spare wheel AUDI A7 2015 User Guide

M N <( (.J
'SI: ,...., \!) ..,.,
,...., ..,., ,....,
Changing a wheel
Before changing a wheel
Observe the following precautions for your
own and your passenger's safety when chang­
ing a wheel .
.,. After you experience a tire fa ilure, pull the
car well away from moving traffic and try to
reach
level gro und before you stop¢.&_ .
.. All passengers should
leav e the car and
move to a safe location (fo r instan ce, be hind
the guardra il) ¢.&_ .
.. Engage the
parkin g brake to prevent your
vehicle from ro lling unintentionally ¢.&_ .
.. Move
selecto r le ver to p osition P ¢ .&_ .
1> Ifyou are towing a trai ler, unh itch the tra iler
from your vehicle .
.,. Take the
jack and the spare tire out of the
luggage compartment
¢ page 273,
¢ page 274 .
.8, WARNING
You or your passengers cou ld be injured
while changing a whee l if yo u do not fol­
low t hese safety precautions:
- If you have a flat t ire, move a safe dis ­
tance off the road. Tur n off the eng ine,
turn the emergency f lashers on and use
other warning dev ices to alert other mo­
torists.
- Make sure that passengers wait in a safe
place away from the ve hicle and well
away from the road and traff ic.
- To help p revent the vehicle from moving
s u dden ly and possibly slipping off the
jack, always fully set the parking brake
and block the wheel diagonally opposite
the wheel being changed. Whe n one
front wheel is lifted off the ground, plac­ ing the A utomat ic Transm iss ion in P
(Pa rk) will
not p revent the vehicle from
moving.
- Before you change a wheel, be su re the
ground is level and fi rm. If ne cessa ry,
use a st urdy board under the jack.
-
What do I do now? 275
- Always store the vehicle tool kit, the jack
and the replaced tire in the luggage com­ partment
c::>page 134.
(D Tips
Before changing the whee l, you must acti­
vate the jacking mode, so that the auto­ matic controls for the Adaptive Air Sus­
pension* do not make it more d iff icult to
lift the vehicle with the jack
c::> page 2 77 .
Changing a wheel
When you change a wheel , follow these­
quence described below s tep-by-s tep and in
exactly that order .
l. Activate the vehicle jack mode*
¢page 277 .
2. Remove the decorativ e wheel co ver* . For
more details see also
c::> page 2 76, Deco­
rative wheel covers
or c::> page 2 76,
Wheels with wheel bolt caps .
3. Loosen the wh eel bolt s ¢page 277.
4 . Loca te the p roper moun ting poin t for the
jack and align the jack be low that point
¢ page 277 .
5.
R ais e the car with the jack¢ page 2 77.
6. Remove the
wheel with the flat tire and
then install
the spar e c::>page 279.
7. Tighten all whee l bolts lightly .
8.
Lo wer the vehicle with the jack .
9 . Use the wheel bolt w rench and
firmly
t ighten al l wheel bolts ¢ page 2 77.
10 . Replace the decorative
wh eel c ov er* .
11. Deactivate the vehicle jack mode* in the
MM I:
ICARI f u nction button > (Car )* sy s­
tems
contro l button > S erv ici ng & che cks
> A ir s usp .: jac k mode > Off .
The vehicle jack mode * switches off automati­
ca lly at speeds above 6 mph (10 km/h) .
.8, WARNING
-Always read and fo llow all WARNINGS and
i nformat ion
c::> A in Raising the vehicle on
page 278
and c::> poge 280.
•
•

276 What do I do n ow ?
After changing a wheel
A wheel change is no t complete without the
doing the following .
.. Always store the vehicle tool kit, the jack*
and the replaced tire in the luggage com­
partment ¢
page 134.
.. Check the tire pre ssur e on the spare wheel
immediately after mount ing it .
.,. As soon as possible, have the
tightening
torqu es
on all wheel bol ts checked with a
torq ue wrench. The correct tightening tor ­
que is 90 ft lb (120 Nm) .
.. Have the flat tire
replaced as soon as possi­
ble.
@ Tips
- If you notice t hat the wheel bolts are
corroded and difficult to t urn while
changing a t ire, they should be replaced
before you check the tighten ing torque.
- Drive at reduced speed unt il you have the
tightening torques checked .
- After changing a wheel, the tire pressure
i n a ll four tires must be checked/correct­
ed and the tire pressure mon itor ing indi­
cator must be stored in the MMI
¢ page 272 .
