engine AUDI A3 2012 Owner´s Manual

250 Emergency sit uat ions
2. Otherwise apply the hand brake and shift
into idle gear if your vehicle has manua l
transmission, and put the selector lever
into P position if your vehicle has auto­
matic transmission.
3 . For both vehicles switch off all consumers
and the ig nition .
Connectin g/disco nn ecting th e jumper
cable
4 . Connect one end of the red jumper cable
to the positive term inal
(D ¢ fig . 193 of
the discharged battery @ ¢0
in General
information of starting assistance on
page 249 .
5. Connect the other end of the red jumper
cab le to the positive termina l@ of the
booster battery @.
6 . Connect one end of the black jumper ca­
b le, preferably at the ground point. Other­
wise, connect it to the negative terminal
@ of the booster battery @.
7 . Connect the other end of the black jumper
cab le to the
ground po int (bolt head )©
in your v ehi cle @ .
8. Route the jumper cables so that they can­
not catch in any rotating parts in the en­
gine compartment.
Starting the engine
9 . Start the engine of the vehicle provid ing
assistance and allow it to run at idle .
10. Now start the eng ine o f the vehicle w ith
the discharged battery, wa it for two to
three minutes unti l the engine "runs"
smoothly .
11. If the engine does not start: Stop trying
after
10 seconds and then try again after
about
30 seconds.
12 . In the veh icle that has received start as­
sistance, turn on the heater blower and
the rea r window heat ing to eliminate any
voltage peaks when disconnecting. Driv­
ing lights must be swi tched off!
13. Disconnect the cable whi le the engine is
running exact ly in
reverse order to that
described in¢
page 250, Connecting/dis­
connecting the jumper cable.
When do ing so, make sure that the cable cannot con­
tact rotating engine parts.
14. Turn the heater b lower and the rear w in-
dow heating off again .
The battery is vented to the outside to prevent gases from entering the vehicle interior .
Make sure that the jumper clamps are we ll
connected with thei r
metal ports in full con­
tact
with the battery terminals .
A WARNING
To avoid serious personal injury and dam­
age to the vehicle, heed all warnings and
instructions of the jumper cable manufac­
turer. If in doubt, call for road service.
- Jumper cables must be long enough so
that the veh icles do not touch.
- When connecting jumper cables, make sure that they cannot get caught in any
mov ing parts in the engine compart­
ment.
- Before you check anything in the engine
compartment, always read and heed all
WARNINGS ¢page 187, Engine com­
partment.
{CT) Note
Improperly connected jumper cab les can
damage or destroy the generator .
- Do not use the battery negative terminal
for jump start ing or a malfunct ion could
occur in the vehicle electrical system.
- Always connect POSITIVE(+) to POSI-
TIVE(+), and NEGATIVE(-) to NEGATIVE
( - ) term inal.
- Check that all screw p lugs on the battery
cells are screwed in firm ly . If not, tighten
plugs prior to connecting clamp on nega­
tive batte ry term inal.
- Please note that the procedure for con­
necting a jumper cable as described
above applies specifically to t he case of
your vehicle being jump st arted. When
yo u are g iving a jump sta rt to another ve­
hicle, do
not connect the minus( -) cable
to the minus (-) terminal on the dis­
charged battery@¢fig.193 . Instead,

securely connect the minus(- ) cable to
either a massive metal component that
i s firm ly bolted to the eng ine b lock or to
the engine block itself. If the battery
that is being charged does not ve nt to
the outside, escaping battery gas cou ld
i gnite and explode!
Emergency towing
with commercial tow
truck
General hints
Your Audi requires special handling for tow­
ing .
The fol low ing information is to be used by
commercial tow truck operators who know how to ope rate their equipment safe ly.
- Never to w your Audi, towing will cause
damage to the engine and t ransmission.
- Never wrap the safety chain s or winch ca ­
bles around the br ake lines.
- To pre vent unnecessary damage , you r Audi
must be transported with a car carrie r (flat
bed truck ).
- To load the vehicle on to the flat bed, use
the towing loop found in the veh icle tools
and attach to the front or rear anchorag e
¢page 251 and ¢page 252.
..&, WARNING
A vehicle being towed is not saf e for pas­
senge rs. Never a llow anyone to r ide in a
vehicle being towed, for any re ason.
Emergenc y situ ation s 251
Front towing loop
Do not install the front towing loop until it is
needed .
Fig . 194 Fro nt bu mper: re m ov ing t he cover ca p
Fig. 195 Fro nt bump er: s crew ing in t he tow ing loo p
The towing loop fits into the threaded hole lo ­
cated on the right s ide of the front b umper
and covered by a sma ll cover when not in use .
Note that the towing loop has
a left-h and
thread !
.,. Remove the tow ing loop from the vehicle
too lki t¢
pag e 234 .
.. Press on the bottom edge of the cover cap
to disengage and take it out of the bumper.
T he cap rema ins connected to the bumper
¢fig . 194 .
.,. Inser t the tow ing loop into the threaded
hole
<=> fig . 195 and tur n it all the way in un ­
til it is seated securely, then tighten it with
t h e wheel bolt w rench .
When it is no longer needed, unscrew the
towing loop and put it back into the o n-boa rd
toolk it . Make su re to have the towing loop
stored in the vehicle at all times .

