST SYSTEM WILL BE VERY HOT AFTER
OPERATION. LET THE EXHA UST COOL BEFORE YOU
DO WORK. IF YOU DO NO T, PESONAL INJURY CAN
OCCUR.
Page 524 of 947
Manual Transmission (07.03)
Transmission (07.00)7-3-8 Workshop Manual Issue 5, January 2010
32. Install the exhaust front mount.
33. Clean the component mating faces.
34. Apply an applicable sealant to the component mating faces.
35. Install the exhaust centre pipe.
36. Install and tighten the four bolts that attach the exhaust centre pipe to the exhaust front mount.
37. Put the clamps into position on the exhaust pipes.
38. Loosely install the four bolts that attach the exhaust centre pipe to the rear silencer.
39. Align the exhaust assembly.
40. Tighten the two clamps that attach the exhaust centre pipe to the catalytic converters.
41. Install the cross brace.
Figure 24
42. Install and torque the four bolts that attach the cross brace to the rear subframe.
Figure 25
43. Remove the strap that attaches the vehicle to the lift.
44. Lower the vehicle until the wheels are 10 mm above the ground. 45. Connect the battery ground cable.
46. Start the engine.
47. Select first gear and let the wheels to turn for 10
seconds.
48. Stop the engine.
49. Lift the vehicle.
50. Remove the fill plug for the transaxle oil.
51. Make sure that the transaxle oil is level with the opening for the transaxle oil. Add more oil if necessary.
52. Install and tighten the fill plug for the transaxle oil.
53. Install the rear undertray (refer to Workshop Manual
procedure 01.02.PB - Rear Undertray).
Complete Sportshift Hydraulic Kit-Renew
Removal
1. Disconnect vehicle battery.
2. Raise vehicle on ramp and secure with straps.
3. Remove road wheel(s).
4. Remove rear exhaust silencer assembly (see Workshop Manual procedure 09.00.KA Muffler & Bypass Valve
Assembly - Remove for Access & Refit).
5. Roadster Only - Remove centre undertray (see
Workshop Manual procedure 01.02.MB Undertray -
Centre - Renew).
6. Remove bolts (x4), subframe cross brace.
7. Remove centre exhaust mounting bolts (x4).
8. Loosen clamp nuts (x2), release centre pipe from both catalysts.
9. Remove centre pipe and rear exhaust pipes as an
assembly.
WAR NI NG
THE EXHAUST CENTRE PIPE IS HEAVY. GET THE AID OF ONE MORE PERSON
TO DO THE STEP THAT FOLLOWS.
WAR NI NG
TRANSAXLE OIL CAN BE HARMFUL.
OBEY ALL TRANSAXLE OIL MANUFACTURER’S SAFETY INSTRUCTIONS WHEN YO U HANDLE COMPONENTS
THAT HAVE TOUCHED TRANSAXLE OIL.
Repair Operation Time (ROT)
ItemCode
Complete Sportshift Hydraulic Kit-
Renew 07.03.AB
WAR NI NG
ALWAYS DISCONNECT THE BATTERY EARTH (- VE)
TERMINAL FIRST.
WAR NI NG
WHEN YOU LIFT THE VEHICLE ON A 'TWO POST' LIFT MAKE SURE THAT YOU USE A STRAP TO HOLD THE REAR END OF THE VEHICLE TO THE RAMP. IF YOU
DO NOT, THE VEHICLE CAN FALL OFF THE RAMP AND CAUSE PERSONAL INJURY OR DEATH.
Caution
When using a ‘two post’ vehicle ramp, remove the
screws that secure the rear section of the wheel arch
liner to body. Hold back the rear section of the wheel
arch liner to correctly position the foot of the vehicle lift.
Page 528 of 947
Manual Transmission (07.03)
Transmission (07.00)7-3-12 Workshop Manual Issue 5, January 2010
33. Connect vehicle battery.
34. Bleed clutch (see Workshop Manual procedure 08.00.AE Clutch Hy draulic System - Sportshift - Bleed).
35. Test drive vehicle.
36. Raise vehicle on ramp; check transaxle and Sportshift
fluid.Complete Shifter Assembly-Renew-
Roadster Only
Removal
1. Disconnect vehicle battery.
2. Remove Gear position sensor (see Workshop Manual procedure 07.03.AL Sensor - Transmission Assembly -
Sportshift - Renew).
