light AUDI S3 2015 Owners Manual

Tires and wheels 24 7
It is important to check the tire sure for the spare wheel
pressure when the tires are
¢page 268.
cold.
When should I adjust the
-Read the required tire pres-tire pressures?
'
sure from the tire pressure la-
Adjust the tire pressure to the •
•
bel. The tire pressure label is load you are carrying. After
located on the driver's side B- changing a wheel
or replacing
pillar. wheels you have to adjust the
-Turn the valve stem cap coun- tire pressures on all wheels. In
ter-clockwise to remove it addition, you must then store
from the tire valve. the new tire pressures in the
-Place the air pressure gauge tire pressure monitoring sys-
on the valve. tern
¢ page 264.
-The tire pressures should only
A WARNING
be checked and adjusted when
Incorrect tire pressures and/
the tires are cold . The slightly
or underinflation can lead
raised pressures of warm tires
sudden tire failure, loss of
must not be reduced.
control, collision, serious per-
-Adjust the tire pressure to the
sonal injury or even death.
load you are carrying.
-When the warning symbol
-Reinstall the valve stem cap
RI] appears in the instru-
on the valve.
ment cluster, stop and in-
When should I check the tire spect the tires.
pressure? -Incorrect tire pressure and/
The correct tire pressure is es- or underinflation can cause
pecially important at high increased tire wear and can
speeds. The pressure should affect the handling of the
therefore be checked at least vehicle and stopping ability.
once a month and always be- -Incorrect tire pressures
fore start ing a journey. Do not
and/or underinflation can
' • M N
forget to check the tire pres-0 > co .... \!) 1.1'1
M 1.1'1 ....

M N
0 > co ,...., \!) 1.1"1
M 1.1"1 ,....,
reached the level to trigger illumination of the
TPMS low tire pressure telltale.
Your veh icle has also been equ ipped with a
TPMS malfunction indicato r to indica te when
the system is not operating properly . The
TPMS malfunction indicator is combined with
the low tire pressure tellta le . When the sys­
tem detects a malfunct ion, the telltale will
flash for approximately one minute and then
remain cont inuous ly illuminated. This se ­
quence will continue upon subsequent vehicle
start-ups as long as the ma lfunction ex ists .
When the malfunct ion indicator is illuminat­
ed, the system may not be able to detect or
sig nal low t ire pressure as intended . TPMS
malfunct ions may occur for a variety of rea­
sons, including the installa tio n of replace­
ment or a lternate tires or whee ls on the veh i­
cle that prevent the TPMS from funct ion ing
properly. Always check the TPMS malfunction
tellta le after replacing one or more tires or
wheels on your veh icle to ensure that the re­
placement or alternate tires and wheels allow
the
TPMS to continue to function properly.
If the Tire Pressure Monitoring System
indicator appears
Applies to vehicles: with tire pressure monito ring system
The tire pressure indicator in the instrument
cluster informs you if the tire pressure is too
low or if there is a system malfunction .
Fig . 173 In strum ent clus te r: indica tor l igh t w ith mes ­
sage
Using the ABS sensors, the tire pressure moni­
toring system compares the t ire tread circum­
ference and vibration characteristics of the in­
d iv idual tires . If the pressure changes in one
Tire s an d wheel s 265
or more tires, this is indicated in the instru ­
ment cluster disp lay with an indicator light
ti] and a message c:::> fig . 17 3. If only one tire
is affected, the locat ion of that tire will be in­
dicated. The message turns off after a few mi­
nutes . You can d isplay the message aga in
c:::> page 2 9 .
The tire pressures must be stored in the menu
display again each time the pressures change
(sw itching between partial and full load pres ­
sure) or after chang ing or replacing a t ire on
your vehicle
c:::> page 266 . The t ire press ure
monitori ng system only monito rs the tire
pressure yo u have stored . Yo u can find the rec ­
ommended t ire press ures for your vehicle on
the labe l on the driver 's doo r pillar
c:::> page240 .
Tire t read circumference and vib rat ion charac­
teristics can change and cause a tire pressu re
warning if :
- I f the tire pressure in one or mo re tires is
t oo low,
- the t ire has structural damage,
-The tire was replaced or the t ire p ressure
changed and it was not stored again
c:::> page 266 .
- The spare tire is installed .
Indicator light s
ti]-Loss of pressure in at least one tire c:::> &.
Check the tires and replace or repair if neces­
sary. Check/correct the pressures of all four
tires . Then store the t ire pressures in the MMI
c:::> page 266 .
DI (T ire Pressure Monitoring System) T ir e
press ure: S ystem malfunct ion!. If Ill ap­
pears afte r switching the ignition on or while
driv ing and the
ti] indicator l ight in the in­
str ume nt cluster b links for app rox imately one
minute and then stays on , the re is system
malfunction. Try to s to re the co rrec t ti re pres­
s u res
c:::> page 266. If the indicator ligh t does
turn off or tu rns on again after a short period
of time, drive to yo ur authorized Aud i dea ler
or qualified repa ir facility immed iate ly to have
the malfunction corrected. .,..
•
•
•