-The vehicle should never be lifted or jacked
up from underneath the engine oil pan , the
transmission housing , the front or rear
a x le or the body side members. This could
lead to ser ious damage.
- Use lifting equipment with padded contact
surfaces to avo id damage to the underbody
or chassis frame.
- Alternatively, cover the contact surfaces on
workshop hoist or floor jack w ith rubber
pads b efore lifting.
- Before dri ving over a workshop hoist, check
that the vehicle weight does not exceed the
permissible lifting capacity of the hoist .
- Before dr iving over a workshop hoist, en­
sure that there is sufficient clearance be­
tween the hoist and low parts of the vehi­
cle .
A WARNING
To r educe the ris k of seriou s injury a nd ve­
hicle da mage:
- Always lift the veh icle only at the spec ial
wor ks ho p hoi st and floor j ack lift p oin ts
ill ustra te d
c:;>page 253, fig. 199 and
c:;>page 253, fig . 20 0.
- F ailure to l ift the vehicl e at th ese poi nts
cou ld ca use the ve hicle to t ilt or fall from
a lift if there is a c ha nge in vehicle wei ght
dist rib ution and balance . This might hap ­
pen, for example, when heavy c ompo­
nents such as the e ngine bloc k or t rans­
mission are removed.
- W hen remov ing s uch heavy c omponents,
anchor veh icle to h oist or add corre­
sponding we ights t o maintain the center
of g rav ity. Oth erwise, th e veh icle m ig ht
t il t o r slip off the hois t, causing serio us
p ers onal in ju ry.
Emergency situations 253
Lifting with workshop hoist and with
floor jack
T he vehicle may only be lifted at the li~ing
p oi nt s illus tra ted.
..,
---------~1::
Fig. 199 Front lifting point
Fig. 200 Rear lifting point
.,. Read and heed WAR NIN G c:;> &. in Impor ­
tant safety precautions on page 253 .
.,. Locate lifting points c:;> fig. 199 c:;> fig . 200 .
.,. Adjust lifting arms of workshop hoist or
fl oor jack to matc h ve hicle lift ing poi nts.
I
.,. Insert a rubbe r pad between the floo r jac k/
workshop hoist and t he lift ing poin ts .
If you must l ift your vehicle with a floor jack
to work underneath, be sure the vehicle is
safely supported on stands intended for this purpo se .
Front lifting point
The lifting poi nt is located o n the floo r pan re­
inforcement about at the same leve l as the
jac k mounti ng po int
c:;> fig. 199. Do not lift
the vehicle at the vertical sill reinforcement .
Rear lifting point
The liftin g point is located on the vert ica l rein­
forcement of the lower s ill for the on board
jack
c:;> fig. 200. ..,.

254 Emergency situations
Lifting with vehicle jack
Refer to"* page 239.
(D Note
-Be aware of the following points before
lifting the vehicle:
-The vehicle should never be lifted or
jacked up from underneath the engine
oil pan, the transmission housing, the
front or rear axle or the body side members. This could lead to serious
damage.
- To avoid damage to the underbody or
chassis frame, a rubber pad must be
inserted between the floor jack and
the lift points.
- Before driving over a workshop hoist,
check that the vehicle weight does not
exceed the permissible lifting capacity
of the hoist.
- Before driving over a workshop hoist,
ensure that there is sufficient clear­
ance between the hoist and low parts
of the vehicle.

