engine AUDI A4 2000 B5 / 1.G APB Engine Motronic Multiport Fuel Injection System Servising Service Manual

24-62

- Connect multimeter to terminal 2 of connector
and engine Ground (GND) for voltage
measurement.

- Operate starter briefly.

Specification: approx. battery voltage

Note:
Voltage is supplied to Mass Air Flow (MAF)
sensor from Fuel Pump (FP) relay.
If there is no battery voltage.

- Check wire connection from terminal 2 of
connector to Fuel Pump (FP) relay via fuse for
open circuit and short circuit to Ground (GND),
repair if necessary.

Electrical Wiring Diagrams, Troubleshooting &
Component Locations
Pa
ge 72 of 90 Motronic Multi
port Fuel In
jection
(MFI
) system, servicin
g
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU04.24.1

24-65

Voltage supply for Mass Air Flow (MAF)
sensor, checking (Bosch MAF sensor)

Note:
Voltage is supplied to Mass Air Flow (MAF) sensor from Fuel Pump (FP)
relay.
If there is no battery voltage.
Electrical Wiring Diagrams, Troubleshooting & Component Locations - Disconnect connector from Mass Air Flow (MAF) sensor.
- Connect multimeter to terminal 2 of connector and engine Ground
(GND) for voltage measurement.
- Operate starter briefly.
Specification: approx. battery voltage
- Check wire connection from terminal 2 of connector to Fuel Pump (FP)
relay via fuse for open circuit and short circuit to Ground (GND), repair
if necessary.
Pa
ge 75 of 90 Motronic Multi
port Fuel In
jection
(MFI
) system, servicin
g
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU04.24.1

24-69


Display fields

1 2 3 4
Display Group 002: Intake air mass at idling speed with engine at operating temperature
Display xxx RPM xx.x %
x.x ms
xxx.x g/s
Indicates Engine
speed
(in steps of
40 RPM) Load
Average injection
period Air mass
Work range min.: 750
rpm
max.: 6800
rpm min.: 15
%
max.:
175 % min.: 2.0 ms
max.: 19.0 ms min.: 3.0 g/s
max.: approx: 225g/s
Specification 750 - 850
rpm 15.0 -
25.0 % 2.0 - 4.0 ms1.
3.0 - 4.5 g/s
Note --- ---
If readout does not match
specification, see table for display
field 3 Page 24
-70

If readout does not match
specification, see table for display
field 4 Page 24
-71

If the specification is obtained:

-
Press button.
- Press buttons -0- and -6- to select function "End
Output" and confirm entry with -Q- button.
Pa
ge 79 of 90 Motronic Multi
port Fuel In
jection
(MFI
) system, servicin
g
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU04.24.1

24-70
Reading Display Group 002 Display field
3
Possible cause of malfunction
Corrective action
Less than 2.0
ms
Lower values can only occur when vehicle is on fuel-
shut off (overrun)
More than 4.0
ms Load on engine due to ancillaries- Eliminate load (air conditioner, power
steering, alternator)

Rough idle (engine not running on all cylinders)- Check spark plugs
- Check fuel injectors Page 24
-39


Throttle Valve Control Module -J338 faulty- Check Throttle Valve Control Module
Page 24
-139

Pa
ge 81 of 90 Motronic Multi
port Fuel In
jection
(MFI
) system, servicin
g
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU04.24.1

24-71
Reading Display Group 002 Display field
4
Possible cause of malfunction
Corrective action
Less than 3.0
g/s
Large quantity of un-metered air between intake manifold
and Mass Air Flow (MAF) sensor
Voltage supply to Mass Air Flow (MAF) sensor or wiring to
Engine Control Module (ECM) - Check intake system for leaks (un-
metered air) Page 24
-76

- Check voltage supply and wiring Page 24
-72

More than 4.5
g/s
Load on engine due to accessories- Eliminate load (A/C, power steering,
generator)

Voltage supply to Mass Air Flow (MAF) sensor or wiring to
Engine Control Module (ECM) - Check voltage supply and wiring Page
24
-72

Pa
ge 82 of 90 Motronic Multi
port Fuel In
jection
(MFI
) system, servicin
g
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU04.24.1

24-72

Checking voltage supply to Mass Air Flow
(MAF) sensor

- Disconnect harness connector from air mass
meter.

Note:
The mass air flow sensor receives its voltage supply via the fuel pump
relay.
If the reading does not match the battery voltage:
Electrical Wiring Diagrams, Troubleshooting & Component Locations - Connect hand-held multimeter (voltage measurement range) between
engine Ground (GND) and socket 2 of connector.
- Operate starter briefly.
Specification: approx. battery voltage
- Check for open circuit or short to Ground (GND) in wiring between fuel
pump relay and socket 2 on connector via fuse. Repair if necessary.
Pa
ge 83 of 90 Motronic Multi
port Fuel In
jection
(MFI
) system, servicin
g
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU04.24.1

24-73


Note:
Socket 3 on the connector is the Ground (GND) connection from the
engine control module.
If the specification is not attained: - Connect hand-held multimeter (voltage measurement range) between
sockets 2 and 3 of connector.
- Operate starter briefly.
Specification: approx. battery voltage
- Check wiring Page 24
-74
.

If the specification is not attained: - Connect hand-held multimeter (voltage measurement range) between
sockets 3 and 4 of connector.
- Switch ignition on.
Specification: approx. 5 V
- Check wiring Page 24
-74
.
Pa
ge 84 of 90 Motronic Multi
port Fuel In
jection
(MFI
) system, servicin
g
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU04.24.1

24-74

Checking wiring for mass air flow sensor

Note:
The wiring test includes also testing the signal
wire.

- Connect VAG1598/31 test box to wiring harness
for engine control module. Do not connect to the
engine control module itself Page 24
-20
.

- Check for open circuit and short to B+ or Ground (GND) in the following
wiring connections: Connector for MAF sensor -G70,
socket
VAG1598/31 test box,
socket
3 27
4 53
5 29
Pa
ge 85 of 90 Motronic Multi
port Fuel In
jection
(MFI
) system, servicin
g
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU04.24.1

24-76

Air system for leaks (un-metered air),
checking


Check with engine leak detector spray G 001
800 A1

CAUTION!

Part numbers are for reference only, always
check with your parts department for latest
information.

Notes:

The vacuum in the intake system will cause the
leak detector spray to be drawn in with the
outside air. The leak detector spray reduces the
ignitability of the mixture. This leads to a drop in
engine speed and to a significant increase of
the CO content.
The safety precautions listed on the container
must be adhered to.

- Connect VAG1551 (or VAS 5051) and select
engine electronics control module with the
"Address word" 01. When doing this the engine
must be running at idling speed. (Connect scan
tool and selecting engine electronics control
module Page 01
-9 .)
Pa
ge 87 of 90 Motronic Multi
port Fuel In
jection
(MFI
) system, servicin
g
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU04.24.1

24-77

- Press buttons -0-, -0- and -1- to select "Display
Group 01" and confirm entry by pressing -Q-
button. Read Measuring Value Block 1
1
2
3
4

Indicated on display: (1...4 Display fields)
If the engine speed does not change: - Note engine speed in display field 1.
- Systematically spray parts of intake system with engine leak detection
spray.
-
Press button.- Press buttons -0- and -6- to select function "End Output" and confirm
entry with -Q- button.
Pa
ge 89 of 90 Motronic Multi
port Fuel In
jection
(MFI
) system, servicin
g
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU04.24.1