266 Tire s and wheels
& WARNING
-If the tire pressure warning light ti] in
the instrument cluster turns on, the
pressure in one or more tires is too low.
Reduce the vehicle speed immediately
and avoid any hard steering or braking
maneuvers . Stop as soon as possible,
check the t ire and inflate the tire to the
correct pressure, which is specified on
the tire pressu re label on the veh icle
¢ page 240. Driving with a t ire with low
pressure causes the tire to overheat and
can result in failure of the tire . Low pres ­
sure can a lso have a negative effect on
the driving and braking behavior of the
vehicle.
- The driver is responsible for maintaining
the correct tire pressures. You must
check the t ire pressures regularly.
- Under certain conditions (such as a spor­
ty driving style, winter conditions or un­
paved roads), the pressure monitor ind i­
cator may be delayed .
- Ask your author ized dealer if run-flat
t ires may be used on your vehicle.
- The tire pressure monitoring system can
also stop work ing when there is an ESC
malfunction.
- Using snow chains may result in a system
malfunction.
- The tires with the identification "AO" or
"RO" ¢ page 254 have been matched
with your Audi tire pressure monitoring
system. We recommend that you use
these tires.
- The tire pressure monitoring system can
only mon itor the t ire pressure of the
driving tires . Check the tire pressure of
the spare wheel in the luggage compart­ ment so that if necessary it is ready for
us e.
-
Storing tire pressures
Applies to vehicles: wit h tire press ure mo nitor ing system
A change in tire pressure or a change in tires
must be stored in the system.
The tire pressure is stored in the MMI.
.. Make sure before storing that the tire pres ­
sures of a ll four tires meet the specified va l­
ues and are adapted to the load. Otherwise
the system could malfunction
¢ page 240.
.. Switch on the ignition.
.. Select: the
I MENU I button >Car > Systems*
control button > Service & control > Tire
pressure monitor > Store tire pre ssure >
Yes, store now.
(D Tips
Do not store the tire pressures if snow
chains are installed. Otherwise the system
could malfunction.

....,
N
0 > co
rl I.O
"' ....,
"' rl
-Support the vehicle securely with ap­
propriate stands if work is to be per­
formed underneath the vehicle;
otherw ise, there is a potential risk for
injury .
- To help prevent injury to yourself and
your passenge rs:
- Do not raise the vehicle until yo u are
sure the jack is secu rely engaged .
- Passenge rs must no t remai n in the ve­
h icle when it is jacked up .
- Ma ke sure that passengers wait in a
safe place away from the vehicle and
well away from the road and traff ic.
- Make sure ja ck position is correct, ad­
jus t as necessary and then conti nue to
raise the jack .
- Changes i n tem pera ture or load can af­
fect the height of the vehi cle.
(D Note
Do not lift the vehi cle by the s ill. Pos ition
the vehicle jac k only at the designated lift­
ing points o n the sill. Othe rwise, your vehi­
cle will be damaged .
Taking the wheel off/installing the spare
Follow these instructions step-by-step for
changing the wheel.
F ig . 1 84 Chan gin g a w hee l: us ing t he sc rew driver han ­
dl e (w it h t he bla de removed) to t urn th e bolts
What do I d o now ? 273
Fig . 1 8 5 Changi ng a wheel : al ig nme nt p in in sid e th e
t op hole
After yo u have loosened all wheel bo lts and
raised the vehicle
off the ground, remove and
replace the wheel as follows :
Removing the wheel
.,. Use the he xag onal so cket in the scre wdriv ­
er handle
to comple tely remove the top­
most whee l bolt and set it aside on a
clean
surface ¢ fig. 184.
.,. Screw the threaded end of the alignment
pin from the tool kit hand- tight into the
empty bolt hole
Q fig . 185.
.,. Then remove the other wheel bolts as de­
scribed above .
.,. Take
off the whee l leaving the alignment pin
in the bo lt ho le
¢ (D .
Putting on the comp act spare wheel
.,. Lift the spare wheel and carefully slide it
over the alignment p in to g uide it in place
¢ (D .
.,. Use the hexagona l socket in the screwd river
h a ndle to screw in a nd tig hten all whee l
bolts
slightly .
.,. Remove the alignment pin and insert and
tighten the remaining whee l bolt slightly
like the rest .
.,. Turn the jack hand le counter-clockwise to
lower the veh icle until the jack is fully re­
leased .
.,. Use the wheel bo lt wrench to tighten all
wheel bo lts firm ly
i=;, page 271. Tighten
them
c rosswise, from one bolt to the (ap­
proximately) opposite one, to keep the
wheel cente red.