3. Release harness clip from shifter casing.
4. Remove and discard clips (x2) securing hoses into shifter assembly and disconnect hoses (see Figure 1).
5. Remove shifter unit (bolts x6, nut x1) and release from dowels (x2) (s ee Figure 2).
WAR NI NG
ALWAYS CONNECT THE BATTERY EARTH (+VE)
TERMINAL FIRST.
WAR NI NG
TRANSAXLE OIL CAN BE HARMFUL.
OBEY ALL TRANSAXLE OIL MANUFACTURER’S SAFETY INSTRUCTIONS WHEN YOU HANDLE COMPONENTS
THAT HAVE TOUCHED TRANSAXLE OIL.
Repair Operation Time (ROT)
ItemCode
Complete Shifter Assembly-Renew 07.03.AC
WAR NI NG
ALWAYS DISCONNECT THE BATTERY EARTH (- VE) TERMINAL FIRST.
Figure 1
WAR NI NG
TRANSAXLE OIL CAN BE HARMFUL.
OBEY ALL TRANSAXLE OIL MANUFACTURER’S SAFETY INSTRUCTIONS WHEN YO U HANDLE COMPONENTS
THAT HAVE TOUCHED TRANSAXLE OIL.
!
!
Page 529 of 947
Manual Transmission (07.03)
Transmission (07.00)
Issue 5, January 2010 Workshop Manual 7-3-13
6. Remove and discard gasket (see Figure 3).
7. Remove and discard hose O-rings (x3).
Install
1. Install new O-rings to hoses.
2. Clean mating faces and install new gasket to dowels.
3. Ensure alignment of selector mechanism with shifter unit and install shifter unit.
4. Install hoses into shifter unit and install clips.
5. Install harness clip into shifter casing.
6. Install Gear position se nsor (see Workshop Manual
procedure 07.03.AL Sensor - Transmission Assembly -
Sportshift - Renew).
7. Connect vehicle battery.
8. Test drive vehicle.
9. Raise vehicle on ramp; Check transaxle and Sportshift fluid.
10. Lower vehicle on ramp.
Reservoir Tank Assembly-Renew-
Roadster Only
Removal
1. Disconnect vehicle battery.
2. Raise vehicle on ramp.
3. Remove rear undertray (see Workshop Manual procedure 01.02.PB Undertray - Rear - Renew). 4. Remove clips and release reservoir hoses from valve unit
and pump (place drain tray to collect fluid) (see Figure
1).
5. Release reservoir hoses from transaxle mounting clips
(x2) (see Figure 2).
Figure 2
Figure 3
WA R N I N G
ALWAYS CONNECT THE BATTERY EARTH (+VE)
TERMINAL FIRST.
Repair Operation Time (ROT)
!
Figure 1
WA R N I N G
TRANSAXLE OIL CAN BE HARMFUL.
OBEY ALL TRANSAXLE OIL MANUFACTURER’S SAFETY INSTRUCTIONS WHEN YOU HANDLE COMPONENTS THAT HAVE TOUCHED TRANSAXLE OIL.
Figure 2
!
!
Page 530 of 947
Manual Transmission (07.03)
Transmission (07.00)7-3-14 Workshop Manual Issue 5, January 2010
6. Remove bolt, separate bracket clamp and remove reservoir (see Figure 3).
Install
1. Install reservoir and clamp to bracket.
2. Install reservoir hoses to valve unit and pump then install new clips (remove drain tray) (see Figure 1).
3. Install reservoir hoses to clips.
4. Top-up reservoir.
5. Connect vehicle battery.
6. Lower vehicle, turn igniti on ON for 20 seconds to
activate gearbox pump. Turn ignition OFF and raise
vehicle.
7. Top-up reservoir.
8. Install rear undertray (see Workshop Manual procedure 01.02.PB Undertray - Rear - Renew).
9. Lower vehicle on ramp.
Pump Inlet/Valve Body Bleed/Reservoir
Ta n k H o s e s
-Renew-Roadster Only
Removal
1. Disconnect vehicle battery.
2. Raise vehicle on ramp.
3. Remove rear undertray (see Workshop Manual procedure 01.02.PB Undertray - Rear - Renew).
4. Remove clips and release reservoir hoses from valve unit and pump (place drain tray to collect fluid) (see Figure
1).