Decorative wheel covers
Applies to vehicles: with decorative wheel covers
T he decora tive wheel covers must be removed
first to access the wheel bolts .
Fig. 210 Cha nging a w hee l: Remov ing t he w heel cove r
Removing
.,. Inse rt the hook (prov ided with the veh icle
tool kit) in t he hole in the wheel hub cove r. ..
Pull off the
de cora tive wheel co ver
¢ fig . 210.
Wheels with wheel bolt caps
Applies to veh icles: w it h w heel bolts with caps
The caps must be removed first from the
wheel bolts before the bolts can be un­
screwed.
Fi g. 211 Cha ng ing a whee l: re m oving t he w hee l b o lt
caps
Removing
.. Push the plastic clip (provided with t he veh i­
cle tool k it) over the wheel bo lt cap until the
inner retainers on the clip align w ith the
edge of the cover.
.,. Remove the cap with the
plastic clip (vehicle
tool kit)
i=> fig . 211 .
Refitting
.. Place the caps over the whee l bolts and
push them back on.
The caps are to protect and keep the wheel bolts clean .

M N <( I.J - "' rl
"' rl
Taking the wheel off/installing the spare
Follow these instructions step-by-step for
changing the wheel.
Fig. 216 Changing a wheel: using the screwdriver han­
dle (with the blade removed} to turn the bo lts
F ig . 2 17 Changing a wheel: alignment pin ins ide the
top hole
After you have loosened a ll wheel bolts and
ra ised the veh icle off the ground, remove and
replace the wheel as follows:
R emoving the wheel
.. Use the hex agon al so ck et in th e screw driv­
e r handle
to comp letely remove the top­
most wheel bo lt and set it aside on a
clean
s u rface ¢fig. 216.
.. Screw the threaded end of the alignm ent
pin from the tool k it hand -tight into the
empty bolt hole
¢fig. 217.
.. Then remove the other wheel bo lts as de­
scribed above .
.. Take off the wheel leav ing the alignment pin
in the bolt hole
¢ (D.
Putting on the spar e wheel
.. Lift the spare wheel and carefully slide it
over the alignment pin to guide it in place
¢(D.
What do I d o now ? 2 79
.. Use the hexagonal socket in the screwdriver
handle to screw in and tighten all wheel
bolts
slightly.
.. Remove the alignment pin and insert and
tighten the remaining wheel bolt slightly like the rest.
.. Turn the jack handle counter-clockwise to
lower the veh icle until the jack is fully re­
leased .
.. Use the wheel bo lt wrench to tighten all
wheel bo lts f irm ly
¢page 277. Tighten
them
crosswise, from one bolt to the (ap­
proximately) opposite one, to keep the
wheel centered.
(D Note
When removing or installing the whee l,
the rim could hit the brake rotor and dam­
age the rotor. Work carefu lly and have a
second person help you.
@ Tips
Neve r use the hexagonal socket in the han ­
dle of the screwdriver to loosen or tighten
the w heel bo lts.
- Pull the reversible blade from the screw­
dr iver before you use the hexagonal
socket in the hand le to turn the wheel
bolts.
- When mount ing tires w ith
unidi rectional
tread design
make sure the tread pat­
tern is po inted the right way
~page 280.
-The wheel bo lts shou ld be clean and easy
to turn. Check for dirt and corrosion on
the mating surfaces of both the wheel
and the hub. Remove all d irt from these
surfaces before remounting the whee l.

28 0 What do I do no w?
Tires with unidirectional tread design
Tires with unidirectional tread design must be
mounted with their tread pattern pointed in the right direction .
Using a sp are t ire wi th a tread pattern
int ended fo r use in a specific dir ect ion
When us ing a spare tire w ith a tread patte rn
intended for use in a specific direction, please
note the following:
- The direction of rotation is marked by an ar­
row on the side of the tire.
- If the spare t ire has to be installed in the in­
correct direction, use the spare tire only
temporarily since the t ire will not be able to
achieve its optimum performance character­
ist ics with rega rd to aquaplaning, noise and
wea r.
- We recommend that you pay particular at­
tent ion to this fact du ring wet weather and
that you adjust your speed to matc h road
conditions.
- Replace the flat tire w ith a new one and
have it installed on your vehicle as soon as
possible to restore the handling advantages
of a unidirectiona l tire .
Notes on wheel changing
Please read the information c> page 260 , New
t ires and replacing tires and wheels
if you are
going to use a spare tire which is different
from the tires on your vehicle .
