brake AUDI A4 1996 B5 / 1.G Parking Brake Lever Workshop Manual
[x] Cancel search | Manufacturer: AUDI, Model Year: 1996, Model line: A4, Model: AUDI A4 1996 B5 / 1.GPages: 6, PDF Size: 0.11 MB
Page 1 of 6

46-38
Parking brake lever, removing
and installing
Additional information
Repair Manual, Body-Exterior
Repair Manual, Body-Interior
Removing
- Remove rear part of center console.
Repair Manual, Body
-Interior, Repair Group
68
Installing - Remove hex nuts -1-.
- Use screwdriver to push parking brake cable inward, and remove
parking brake lever.
- Install parking brake cable into adjustment bracket.
- Tighten hex nuts -1- to 25 Nm (18 ft lb).
Pa
ge 1 of 6 Parkin
g brake lever, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU03.46.5
Page 2 of 6

Repair Manual, Body
-Interior, Repair Group 68
- Adjust parking brake page 46
-39
.
- Install rear part of center console.
Pa
ge 2 of 6 Parkin
g brake lever, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU03.46.5
Page 3 of 6

46-39
Parking brake, adjusting
Additional information
Repair Manual, Body-Exterior
Repair Manual, Body-Interior
Note:
Re-adjusting the parking brake is not generally
necessary because of the automatic adjustment
of the rear brakes. It is only necessary to re-set
the parking brake when the cables or brake
calipers have been replaced.
The brake system must be bled and must be
operating properly.
- Depress brake pedal firmly at least once.
Parking brake lever released (all the way
down)
- Remove ashtray for rear passenger
compartment.
Repair Manual, Body
-Interior, Repair Group
Pa
ge 3 of 6 Parkin
g brake lever, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU03.46.5
Page 4 of 6

68
- Remove any plastic parts at compensating bar;
they do not need to be re-installed.
- Use size 2 screwdriver to lock compensating bar in place to prevent it
from turning (shown without center console to simplify illustration).
Pa
ge 4 of 6 Parkin
g brake lever, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU03.46.5
Page 5 of 6

46-40
Note:
On all-wheel-drive vehicles, the parking brake
cable adjusting components are located in front
of the lower rear control arms.
On front-wheel-drive vehicles they are located
in the tunnel on the underside of the vehicle.
- Remove locking component -D-.
- Counter hold hex -E- using 13 mm open end wrench and turn adjusting
nut -C- in to stop.
- Slide cable adjuster together (arrow -B-).
- Back off adjusting nut until slot for locking component is visible.
- Install locking component.
- Pull both cable sleeve adjusters apart evenly until cables are
tensioned.
While doing this, the lever must not lift off at the brake caliper.
- Remove screwdriver from compensator and apply parking brake firmly
3 times.
Pa
ge 5 of 6 Parkin
g brake lever, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU03.46.5
Page 6 of 6

46-41
Note:
The colored O-ring -1- must not be visible. This ensures that the parking
brake cable adjustment mechanism is sufficiently protected against dirt
and water spray.
- Check parking brake tension and adjust fine adjustment -A- in or out if
necessary.
- Check distance -a-.
Lever should not contact brake caliper
Gap should be visible but no wider than 1.5 mm (0.059 in.)
Pa
ge 6 of 6 Parkin
g brake lever, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU03.46.5