Figure 3
Figure 1
WAR NI NG
ALWAYS CONNECT THE BATTERY EARTH (+VE) TERMINAL FIRST.
!
!
Repair Operation Time (ROT)
ItemCode
Pump Inlet/Valve Body Bleed/Reservoir
Tank Hoses-Renew 07.03.AF
WAR NI NG
ALWAYS DISCONNECT THE BATTERY EARTH (- VE) TERMINAL FIRST.
Figure 1
WAR NI NG
TRANSAXLE OIL CAN BE HARMFUL.
OBEY ALL TRANSAXLE OIL MANUFACTURER’S SAFETY INSTRUCTIONS WHEN YO U HANDLE COMPONENTS
THAT HAVE TOUCHED TRANSAXLE OIL.
!
Page 531 of 947
Manual Transmission (07.03)
Transmission (07.00)
Issue 5, January 2010 Workshop Manual 7-3-15
5. Release reservoir hoses from transaxle mounting clips (x2) (see Figure 2).
6. Remove clips and release hoses from reservoir (see Figure 3).
Install
1. Install hoses to reservoir and fit new clips.
2. Install reservoir hoses to valve unit and pump. Fit new clips (remove drain tray).
3. Install reservoir hoses to clips.
4. Top-up reservoir.
5. Connect vehicle battery.
6. Lower vehicle, turn igniti on ON for 20 seconds to
activate gearbox pump. Turn ignition OFF and raise
vehicle.
7. Top-up reservoir.
8. Install rear undertray (see Workshop Manual procedure 01.02.PB Undertray - Rear - Renew).
9. Lower vehicle on ramp.
Hydraulic Pump Assembly-Renew-
Sportshift Only
Removal
1. Raise vehicle on ramp.
2. Disconnect vehicle battery.
3. Remove rear undertray (see Workshop Manual procedure 01.02.PB Undertray - Rear - Renew).
4. Disconnect pump multiplug (see Figure 1).
5. Remove ground eye from pump body (bolt x1) (see Figure 2).
6. Clamp reservoir hose.
Figure 2
Figure 3
WA R N I N G
ALWAYS CONNECT THE BATTERY EARTH (+VE)
TERMINAL FIRST.
!
!
Repair Operation Time (ROT)
!
!
Page 532 of 947
Manual Transmission (07.03)
Transmission (07.00)7-3-16 Workshop Manual Issue 5, January 2010
7. Remove clip and release from pump (place drain tray to collect fluid) (s ee Figure 3).
8. Remove HP hose from pump.
9. Remove and discard O-ring from hose.
10. Remove pump from transaxle (bolts x2).
Install
1. Install pump to transaxle.
2. Install new O-ring to HP hose. Install hose to pump.
3. Install reservoir hose to pump then install new clip (remove drain tray).
4. Connect pump multiplug.
5. Install ground eye to pump body.
6. Top-up reservoir.
7. Connect vehicle battery.
8. Lower vehicle, turn igniti on ON for 20 seconds to
activate gearbox pump. Turn ignition OFF and raise
vehicle.
9. Top-up reservoir.
10. Install rear undertray (see Workshop Manual procedure 01.02.PB Undertray - Rear - Renew).
11. Lower vehicle on ramp.
HP Hose Kit-Renew-Roadster Only
Removal
1. Disconnect vehicle battery.
2. Raise vehicle on ramp and secure with straps.
3. Remove road wheel(s).
4. Remove rear exhaust silencer assembly (see Workshop Manual procedure 09.00.KA Muffler & Bypass Valve
Assembly - Remove for Access & Refit).
5. Remove centre undertray (see Workshop Manual procedure 01.02.MB Undertray - Centre - Renew).
6. Remove bolts (x4) and subframe cross brace.
7. Remove centre exhaust mounting bolts (x4) (see Figure 1).
8. Loosen clamp nuts (x2), release centre pipe from both catalysts.
9. Remove centre pipe and rear exhaust pipes as an
assembly.