General information Explanation of
technical data
Som e of t he technical data listed in this man ­
ual requires further explanation .
The technical data for your vehicle is listed in
the charts starting on
Q page 257. This sec ­
tion provides general information, notes and
r estr ictions wh ich app ly to this data.
Vehicle identification
The key data a re given on the vehicle identifi­
c a tion number ( VIN) pla te and the vehicle da­
ta sticker.
F ig. 201 Veh icle Ident ific atio n Num ber (VIN) p late: lo ­
cation o n dri ver"s s ide das h pa nel
Fi g. 2 02 The ve hicle iden tifi cat ion label -inside the
l u ggage co mpartme nt
The Vehicle Identification Number (VIN)
is located on the d river's side so tha t it is v is i­
b le from the o utside throug h the windshield -
see
c!) fig. 201.
The vehicle identification label
i s located in the luggage compartment in t he
sp are wheel well. General inform
ation 255
The labe l
Q fig. 202 shows the fo llow ing vehi ­
cle data :
(D Product io n cont ro l no.
@ Vehicle identification no .
@ Type code number
@ Type designat ion/engine o utp ut in K ilo-
watts
® Engine and t ransm ission code letter
@ Pa in t no./ In te rior
(J) Optional equipment no.'s
Vehicle data 2 to 7 are a lso fo und in your W ar­
ranty
& Maintenance booklet .
The safety compliance sticker
is your assurance that your new vehicle com­
plies wi th a ll applicab le Fede ral Mot or Vehicle
S afety S tand ards which were in effect at the
time the ve hicle was ma nufactured. You can
find this sticke r on the left doo r jamb. It
shows the mo nth and yea r of prod uction and
the vehicle identificat ion number of yo ur vehi­
cle (perforation) as well as the Gross Vehicle
Weight Rating (GVWR) a nd the Gross Axle
Weight Rating (GAWR) .
The high voltage warning label
is located on the lock carrie r.
The spark ignition system complies with
the Canadian standard ICES-002.
Weights
Gr oss Vehicle Weight Rating
The Gross Vehicle Weight Rat ing (GVWR), and
the G ross Axle Weight Rating (GAWR) for
front and rear are listed on a sticker on the left door jamb.
The Gross Vehicle Weight Rat ing includes the
weight of the bas ic vehicle plus fu ll fuel tank,
o il and coo lant, plus maximum load, which in­
cludes passenger we ight (150 lbs/68 kg per
designated seating position) and luggage
weight .

Data 257
Data
200 hp, 2.0 liter 4-cyl. turbo gasoline engine
Applies to vehicles: with 2.0 liter TFS! 4-cyl. gasoline engine,
Engine data Maximum outpu t SAE ne t
M aximum torque SAE net
No . of cylinders
Displacement
Stroke
Bore
C ompression ratio
Fuel
Dimensions (approx .)
L eng th (wit h license pl ate brac ket)
Width (across mirrors) He igh t (unladen, incl . roof r ails) 200@ 5100
-6000
hp@r pm
lb-ft@ rp m
-~--
CID (cm3
)
in (mm)
in (mm)
---·
207 @ 1700 - 5000
4
121 (1984)
3 .65 (92 .8)
3.25 (82 .5)
9 .6: 1
Premium unleaded
(91 AKI) Recommended for maxi­
mum engine performance. Further details ¢page 189,
Gasoline
in (mm) 168.9 (42 92)
in (mm) 78.5 (1995)
in (mm) 56.0 (1423)
T urning circle diameter (curb to curb) ft. (m) 35.1 (10.7)
Capacities (approx.)
Fuel tank
- Total capacity
- Reserve (of total capacity)
Windshield washer fluid container Engine oil with filter change front wheel
drive
a ll whee l drive gal/liters
14.63 / 55.0
g al/liters 15.8 5 / 60 .0
gal/liters 1.8/7.0
qu arts/ liters 3 .1 / 3 .0
quarts/li ters 4.8 / 4.6
•
•

258 Data
140 hp, 2.0 TOI liter 4-cyl. turbo clean diesel
engine
App lies to vehicles: with 2.0 liter TD! 4-cyl. clea n diesel engine,
Engine dat a
Maximum ou tpu t SA E ne t hp@rpm 140 @42 00
Maximum torque SAE net lb-ft@ rpm 236@ 1750 -2500
N o. of cylinders 4
Displacement CID (cm3
) 120.1 ( 1968)
Stroke i
n (mm) 3.7 6 (9 5.5)
Bore i
n (mm) 3.19 (8 1.0)
Compression ratio 16.5: 1
Fuel ULSD Diesel No . 2 Further details c::> page 190, Diesel fuel
Dimensions (approx .)
Length (with license plate bracket) in (mm)
Width (across mirrors) in (mm)
Height (unladen, incl. roof ra ils) in (mm)
T urning circl e diameter (curb to curb) ft. (m)
Capacities (approx.)
Fuel tank
- Total capacity
- Reserve (of total capacity)
Windshield washer fluid container
Engine oil
with filter change
168.9 (4 292)
78.5 (1995)
56 .0 (1423)
35.1 (1 0.7)
gal/li te rs 1 4 .63 / 55.0
ga I/liters 1.8/7 .0
quarts/liters 3.1 / 3.0
quarts/liters 4 .2 I 4.0

