engine oil AUDI A4 1997 B5 / 1.G AWM Engine Lubrication System Components Workshop Manual

17-1


Lubrication system
components, removing and
installing

Note:

If large quantities of metal shavings or particles
are found in the engine oil when repairing the
engine, all oil passages must be cleaned
carefully, and the oil cooler replaced in order to
prevent further damage occurring later.
The oil level must not be above max. mark on
dipstick - danger of damage to catalytic
converter!
Oil spray jet and pressure relief valve Fig.
1 , Page 17
-6
Viscosity grades and oil specifications:

Repair Manual, Maintenance

Oil system capacity:

Repair Manual, Maintenance

Pa
ge 1 of 35 Lubrication s
ystem com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE06.17.1

17-15


CAUTION!
The hooks and locating pins of the lifting tackle must be secured
with locking pins -arrows in illustration-. - Engage lifting tackle 2024 A in front and rear lifting eyes on engine.
- Pretension engine with spindle of support bar, do not lift.
- Drain engine oil.
- Remove oil return line of exhaust turbocharger from oil pan.

- Disconnect electrical connector -arrow- from oil level sender.
Pa
ge 15 of 35 Lubrication s
ystem com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE06.17.1

17-25

- Immediately attach oil pan and tighten bolts in
described sequence:

Note: - Tighten bolts -1 to 18- diagonally to 5 Nm.
- Tighten bolts securing oil pan to transmission to 45 Nm.
- Tighten bolts M10 -arrows- to 40 Nm.
- Tighten bolts -1 to 18- tighten diagonally to 15 Nm.
Replace seals and gaskets.

When installing the oil pan with the engine removed from the vehicle,
ensure that the oil pan -3- is positioned flush with the intermediate
plate -1- at the flywheel end (i.e. oil pan should protrude dimension "a"
= 0.8 mm from cylinder block with respect to the cylinder block -2-). After installing oil pan assembly, the sealant must dry for approx. 30
minutes. Only then may the engine be filled with oil.
Pa
ge 25 of 35 Lubrication s
ystem com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE06.17.1

17-26


Repair Manual, Suspension, Wheels, Steering, Repair Group 40

Vehicles with automatic transmission:
Repair Manual, 5 Spd. Automatic Transmission 01V, Repair Group 37

All models:
Vehicles with automatic transmission:
Repair Manual, 5 Spd. Automatic Transmission 01V, Repair Group 37 - Support subframe with workshop crane VAG 1202 A.
- Installing subframe:
- Secure ATF lines.- Install lock carrier Page 13
-1 .
- Fill engine with oil and check oil level.
- Check ATF level:
Pa
ge 26 of 35 Lubrication s
ystem com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE06.17.1

17-27

Tightening torques

Component

Nm
Oil pan to cylinder block M7 15

M10 40
Oil pan to transmission 45
Limit stop for torque reaction support on oil
pan
28
Engine mounting to subframe 25
Engine mounting to engine support 25
Transmission support to transmission
support M10 40
Transmission mounting to subframe
M8
25
Oil return pipe to oil pan 10
Oil drain plug 30
Hose clamps for air duct hoses
3.5
Pa
ge 27 of 35 Lubrication s
ystem com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE06.17.1

17-31

Test requirements:

Oil level OK.
Engine oil temperature approx. 80 C.

Oil pressure warning lamp -K3- must come
on when ignition is switched on.
In vehicles with auto check system the "OK"
display must appear (call up symbol).

Testing oil pressure switch

- Disconnect wire from oil pressure switch.

- Remove oil pressure switch and screw in oil pressure tester VAG 1342.
- Thread oil pressure switch -2- intoVAG 1342.
- Connect brown wire -1- of tester to Ground (-).
Pa
ge 31 of 35 Lubrication s
ystem com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE06.17.1

17-32

- Connect voltage tester VAG 1527 B to oil
pressure switch and positive side of battery (+)
using test leads from VAG 1594 A.

Test lamp should not light up.

- If test lamp lights up, install new oil pressure
switch.

- Start engine.

Note:
The switching point of the oil pressure switch can
be reached when the engine is cranked on the
starter motor, so watch the tester and the test
lamp while starting the engine.

Black oil pressure switch:
LED must light up at 1.2 to 1.6 bar.

- If test lamp does not light up, install new oil
pressure switch.
Pa
ge 32 of 35 Lubrication s
ystem com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE06.17.1

17-33

Check oil pressure

- Disconnect wire from oil pressure switch.

If specified values are not attained: - Remove oil pressure switch and screw in oil pressure tester VAG 1342.
- Thread oil pressure switch -2- intoVAG 1342.
-
Start engine (engine oil temperature approx. 80 C).
Oil pressure at idling speed: at least 1.3 bar Oil pressure at 2000 rpm: 3.5 to 4.5 bar
- Pressure relief valve or oil pump faulty, replace oil pump Page 17
-
28
.
Pa
ge 33 of 35 Lubrication s
ystem com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE06.17.1

17-34

Engine oil

The engine is filled with a high quality multigrade
oil at the factory. This oil may be used all year
round, except in extremely cold climates.

Viscosity grades and oil specifications
Viscosity grades and oil specifications:

Repair Manual, Maintenance

Pa
ge 34 of 35 Lubrication s
ystem com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE06.17.1

17-35

Engine oil level, checking


Test requirements:

Engine oil temperature at least 60 C

Vehicle must be level (horizontal)
Wait a few minutes after switching off engine
to allow oil to flow back into oil pan.

- Pull out dipstick, wipe with a clean cloth and
insert again to stop.

- Pull out dipstick again and read oil level.

Markings on oil dipstick:
Note:
The oil level must not be above marking -a- on the dipstick. a - Oilmust not be topped up.
b - Oil may be topped up. The oil level may rise as far as area -a- after
topping up.
c - Oilmustbe topped up. The oil level is sufficient if somewhere in area -
b- (grooved area) after topping up.
Pa
ge 35 of 35 Lubrication s
ystem com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE06.17.1