AUDI A4 1997 B5 / 1.G Front End Workshop Manual

AUDI A4 1997 B5 / 1.G Front End Workshop Manual A4 1997 B5 / 1.G AUDI AUDI https://www.carmanualsonline.info/img/6/885/w960_885-0.png AUDI A4 1997 B5 / 1.G Front End Workshop Manual
Trending: ECU, headlights, cooling, radiator, engine, oil, wheel bolt torque

Page 1 of 19

AUDI A4 1997 B5 / 1.G Front End Workshop Manual 50-1
 
  
Body, front Lock carrier with attachments, removing 
and installing
 
1 - 
Hex bolt (6x) 
45 Nm (33 ft lb)
2 - 
Hex bolt 45 Nm (33 ft lb)
3 - 
Hex bolt (4x) 10 Nm (7 ft lb)
4 - 
Hex bolts (2

Page 2 of 19

AUDI A4 1997 B5 / 1.G Front End Workshop Manual 50-2
 
  
 Repair Manual, Heating & Air Conditioning, 
Repair Group 87
   
Notes: 
 Repair Manual, Suspension, Wheels, Steering, 
Repair Group 48
    7 - 
Lock carrier 
  Removing:
 - Remove bumper  p

Page 3 of 19

AUDI A4 1997 B5 / 1.G Front End Workshop Manual 50-3
 
  
Notes: 
 Repair Manual, Automatic Transmission, Repair 
Group 37     
Do not suspend hydraulic fluid cooler by its 
lines. 
 Hydraulic fluid cooler must not be bent or kinked 
under any circ

Page 4 of 19

AUDI A4 1997 B5 / 1.G Front End Workshop Manual 50-4
 
  
  Installing:
  - Install in reverse order of removal.
 - Adjust headlights.
  Adjusting:
  - Center lock carrier -7- between fenders.
 - If fenders and hood are also being 
replaced, center

Page 5 of 19

AUDI A4 1997 B5 / 1.G Front End Workshop Manual 50-5
 
    
Fig. 1  Disconnecting hydraulic fluid cooler
-  Remove screws for cooling line (for power steering) at engine support 
and transmission. 
    
 Repair Manual, General, Engine, Repair Group

Page 6 of 19

AUDI A4 1997 B5 / 1.G Front End Workshop Manual 50-6
 
    
Fig. 3  Disconnect hose for charge air cooler
-  On vehicles with charge air cooler, loosen bolt on hose clamp (arrow).
- Remove hose.
-  Unscrew air duct to air cleaner at cowl and lift o

Page 7 of 19

AUDI A4 1997 B5 / 1.G Front End Workshop Manual 50-7
 
  
Lock carrier service position
 
Notes: 
 
Do not remove noise insulation. Loosen only 
front quick-release screws   page 50
-18
 . 
 Bumper removed
1 - 
Combination bolt 
45 Nm (33 ft lb)
2

Page 8 of 19

AUDI A4 1997 B5 / 1.G Front End Workshop Manual 50-8
 
  
Note:  
After assembly of the lock carrier, check headlight 
positioning and adjust if necessary.  7 - 
Lock carrier 
For service position
 - Screw special tool 3369 into threaded 
bore -5-

Page 9 of 19

AUDI A4 1997 B5 / 1.G Front End Workshop Manual 50-9
 
    
Fig. 1  Screw in special tool 3369
-  Screw special tool 3369 in at left and right as shown.
-  Pull lock carrier forward until rear hole in lock carrier aligns with front 
threaded hole i

Page 10 of 19

AUDI A4 1997 B5 / 1.G Front End Workshop Manual 50-10
 
  
Front fender (  VIN 8D XA 200 000), 
assembly overview
 
1 - 
Combination bolt 
4.5 Nm (40 in. lb)
2 - 
Threaded rivet Threaded rivet is inserted using VAG1618A
3 - 
Combination bolts (2x)
Page:   1-10 11-20 next >
Trending: oil, wheel, headlights, heating, steering wheel, engine, radiator