Consumer Information
Warranty coverages
Your Audi is covered by the following war­
ranties :
- New Vehicle Limited Warranty
- Limited Warranty Against Corrosion Perfo-
ration
- Emissions Control System Warranty
- Emissions Performance Warranty
- California Emissions Control Warranty (USA
vehicles only)
- California Emissions Performance Warranty
(USA vehicles only)
Detailed information regarding your warran ­
ties can be found in your
Warranty & Mainte­
nance Booklet .
Operating your vehicle
outside the U.S.A. or
Canada
Government regulations in the United States
and Canada require that automobiles meet
specific emission regulations and safety
standards. Therefore, veh icles built for the
U.S.A. and Canada differ from vehicles sold in
other countries .
If you p lan to take your vehicle outside the
continental limits of the United States or Can­
ada, there is the possibility that
- unleaded fuels for vehicles with cata lytic
converter may not be available;
- fuel may have a considerably lower octane
rating. Improper fuel may cause engine
damage;
- service may be inadequate due to lack of
proper service facilities, tools or testing
equipment;
- replacement parts may not be readily availa­
ble.
- Navigation systems for vehicles built for the
U.S.A. and Canada will not necessari ly work
in Europe, and may not work in other coun­
tries outside of North America.
Consumer Information 259
Audi cannot be re sponsible for mechanical
damage that could result from inadequate
fuel, service or parts availability.
Q) Note
Audi cannot be responsible for mechanical
damage that could result from inadequate
fuel, serv ice or parts availab ility.
Audi Service Repair
Manuals and Literature
Audi Offic ial Factory Service Manuals and Lit­
erature are published as soon as possible after
model introduction. Service manuals and lit­
erature are available to o rder from the Audi
T echnical Literature Ordering Center at:
www.audi.techliterature.com
Maintenance
General
Your vehicle has been designed to help keep
maintenance requirements to a minimum.
However, a certain amount of regu lar mainte­
nance is still necessary to assure your vehicle's
safety, economy and re liability .
For detailed vehicle maintenance consult your
Warranty
& Maintenance booklet.
Under difficult operating conditions, for ex­
amp le at extreme ly low outside temperatures,
in very dusty regions , when towing a trailer
very frequently, etc., some service work
shou ld be performed between the intervals
specified. This applies particularly to:
- oil changes, and
- cleaning or rep lacing the air fi lter.
@ For the sake of the environment
By regularly maintaining your veh icle, you
help make sure that emission standards
are maintained, thus minimizing adverse
effects on the environment.
•
•

260 Consumer Inf ormation
Important considerations for you and
your vehicle
The increasing use of e lectronics, sophisticat­
ed fue l injection and emission control sys­
tems, and the generally increasing technical
comp lexity of today's automob iles, have
steadi ly reduced the scope of maintenance
and repairs which can be carried out by vehicle
owners .
Also , safet y and en vironm ental con­
cerns p lace very strict lim its on the nature of
repairs and adjustments to eng ine and t rans­
miss ion parts which an owner can pe rform .
Ma intenance, adjustments and repa irs usually
require special tools, testing dev ices and oth­
e r equipment avai lab le to specia lly t ra ined
workshop personne l in order to assure prope r
pe rformance, reliab ility and safety of the vehi­
cle and its many systems.
I mp roper ma intenance, adjus tments and re­
pa irs can impai r the operation and reliab ility
of your vehicle and even void you r vehicle war­
ranty . There fore, proof of servicing in accord­
ance wit h the ma intenance sched ule may be a
condition for upholding a poss ible warranty
claim made within the warranty period.
Above all, operational safety can be adversely
affected, c reating unnecessary risks for you
and your passengers .
I f in do ubt about any serv icing, have it done
by your authorized A udi dealer or any other
p roperly equipped and qualified workshop .
We strong ly urge you to give yo ur authorized
Aud i dealer the opportunity to perform all
schedu led maintenance and necessary repairs.
Your dea le r has the facilities, or iginal parts
and trained spec ialists to keep your vehicle
running prope rly .
Performing lim ited maintenance yourself
The follow ing pages describe a limited num­
ber of procedures which can be performed on
your ve hicle w ith ordi nary too ls, should the
need a rise and trained pe rsonnel be unavaila­
b le. Before perfo rming any of these proce­
du res, always tho roughly read a ll of the app li­
cab le text and ca re fully follow the instruc - tions given
. Always r igo ro usly observe the
WARNINGS provided.
Bef ore you che ck anything in the engine
compartment , alway s read and h eed all
WARNINGS
¢ & and ¢ & in Working in the
engine comportment on page 194 .
A WARNING
--Ser ious persona l in ju ry may occur as a re -
sult of improperly performed mainte­ nance, ad justments or repa irs.
-Always be extremely care ful when work­
ing on the vehicle. Always follow com­
mo nly accepted safety pract ices and gen­
era l common sense. Never r isk personal
in jur y.
- Do not attempt any of the mainte nance,
checks or repairs descr ibed o n the fol­
lowing pages if you are not fu lly fam iliar
wit h these or ot her procedures with re­
spect to the ve hicl e, or are uncerta in how
to procee d.
- D o not do a ny work wi thou t the prope r
tools and equipment . Have the necessary
work done by your author ized A udi deal ­
er or anothe r properly equipped and
qualified wor kshop.
- The engine compa rtment o f any motor
vehicle is a potentially hazardous area.
N ever reach into the area aro und or
touch the rad iator fan. It is temperature
control led and can sw itch on suddenly -
even when the engine is off and th e igni­
tion key has been removed. The ra diator
fan switc hes on automat ica lly w hen the
coo la nt re aches a certai n tempera tu re
a nd will cont inue to ru n until the coo lant
tempera ture drops .
- Always remove the ig nition key befo re
an yone gets unde r the veh icle.
- Always suppor t your ve hicle with safety
s tands i f it is ne cessary to work under­
neath the vehicle. The jack s upplied with
the vehicle is not adequate for this p ur­
pose and co uld co llapse causing serio us
personal injury.