....,
N
0 > co
rl I.O
"' ....,
"' rl
Interior fuse assignment
Fig. 188 Vehicle inter ior: fuse assignment
No . Equ ipment
Fl Engine components
F2 Seat adjustment
F 3 Hydraulic pump
cover (Cab-
riolet)
F4 MM controls, MMI-compo-
nents
FS Gateway
F 6 Anti-theft alarm system
Climate/heating control,
se-
lector lever (automatic
F7 transmission), park ing heat-
e r, rear window heater relay
coil
Diagnosis, electrical parking
F 8 brake
switch, light switch,
rain/light sensor, interior
light ing
F9 Steering
column switch
module
Fl0 Disp lay
Fll Reversible driver's
side safe-
ty belt tensioners
Fl2 MMI a rea
No .
Fl 3
Fl4
Fl5
Fl6
Fl7
Fl8
Fl9
F20
F23
F24
F25
Ampere
30 F26
10 F27
40 F28
F29
7.5
F31
s F32
5 F33
10 F34
10 F35
1 F36
5
25 F37
15/20
Fu se s and bulb s 2 77
Equipment Ampere
Adaptive dampers control
20
module
Climate control system 30
blower
Electronic steering column
10
lock
MM I area 7.5
Instrument cluster 5
Rearview camera 7.5
Conv ince key system control
7.5
module, tank system
Tank system 7.5
Ex terior lighting, heated
40
washer fluid nozzles
Panorama sunroof/ power
top control modu le, power 20/30
top latch (Cabriolet)
Door/dr iver's side doors (for
30
example power windows)
Seat heati ng 30
Sound-amplifier 30
Power top con trol module,
5
electron ics (Cabriolet)
Interior lights 7.5
Ex terior lighting
40
Driver assistance systems 7.5
Airbag 5
Button illumination, coils
for upper cab in heat ing relay
(Cabriolet) and socket relay,
7.5
interior sound, back-up ligh t
switch, temperature sensor, o il level sensor
Diagnosis, headlight range
control system, air quality
10
senso r, a utomat ic dimming
rearview mir ror
Right corner ing light/ right
15
LED-headlight
Left corner ing light/ left
15
LED -head light

2 78 Fuses and bulbs
No . Equipment Ampere
Door/front passenger's side
F39 doors (for example, power 30
windows)
F40 Sockets 20
F41 Reversible front passenger·s
25
side safety belt tensioners
F42 Central locking components,
40
windshield washer system
F43 Headlights , light ing 30
F44 all wheel drive
15
F49 Starter, clutch sensor, head-
s light
relay coil
FS3 Rear window defogger
30
The power seats* are protected via
circuit
breakers
that automatically switch on after a
few seconds after the overload has been re­
duced.
@ Tips
Note that the following table was accurate
at the time of print ing and is subject to
change.
Left engine compartment fuse
assignment
Fig. 189 Engine compartment : fuse assignment
No.
Fl
F2
F3
F4
F5
F6
F7
F8
F9
FlO
Fll
Fl2
Fl3
Fl5 Fl6
Fl7
Fl8 Fl9
F20 F22
F23
F24
F3 1
F32
Equipment Ampere
ESC control modu le 40
ESC cont rol module 40
Engine control module (gas-
15/30
oline/diesel)
Engine cooling, engine com-
ponents, auxiliary heater 5/10
coil relay (1+2), secondary
air injection pump relay
Engine components, tank 7.5/10/
system 15
Brake light sensor
5
Engine components, water 7.5/10/
pumps 15
Oxygen sensor 10/15
Engine components, ex-
haust door, glow t ime con-
5/10/20
trol module, SU LEV valve
Fuel injectors, fuel control
15/20
module
Auxiliary heater heating ele-
40
ment2
Auxi lia ry heater heating ele-
40
ment 3
Automatic transmission con- 15/30
trol module
Horn 15
Ignit ion coil 5/20
ESC contro l module, engine
7.5
control module
T ermina l 30 (reference volt-
5
age)
Windshield wipers 30
Horn 10
Terminal SO diagnosis 5
Starter 30
Auxiliary heater heat ing ele-
40
ment 1
Vacuum pump 15
LED headlights 5

