engine oil AUDI A4 2000 B5 / 1.G APB Engine Lubrication System Components Owner's Manual
[x] Cancel search | Manufacturer: AUDI, Model Year: 2000, Model line: A4, Model: AUDI A4 2000 B5 / 1.GPages: 74, PDF Size: 1.56 MB
Page 60 of 74
17-55
Front sealing flange and oil pump drive
chain, removing and installing
Removing
- Remove ribbed belt Page 13
-1 .
- Remove toothed belt Page 13
-4 .
- Drain engine oil.
Use a separate container to collect the engine
oil.
Pa
ge 60 of 74 Lubrication s
ystem com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE05.17.1
Page 64 of 74
17-59
Removing and installing chain sprocket on crankshaft Page 17
-62
.
Installing
Install in the opposite order to removing. When installing, note the
following points:
Note:
The front sealing flange must be installed within 5 minutes of applying
silicone sealant D 454 300 A2. - Remove oil pump together with shorter oil supply line.
- Take out oil pump sprocket and remove drive chain from crankshaft.
- Remove any residues of sealant on front of oil pan or engine block, if
necessary.
- Clean sealing surfaces; ensure that they are free of oil and grease.
Pa
ge 64 of 74 Lubrication s
ystem com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE05.17.1
Page 71 of 74
17-65
Oil pressure and oil pressure switch,
checking
Note:
Servicing and checking function of oil pressure
warning lamp and buzzer:
Electrical Wiring Diagrams, Troubleshooting &
Component Locations
Test procedure
- Remove oil pressure switch (F1) and screw oil pressure switch into
tester.
- Screw tester into oil pan in place of oil pressure switch.
- Connect brown wire of tester to ground (GND) (-).
- Using test leads from VAG 1594, connect diode test lamp VAG 1527
between positive battery terminal (+) and oil pressure switch.
- Start engine and gradually increase engine speed.
LED should light up at 1.2...1.6 bar, otherwise replace oil pressure
switch.
- Increase engine speed further.
At 2000 RPM and an oil temperature of 80 C oil pressure should be at
least 2.0 bar.
Pa
ge 71 of 74 Lubrication s
ystem com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE05.17.1
Page 72 of 74
17-66
Engine oil, specifications
A high-quality multigrade oil is put in at the
factory: this can be used all year round, except in
extremely cold climates.
Viscosity grades and oil specifications
Viscosity grades and oil specifications
Repair Manual, Maintenance
Pa
ge 72 of 74 Lubrication s
ystem com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE05.17.1
Page 73 of 74
17-67
Oil level, checking
Test conditions
Oil temperature above 60 C.
Vehicle level.
The vehicle must be standing on level
ground when checking the oil level. Wait for
a few minutes after switching off the engine
to allow the oil to flow back into the oil pan.
Test sequence
- Pull out dipstick, wipe off with a clean cloth and
insert it again as far as it will go.
- Pull out dipstick again and read oil level.
Pa
ge 73 of 74 Lubrication s
ystem com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE05.17.1