instrument cluster AUDI A4 1997 B5 / 1.G Brakes Read Mesure Value Block Workshop Manual

01-73

Terminal
Wire connection to component ...
18
Engine Control Module (ECM); MMD signal (Masked Misfire Diagnostic)
for vehicles with Front Wheel Drive (FWD) and ABS/EDL/ASR, the SET signal (Specified Engine Torque) is
also transmitted via this wiring harness.
19
Hydraulic unit; control wire for ABS return flow pump -V39- 20
Engine Control Module (ECM); Engine RPM
for vehicles with Front Wheel Drive (FWD) and ABS/EDL/ASR
25
Hydraulic unit; Left rear ABS outlet valve -N136- 26
Hydraulic unit; Right front ABS outlet valve -N100- 27
Hydraulic unit; right front traction control outlet valve -N167- (primary piston circuit) 28
Ground (GND) terminal 31 (ABS control module -J104-) 29
Ground (GND) terminal 31 (ABS control module -J104-) 31
Instrument cluster; activation of traction control indicator light
for vehicles with Front Wheel Drive (FWD) and ABS/EDL/ASR
32
Instrument cluster; ABS/EDL warning light activation (active) 33
Hydraulic unit; Left front ABS outlet valve -N102- 34
Hydraulic unit; Right rear ABS outlet valve -N135- 35
Left front ABS wheel speed sensor -G47-
for vehicles with All Wheel Drive (AWD) and ABS/EDL
Pa
ge 17 of 79 Read Measurin
g Value Block
(function 08
)
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU02.01.8

01-89

Function test: ABS warning light -K47-
Test step
VAG
1598/20
sockets Test of
Test
requirements
- Additional work
steps Specified value
Corrective action
19

Continuation: - Function of
ABS
warning
light -K47- - Switch on
ignition ABS warning
light -K47- lights
up for two (2)
seconds and
then goes out.
Electrical Wiring Diagrams,
Troubleshooting & Component Locations - If ABS warning light does not come on,
check voltage of electrical system and test
wiring from terminal 32 of ABS control
module -J104- to instrument cluster for
short circuit to Ground (GND).
- The ABS warning lamp does not switch
off after 2 seconds. The red "brake system
malfunction" symbol lights up after 2
seconds. Check wire from terminal 32 of
ABS control module -J104- to instrument
cluster for short circuit to B+ and open
circuit.

Repair Manual, Electrical Equipment,
Repair Group 90; Instrument cluster
- Are both the vehicle voltage and the
wiring from terminal 32 of ABS control
module -J104- to the instrument cluster
OK? Malfunction in instrument cluster. Pa
ge 44 of 79 Read Measurin
g Value Block
(function 08
)
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU02.01.8

01-91

Function test: Red brake warning symbol
Test step
VAG
1598/20
sockets Test of
Test requirements
- Additional work stepsSpecified value
Corrective action
20

Continuation: Function of red
"brake system
malfunction"
symbol - For vehicles with
automatic transmission and
high-line instrument cluster,
depress the brake pedal
and select a driving gear. The ABS/EDL indicator
lamp and the red "brake
system malfunction"
symbol light up. If the
traction control indicator
light is installed and OK, it
also lights up. Repair Manual,
Electrical Equipment, Repair Group 90; Instrument cluster
- Malfunction in
instrument cluster
Pa
ge 46 of 79 Read Measurin
g Value Block
(function 08
)
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU02.01.8

01-93

Function test: Traction control indicator light -K86-. This is only installed if vehicle is equipped with ASR.
Test step
VAG
1598/20
sockets Test of
Test
requirements
- Additional work
steps Specified value
Corrective action
21

Continuation: - Function of
traction
control
indicator light
-K86- - Switch on
ignition Traction control
indicator light -K86-
comes on for two
(2) seconds and
then goes out.
Electrical Wiring Diagrams,
Troubleshooting & Component
Locations - If traction control indicator light does
not light up, check vehicle voltage and
wire from terminal 31 of ABS control
module -J104- to instrument cluster for
short circuit to B+ and open circuit.
- If traction control indicator lamp
remains continuously lit, check wire
from terminal 31 of ABS control
module -J104- to instrument cluster for
short circuit to Ground (GND).

Repair Manual, Electrical
Equipment, Repair Group 90; Instrument cluster
- Are both the vehicle voltage and the
wiring from terminal 31 of ABS control
module -J104- to the instrument
cluster OK? Malfunction in
instrument cluster.
Pa
ge 48 of 79 Read Measurin
g Value Block
(function 08
)
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU02.01.8

01-98
Diagnostic Trouble Code (DTC) table Output on printer of VAG1551
Scan Tool (ST) Possible cause
Corrective action
DTC

00000
No malfunction recognized!
If this display appears, process
is concluded. No DTCs are
stored in DTC memory.
If corresponding warning lamps
light up anyway, check the
following points:
Voltage supply for ABS control module -J104-
below 10.5 volts at a vehicle speed less than 6
km/h. Open circuit in activation wire for ABS warning
light -K47- between ABS control module (w/EDL) -
J104- and instrument cluster combination
processor -J218-. - See section "Overview of
indicator lamp functions"
If no malfunction can be found, and there is still a
problem, there may be a mechanical malfunction (e.g.
solenoid valve sticking). - Expand troubleshooting to
include "Electrical test", function
test page 01
-68
.
Pa
ge 53 of 79 Read Measurin
g Value Block
(function 08
)
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU02.01.8

01-110

Output on printer of
VAG1551 Scan Tool
(ST) Possible cause
Corrective action
DTC
00529
Wheel speed information
missing
No signal

This malfunction only
occurs if vehicle is
equipped with ASR.
Open circuit or short circuit to B+ or
Ground (GND) in wiring between ABS
control module -J104- and Engine
Control Module (ECM).
Electrical Wiring Diagrams, Troubleshooting &
Component Locations - "Read measuring value block", display group 3
page 01
-67
.
- Locate and repair open circuit or short circuit.


Engine Control Module (ECM)
malfunctioning. - If the tachometer in the instrument cluster is
malfunctioning and no malfunctions can be found in
the wiring, the Engine Control Module (ECM) is
malfunctioning and must be replaced.

ABS control module -J104-
malfunctioning - If the tachometer in the instrument cluster
functions properly and no malfunctions can be
found in the wiring, the ABS control module
(w/EDL) -J104- is malfunctioning and must be
replaced.
Pa
ge 69 of 79 Read Measurin
g Value Block
(function 08
)
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU02.01.8

01-111

Output on printer of VAG1551 Scan Tool
(ST) Possible cause
Corrective action
DTC
00532
Voltage supply
Signal too small

Notes:

This malfunction affects the voltage supply
of the control module.
This DTC is only stored, if the malfunction
occurs at a vehicle speed above 6 km/h.
As soon as vehicle voltage is within the
valid voltage range again, the ABS,
ABS/EDL or ASR system is switched back
on and the warning lights turn off.
Open circuit or resistance too high
between voltage supply of terminal 15
and ABS control module -J104-
(terminal 1). Voltage jumps in vehicle system.Battery malfunctioning.
Electrical Wiring Diagrams,
Troubleshooting &
Component Locations
Repair Manual, Electrical
Equipment, Repair Group 90; Instrument cluster
- Carry out "Electrical test",
step 23 page 01-68
.
- Locate and repair open
circuit or contact resistance.
- Check Generator (GEN.)
and Voltage Regulator (VR). - Check battery
Pa
ge 70 of 79 Read Measurin
g Value Block
(function 08
)
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU02.01.8