AUDI A6 1995 C5 / 2.G 01E Transmission Final Drive Ring Gear Adjustment Workshop Manual

AUDI A6 1995 C5 / 2.G 01E Transmission Final Drive Ring Gear Adjustment Workshop Manual A6 1995 C5 / 2.G AUDI AUDI https://www.carmanualsonline.info/img/6/1305/w960_1305-0.png AUDI A6 1995 C5 / 2.G 01E Transmission Final Drive Ring Gear Adjustment Workshop Manual

Page 1 of 15

AUDI A6 1995 C5 / 2.G 01E Transmission Final Drive Ring Gear Adjustment Workshop Manual 39-52
 
     
Ring gear, adjusting 
      (Adjusting differential)  
      Repairs after which the ring gear must be 
adjusted  Page 39
-37
 .   
     
Special tools, testers and auxiliary items

Page 2 of 15

AUDI A6 1995 C5 / 2.G 01E Transmission Final Drive Ring Gear Adjustment Workshop Manual 39-53
      
Thrust pad 3062
     Thrust plate 30-205
     Mandrel 30-505
     Torque gauge 0-600 Ncm
     Dial gauge 
     Dial gauge extension
Pa
ge 2 of 15 Rin
g gear, ad
justin
g
11/19/2002 htt
p:

Page 3 of 15

AUDI A6 1995 C5 / 2.G 01E Transmission Final Drive Ring Gear Adjustment Workshop Manual 39-54
      
Determining total shim thickness "S
total
" for 
shims "S1" + "S2"   
      (Setting preload of tapered roller bearing for 
differential)   
     
Drive pinion removed 
     
-  Remove se

Page 4 of 15

AUDI A6 1995 C5 / 2.G 01E Transmission Final Drive Ring Gear Adjustment Workshop Manual 39-55
 
    
-  Press outer race for tapered roller bearing without shim "S1" into cover 
for differential. 
-  Insert differential without drive wheel for speedometer sender -G22 into 
transmission h

Page 5 of 15

AUDI A6 1995 C5 / 2.G 01E Transmission Final Drive Ring Gear Adjustment Workshop Manual 39-56
      
Note:  
    
Secure special tools VW 521/4 and VW 521/8 on right of differential 
(transmission side) to lift differential. If the measurement has to be repeated, the differential must ag

Page 6 of 15

AUDI A6 1995 C5 / 2.G 01E Transmission Final Drive Ring Gear Adjustment Workshop Manual 39-57
      
Determining thickness of shim "S1*"  
     
Note:  
     
The preliminary adjustment shim "S1*" will be 
replaced with the final shim "S1" after 
determining the backlash. 
     The total

Page 7 of 15

AUDI A6 1995 C5 / 2.G 01E Transmission Final Drive Ring Gear Adjustment Workshop Manual 39-58
      
Measuring friction torque (check)  
     
Note:  
     
Differential tapered roller bearings are low 
friction bearings. Therefore the friction torque 
only has a limited use as a check.

Page 8 of 15

AUDI A6 1995 C5 / 2.G 01E Transmission Final Drive Ring Gear Adjustment Workshop Manual If the final drive set (drive pinion and ring gear) is being adjusted, perform 
the adjustment of the drive pinion now and check the adjustment   Page 39
-39
 . 
Pa
ge 8 of 15 Rin
g gear, ad
justin
g

Page 9 of 15

AUDI A6 1995 C5 / 2.G 01E Transmission Final Drive Ring Gear Adjustment Workshop Manual 39-59
      
Measuring backlash  
      (Position of ring gear in transmission housing)  
     
Drive pinion with shims "S3" and "S4" 
installed 
     
- Install differential.
     
-  Turn differenti

Page 10 of 15

AUDI A6 1995 C5 / 2.G 01E Transmission Final Drive Ring Gear Adjustment Workshop Manual 39-60
      
  -  Read off backlash and note value.
     
 - 
Turn ring gear through 90  and repeat 
measurements a further 3 times.      
Note:  
     If the individual measurements differ by more 
t
Page:   1-10 11-20 next >