engine AUDI A4 1996 B5 / 1.G APB Engine Motronic Syst

01-92

- Allow engine to idle for a few minutes: Coolant
temperature at least 80 C.
Notes:

When the PRINT button is pressed the current
display will be printed out.
Press C button before selecting further display
groups.

- If readouts in all display fields match
specifications, press button.
Rapid data transfer
HELP
Select function XX

Indicated on display
- Press buttons -0- and -6- to select function "End Output".
Rapid data transfer
HELP
06 - End Output

Indicated on display
- Confirm with -Q- button.
Rapid data transfer
HELP
Select function XX

Indicated on display
Pa
ge 112 of 166 Motronic s
ystem, On Board Dia
gnostic
(OBD
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU04.01.1

01-93

Control module, coding


Notes:

If the correct coding for the vehicle is not
displayed, or if the control module has been
replaced, the control module must be coded.

- Connect vehicle diagnostic, testing and
information system VAS 5051 or VAG1551 scan
tool and select engine electronics control
module by entering address word "01" Page 01
-9 . When doing this the ignition must be
switched on.
8D0907551.. 2.7L V6/5VT
G 0002
Codin
g 06711
WSC 06388

The display of VAG1551 will show the control module coding (example).
The relevant vehicle coding must be displayed, note coding table Page 01
-94
.
Pa
ge 113 of 166 Motronic s
ystem, On Board Dia
gnostic
(OBD
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU04.01.1

01-94
Coding variations of Engine Control Module (ECM)
Country/
Emission standard Power train /
Additional systems Transmission
Type of
vehicle
00 = ------------------ 0 = ------------------ 0 = ------------------ 0 = ---------
---------
01 = ------------------ 1 = ------------------ 1 = 6-speed manual
transmission 1 = A4
02 = ------------------ 2 = ------------------ 2 = ------------------ 2 = ---------
---------
03 = ------------------ 3 = ------------------ 3 = ------------------ 3 = ---------
---------
04 = ------------------ 4 = ------------------ 4 = ------------------ 4 = ---------
---------
05 = ------------------- 5 = ------------------ 5 = 5-speed automatic
transmission (ZF)
(5HP24) 5 = ---------
---------
06 = USA; TLEV (Exhaust emission
standard) NOTE: Vehicles with Leak
Detection Pump (LDP) 6 = All-wheel drive without Anti Slip
Regulation (ASR)/Electronic Stability Program
(ESP) (with CAN-Bus system) 6 = ------------------ 6 = ---------
---------
07 = ----------------- 7 = All-wheel drive with Anti Slip Regulation
(ASR)/Electronic Stability Program (ESP)
(with CAN-Bus system) 7 = ------------------ 7 = ---------
---------
Notes:
Pa
ge 114 of 166 Motronic s
ystem, On Board Dia
gnostic
(OBD
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU04.01.1

01-97

Read Measuring Value Block


Test requirements

Coolant temperature at least 80 C

Electrical consumers switched off (radiator
fan must not run during the check)
A/C switched off

- Connect vehicle diagnostic, testing and
information system VAS 5051 or VAG1551 scan
tool and select engine electronics control
module by entering address word "01" Page 01
-9 . When doing this the engine must be
idling.
Rapid data transfer
HELP
Select function XX

Indicated on display:
- Press buttons -0- and -8- to select function "Read Measuring Value
Block" and confirm entry with -Q- button.
Read Measuring Value Block Input displa
y group number XXX

Indicated on display
Pa
ge 118 of 166 Motronic s
ystem, On Board Dia
gnostic
(OBD
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU04.01.1

01-100

The readiness code will be reset to "1 1 1 1 1
1 1 1" if:

The DTC memory was erased
A new Engine Control Module was installed
If the voltage supply has been disconnected
from the Engine Control Module (ECM)
In this case the readiness code must be
generated Page 01
-105
.
During driving operation in various load
conditions, exhaust relevant tests are performed
by the control module within a "short trip" and
readiness code is generated on its own. In this
case, however, concluding control possibilities
are not available, meaning that it will not be
indicated whether all positions of the readiness
code are set to "0."
Pa
ge 121 of 166 Motronic s
ystem, On Board Dia
gnostic
(OBD
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU04.01.1

01-101

Readiness code, checking


Test sequence

- Connect vehicle diagnostic, testing and
information system VAS5051 or VAG1551 scan
tool to vehicle and select Control module for
engine electronics "Address Word" 01 Page
01
-9 . The ignition must be switched on.
Rapid data transfer
HELP
Select function XX

When indicated on display
- Press buttons -0- and -8- to select "Read Measuring Value Block" and
press -Q- button to confirm input.
Read Measurin
g Value Block
Q
Input displa
y group number XXX

When indicated on display
- Press buttons "086" for "display group number 086" and press -Q-
button to confirm input.
Read Measuring Value Block 86
1
2
3
4

When indicated on display
- Check readiness code in display field 1

Specified value: 0 0 0 0 0 0 0 0
Pa
ge 122 of 166 Motronic s
ystem, On Board Dia
gnostic
(OBD
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU04.01.1

01-106

Work step 1: Check DTC memory

- Connect Vehicle Diagnostic, Test and
Information system VAS5051 or VAG1551 scan
tool to vehicle and select control module for
engine electronics using "address word" 01
Page 01
-9 . The ignition is switched on.
Rapid data transfer
HELP
Select function XX

When indicated on display
- Press buttons -0- and -2- to select function "Check DTC Memory" and
press -Q- button to confirm input.
X DTC reco
gnized!

Number of stored DTCs or "No DTC recognized" will be indicated on
display.
If a DTC is stored:
If no DTC is stored: - Repair malfunction, erase DTC memory. Road test vehicle and then re-
check DTC memory as a control measure.
-
Press button.
Pa
ge 128 of 166 Motronic s
ystem, On Board Dia
gnostic
(OBD
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU04.01.1

01-108

Work step 3: Adaptation Throttle Valve
Control Module to Engine Control Module
(ECM)

Test requirements

Ignition switched on.
Rapid data transfer
HELP
Select function XX

When indicated on display
- Press buttons "04" for the function "Basic Setting" and press Q button
to confirm input.
System in Basic Settin
g
Q
Input displa
y group number XXX

When indicated on display
- Input "060" for "display group number 60" and press Q button to
confirm input.
System in Basic Setting 60
1
2
3
4

When indicated on display
- Check readiness code in display field 3 and 4:
Pa
ge 130 of 166 Motronic s
ystem, On Board Dia
gnostic
(OBD
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU04.01.1

01-110
If specified value "ADP. OK" is obtained:

- Press -C- button.

Work step 4: Diagnosis of EVAP canister
purge regulator valve

- Start engine (vehicles with manual transmission
depress clutch pedal)

Note:
If necessary, ECM must be re-selected with the
"address word" 01 following engine start, and the
function "initiate basic setting" selected with "04."

Test requirements

Engine at idle
Coolant temperature > 85 C (display group
4, display field 3)
Rapid data transfer
HELP
Select function XX

Indicated on display
- Press button -0-, -7- and -0- to select "display group number 070" and
confirm input with -Q- button.
System in Basic Setting 70

When indicated on display
Pa
ge 133 of 166 Motronic s
ystem, On Board Dia
gnostic
(OBD
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU04.01.1

1
2
3
4
Note:
If test is not initiated or the display jumps from "Test ON" to "Test OFF"
slightly accelerate engine briefly, test will be repeated. - Check specified value in display field 4:
Pa
ge 134 of 166 Motronic s
ystem, On Board Dia
gnostic
(OBD
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU04.01.1