After you change a tire :
-Che ck the tire p re ssure on the sp are imme ­
di ately afte r in st a llat ion.
- Ha ve th e wh eel b olt tightenin g torque
che ck e d w ith a torque wrench as soon a s
possible b y you r autho rized Aud i de aler o r
a qu alified ser vice station .
- With ste el and alloy wheel rims , the wheel
bolts are cor rectl y tightened at a torque of
90 ft lb (1 20 Nm ).
- If yo u notice that the wheel bolt s are cor­
r oded a nd d iffi cult to tu rn while changi ng
a t ire, the y should be replaced before you
check the t ightening torq ue. -
Re pl ac e the flat ti re with a new one and
h av e it in st a lled on you r vehicle as soon as
po ssible. Remount th e wheel cov er.
Un til then , driv e with ex tra c are a nd at re­
duc ed sp ee ds.
A WARNING
-
- If you are going to equ ip your vehicle
with tires or rims which differ from those
which were factory installed, then be
sure to read the information
9 page 260,
New tires and replacing tires and
wheels .
-Always make sure the damaged wheel or
even a flat tire and the jack and tool kit
are properly secured in the luggage com­
pa rtment and are not loose in the pas­
senger compartment.
- I n an accident or sudden maneuver they
could fly forwa rd, injuring anyone in the
veh icle.
- Always sto re damaged wheel, jack and
too ls securely in the luggage compart­
ment. Otherwise, in an accident or su d­
den maneuve r they could f ly forward,
causing injury to passengers in the ve hi­
cle.

M N <( I.J ""'. rl I.O
"' rl
"' rl
Technical data
Vehicle identification
F ig. 231 Veh ide Identificat ion Number (VlN) plate: lo ·
c ation on d river 's s ide das h pane l
XXXXX XX · X -XXXX XXX
~ fAllftlli. -llllll · NR. ~ W!ru -llllll -NO.
xx
XXXX XXXX XX X XXXXXXXX
XXX XXX
IYP /TYPE
XX XXXXXXX XX X X XX
XXX KW XXX
®i ~W.::·f :l~~ XXXX XXX XXX
©+ ::rw= xxxx I xxxx XXX I xx
M. · AUSSt I IJ'IIDIIS
~--
EOA 7D 5 4UB 6XM SSG SRW
2E H JOZ 1LB lA S 1BA
3FC SMU 7X l
FD A 9G3 OG7 OYH OJF
TL6 3 KA 8EH UlA X98 027
lXW 803 908 824 D2D
7T6 CV7 7KO 4X3 2K2
3L4 4KC 3YO 413 502
1S A 7GB 01A 4GO
XX. X XX X XX X XXXX
Fig. 232
The vehicle identification label - inside the
luggage co mpartment
Vehicle Identification Number (VlN)
The Veh icle Identification Number is located
in different p laces :
- under the w indshield on the driver's side
¢fig. 231.
- in the MMI: Select: Function button ICAR ! >
(Car)* systems> Servicing & checks > VIN
number.
-on the vehicle identification label.
Techni cal data 291
Vehicle identification label
The vehicle identification label is located in
the luggage compartment in the spare wheel
well.
T he label¢
fig. 232 shows the following vehi­
cle data :
(D Vehicle Identificat ion Number (VIN)
@ Vehicle type, engine output, transmission
® Engine and transmission code
© Paint number and interior
® Optional equipment numbers
The information of the veh icle identification
label can also be found in your Warranty
&
Maintenance booklet .
Safety compliance sticker
The safety compliance sticker is your assur­
ance that your new veh icle complies with all
applicable Federal Motor Vehicle Safety
Standards which were in effect at the time the
vehicle was manufactured . You can find this
sticker on the door jamb on the driver's side. It shows the month and year of production
and the vehicle ident ification number of your
vehicle (perforation) as well as the Gross Vehi­
cle Weight Rating (GVWR) and the Gross Axle
Weight Rating (GAWR) .
High voltage warning label
The high voltage warning label is located in
the engine compartment next to the engine hood release. The spark ignition system com­
plies with the Canadian standard ICES-002 .
Weights
Gross Vehicle Weight Rating
The Gross Vehicle Weight Rating (GVWR), and
the Gross Axle Weight Rating (GAWR) for
front and rear are listed on a sticker on the
door jamb on the driver's s ide.