10. Remove bolts/washers (x4), tunnel heatshield to body, remove heatshield.
11. Remove bolts (x8), shear plate to body, remove shear plate.
12. Remove bolt securing earth lead to transaxle.
13. Mark drive shaft to differential flanges for assembly purposes.
14. Remove and discard Allen bolts (x12), collect plates (x6), drive shaft flanges to transaxle.
WAR NI NG
TRANSAXLE OIL CAN BE HARMFUL.
OBEY ALL TRANSAXLE OIL MANUFACTURER’S SAFETY INSTRUCTIONS WHEN YOU HANDLE COMPONENTS
THAT HAVE TOUCHED TRANSAXLE OIL.
WAR NI NG
ALWAYS CONNECT THE BATTERY EARTH (+VE) TERMINAL FIRST.
Repair Operation Time (ROT)
ItemCode
HP Hose Kit-Renew-Roadster Only 07.03.AH
WAR NI NG
ALWAYS DISCONNECT THE BATTERY EARTH (- VE) TERMINAL FIRST.
WAR NI NG
WHEN YOU LIFT THE VEHICLE ON A 'TWO POST' LIFT MAKE SURE THAT YOU USE A STRAP TO HOLD THE
REAR END OF THE VEHICLE TO THE RAMP. IF YOU
DO NOT, THE VEHICLE CAN FALL OFF THE RAMP AND CAUSE PERSONAL INJURY OR DEATH.
Figure 1
!
Page 534 of 947
Manual Transmission (07.03)
Transmission (07.00)7-3-18 Workshop Manual Issue 5, January 2010
28. Remove and discard clips (x2) securing hoses into shifter assembly and disconnect hoses (see Figure 6).
29. Remove and discard clips (x3) securing hoses into valve block and disconnect hoses (see Figure 7).
30. Release hoses from support clips (x3) (see Figure 8).Install
1. Install hoses to support clips.
2. Install hoses into shifter unit and install clips.
3. Install hoses to valve block and install new clips.
4. Raise transaxle, install harness clip to subframe.
5. Connect transaxle breather pipe.
6. Raise transaxle to fitted position.
7. Install transaxle mounting brackets and hydramounts, install and torque tighten new bolts (x8).
8. Align hydramounts to subfra me, lower lifter, install and
torque nuts. Remove lifter.
9. Position reservoir to bracket and fit clamp (bolt x1).
10. Position reservoir hose and secure clips.
11. Remove plugs, connect and torque oil cooler unions.
12. Apply thread lock to new Allen bolts.
13. Align drive shafts to transaxle flanges, clean and install plates (x6), install and torque tighten Allen bolts (x12).
14. Position earth lead to transaxle, install and torque tighten bolt.
15. Install shear plate, install bolts (x8), tighten bolts to correct torque.
16. Install tunnel heatshield, install bolts/washers (x4), tighten bolts to correct torque.
17. Install centre and rear exhaust pipe assembly, align to both catalysts. tighten clamp nuts to correct torque.
18. Install bolts (x4) into centre mounting.
19. Install subframe cross brace, install bolts (x4) and torque.
20. Install rear exhaust silencer assembly (see Workshop Manual procedure 09.00.KA Muffler & Bypass Valve
Assembly - Remove for Access & Refit).
21. Install centre undertray (see Workshop Manual procedure 01.02.MB Undertray - Centre - Renew).
22. Install road wheel(s).
23. Lower vehicle on ramp, remove securing straps.
24. Connect vehicle battery.
25. Test drive vehicle.
26. Raise vehicle on ramp; check transaxle and Sportshift fluid.
27. Lower vehicle on ramp.
Figure 6
WAR NI NG
TRANSAXLE OIL CAN BE HARMFUL.
OBEY ALL TRANSAXLE OIL MANUFACTURER’S SAFETY INSTRUCTIONS WHEN YOU HANDLE COMPONENTS THAT HAVE TOUCHED TRANSAXLE OIL.
Figure 7
Figure 8
!
!
!
WAR NI NG
ALWAYS CONNECT THE BATTERY EARTH (+VE) TERMINAL FIRST.