-If you must work underneath the vehicle
with the whee ls on the ground, always
make sure the vehicle is on level ground,
that the wheels are always secu rely
blocked and tha t the eng ine cannot be
started.
- Always make sure the transm ission se­
lector lever (automatic transmiss ion) is
in "P" (Pa rk position) (a utomat ic trans­
mission) or Neutral (manual transmis­
sion) and the hand brake is fi rm ly ap­
plied.
@, For the sake of the environment
- Changing the eng ine settings w ill ad­
versely affect em ission levels. This is det­
rimental to the environment and increas­
es fue l cons umption.
- Always obse rve env ironmental regula­
tions when d ispos ing of old engine oil,
used b rake fluid, dirty engine coolant,
spent batteries or worn out tires .
- Undeployed airbag modules and preten­
s ioners might be classified as Perchlo­
rate Mate rial -special handling may ap­
ply, see www.dtsc.ca.gov/hazardous­
waste/perchlorate. When the veh icle or
parts of the restraint system includ ing
airbag modules safety belts with preten­
s ioners are scrapped, all appl icable laws
and regulations must be observed. Your
autho rized Audi dea le r i s familiar w ith
these req uirements and we recommend
that yo u have your dea le r perform this
service for you.
Additional accessories, modifications and
parts replacement
Additional accessories and parts
replacement
Always consult an authorized Audi dealer be­
fore purchasing accessories .
Your vehicle incorporates the latest safety de­
sign features ensuring a high standard of ac­
tive and passive safety .
Consumer In formation 26 1
This safety could be compromised by non-ap ­
proved changes to the vehicle . For this reason,
if parts have to be replaced, please observe
the following points when installing add ition­
al accessories:
Approved Audi accessories and genuine Audi parts are available from authorized Audi deal­
ers.
T hese dea lers a lso have the necessary facili­
ties, tools and trained specialists to install the parts and accessories properly .
_& WARNING
Using the wrong spare parts non-approved
accessories can cause damage to the vehi­
cle and serious personal injury.
- Use on ly accessories expressly approved
by Audi and genu ine Audi spare parts
- These parts and accessories have been
specially designed to be used on your ve­
hicle.
- Never install accessor ies such as tele­
phone cradles or beverage ho lders on air­
bag covers or within the airbag deploy­
ment zones. Do ing so will increase the
ris k of injury if a irbags are triggered in an
accident!
- Before you check anything in the engine
compa rtment, always read and heed a ll
WARNINGS
<:!)page 187.
(D Note
-If items other than genu ine Audi spare
parts, add-on equipment and accessory
items are used o r if repair wo rk is not
performed accord ing to specified meth­
ods, this can resu lt in severe damage to
your vehicle's engine and body (such as
corrosion) and adve rsely affect yo ur vehi­
cle 's warranty.
- If emergency repairs must be performed
elsewhere, have the vehicle examined by
an authorized Audi dealership as soon as
possible.
- The manufacturer cannot be held liable
for damage wh ich occ urs due to failure
to comply with these stipulations.
•
•