The Gross Vehicle Weight Rating includes the
weight of the basic vehicle plus full fuel tank,
oil and coolant, plus maximum load, which in ­
cludes passenger we ight (150 lbs/68 kg per
II>--

M N <( (.J
'SI: ,...., \!) 1.1'1 ,...., 1.1'1 ,....,
Certification .... ... .... ... .. .. .. ... 297
Changing a wheel ................... 275
Changing engine o il ........ .. .. .. .. . 230
Chec king
E ng ine coolant leve l .... ... .. .. .. .. . 23 1
Tire pressure . .. .. ..... ... .. .. .. ... 252
Ch ild restra ints
D anger of using c hild restra ints in the
fro nt sea t . . . . . . . . . . . . . . . . . . . . . . . . 149
Where can I get add it ional information
about child restra ints and their use? .. 19 1
Ch ild restra int system anchors . ....... 187
Ch ild safety .. ............. .... .. ... 173
Convertible locking retractor . . . . . . . . . 184
Important safety instructions for us ing
ch ild safety seats ...... ..... .. .. .. . 177
I mportant th ings to know when dr iv ing
wi th ch ild ren ............ .... .. ... 173
Tether anchors ........... .. .. .. ... 190
Tether straps ... ...... ... .. .. .. .. . 190
Ch ild safety lock
Rear doors ........................ 40
Ch ild safety seats .......... .... .. ... 179
Booster seats ............ .... .. .. . 182
Convertible c hild seats ....... ... .. . 180
Convertible locking retracto r .. ....... 184
H ow do I properly install a child safety
seat in my vehicle? ........ .. .. .. .. . 177
I nfant sea ts ............. .... .. .. . 179
I ns tall ing .. ............. .. .. .. .. . 184
I ns tal ling a child restraint using the
L A TCH system .. .. ..... ... .. .. .. ... 189
LATCH system . . . . . . . . . . . . . . . . . . . . . 189
Lower anchorages ........ .. .. .. .. . 188
Mounting and releasing the anchorage
hook .. .. .. .. ........ ..... ... ... . 189
Safety instructions ................. 177
Unused safety belts on the rea r seat .. 179
Cigarette lighter . . . . . . . . . . . . . . . . . . . . . 59
Cle aning .. .. ............. .... .. .. . 212
Climate control Air vents ... ... .. .. ... ... .. .. .. .. .. 71
Climate controls . . . . . . . . . . . . . . . . . . . . . 69
Climate con trol sy stem
Supp lementary hea ter .. ... .. .. .... .. 74
Climate control (four-zone) Operation . . . . . . . . . . . . . . . . . . . . . . . . . 72
Inde x 301
Climate control (three -zone)
Operation . . . . . . . . . . . . . . . . . . . . . . . . . 70
Clock .............................. 27
Closing Rear lid ........................... 37
Slid ing/tilting sunroof ......... .... .. 41
Cold tire inflation p ress ure ..... ... .. .. 247
Coming home . .. .. ................. . 46
Compact spare tire .................. 274
Compartments .. .... . ... ...... ... .. . 60
Compliance ....... .. ............... 297
Consumer Information . . . . . . . . . . 136, 294
Consu mption (f uel) ............. .. .. . 25
Contacting NH TSA ................. . 136
Controls Cleaning . ... .. .. .. .. .. ...... ... .. 214
Convenie nce key . ...... ............. . 35
Star ting the engine . ........... .... . 76
S topping the eng ine (START ENG INE
STOP b utton) . . . . . . . . . . . . . . . . . . . . . . 77
Switching the ignition on .... ... .. .. . 76
U nlocking and locking vehicle ......... 35
Convertib le child sa fe ty se ats ......... 180
Convertib le locking retractor
Activati ng . . . . . . . . . . . . . . . . . . . . . . . . 186
Deact ivating . .. .. .. ..... .......... 186
U sing to secu re a child safety seat 1B4, 186
Coolant
refer to Engine coolant ............ . 231
Cooling mode (automatic climate control) 72
Cooling mode (climate cont rol) . . . . . . . . . 70
Cruise contro l
Changi ng speed .. .. . .. .. ... ..... .. . 84
P resett ing your speed ............... 85
Switching off ...................... 85
Switch ing on . .. .. .... ........... .. . 84
Wa rning/ind icator lights ........ .. .. . 23
(upholder .. .. .. .. ... ... ...... ..... . 60
C ur ve lig ht . ... .... ... .. .. ..... ... .. 102
Cylinder managem ent
refer to Cyli nder on dema nd System .. . 25
Cyl inder on demand System
25
D
Data recorder ... ...... ............. 194
Date d isp lay .. .. .. .. ............... . 27
•
•