M N
0 > co ,...., \!) ..,.,
M ..,., ,....,
@ Tips
Note that the following table was accurate
at the time of pr int ing and is subject to
change.
Bulbs
Replacing light bulbs
For your safety, we recommend that you have
your authorized Audi dealer replace burned out bulbs for you.
It is becoming increas ingly more and more
d ifficult to replace veh icle light bulbs since in
many cases, other parts of the car must first
be removed before you a re able to get to the
bu lb. This app lies especia lly to the light bu lbs
in the front of your car which you can on ly
reach through the engine compartment .
Sheet metal and bulb ho lders can have sha rp
edges that can cause ser ious c uts, and parts
must be co rrectly taken apart and then prop ­
erly put back together to help prevent break­
age of parts and long term damage from wa­
ter that can enter hous ings that have not been
properly resealed.
F or your safety, we recommend that you have
your authorized Audi dealer rep lace any bulbs
for you, since your dealer has the proper tools,
the correct bulbs and the expertise.
G as discha rge l amps (Xenon light s):
Due to the high elect rical voltage, have the
bu lbs rep laced by a qualified technician.
Headlights wi th Xenon light can be identified
by the high voltage sticker .
L ED headlights* requ ire no ma intenance .
Pl ease contact yo ur a uthorized Aud i dealer if a
bu lb needs to be replaced.
A WARNING
Contact with high-voltage components of
the electrica l system and improper re­
placement of gas discharge (Xenon) head­
light bulbs can cause serious personal in­
jury and death .
Fuses and bulb s 2 79
- Xenon bu lbs are pressur ized and can ex­
plode when being changed.
- Changing Xenon lamps requires the spe­
cial tra ining, instructions and equip­
ment.
- On ly an authorized A udi dealer or other
qualified workshop should change the bulbs in gas discharge lamps.
A WARNING
There are parts with sharp edges on the
openings and on the bulb holders that can
cause ser ious cuts .
- If you are uncertain about what to do,
have the work performed by an author­
ized Audi dealer or othe r qualified work­
shop. Ser ious personal inju ry may result
from imprope rly performed wo rk.
(D Tips
- If you still prefer to replace the light
bulbs you rself, be aware that the engine
compartment is a hazardous area to
work in
c:::> page 21 lc:::> &
- It is best to ask your authorized Audi
dealer whenever you need to change a
bulb.
-
•
•
•

280 Emergency situations
Emergency situations
General
This chapter is intended for trained emer­
gency crews and working personnel who
have the necessary tools and equipment to
perform these ope rations.
Starting by pushing or
towing
Q;) Note
Vehicles w ith an automatic transmission
cannot be started by pus hing o r tow ing.
Starting with jumper
cables
If necessary, the engine can be started by
connecting it to the battery of another vehi­
cle.
If the engine should fail to start because of a
discharged or weak battery, the battery can be
connected to the battery of
another vehicle,
using a
pair of jumpe r cables to start the en­
g ine .
Jumper cables
Use only jumper cables of sufficiently large
cross section to carry the starter current safe­
ly. Refer to the manufacturer's specif ications.
Use only jumper cables with
insulated termi­
na l clamps which are distinctly marked:
plus(+) cable in most cases colored red
minu s(-) cable
in most cases colored black .
A WARNING
Batteries contain electricity, acid, and gas.
Any of these can cause very serious or fatal
inju ry. Follow the instructions below for
safe handling of your veh icle's battery.
- Always shield you r eyes and avoid lean­
ing over the battery whenever possible.
- A discharged battery can freeze at tem­
peratures just be low 32 °F (0 °C). Before connecting a
jumper cable, you must
thaw the frozen battery complete ly, oth­
erwise it could explode.
- Do not allow battery acid to contact eyes
or skin . Flush any contacted area with
water immediately .
- Improper use of a booster battery to start a vehicle may cause an explosion.
- Vehicle batteries generate explosive gas­
es. Keep sparks, flame and lighted ciga­
rettes away from batteries.
- Do not try to jump start any vehicle with a low acid level in the battery.
- The vo ltage of the booster battery must
also have a 12-volt rating. The capacity
(Ah) of the booster battery should not be
lower than that of the discharged bat­
tery . Use of batteries of d ifferent voltage
or substantially different "Ah" rating
may cause an exp losion and personal in­
jury.
- Never charge a frozen batte ry. Gas trap­
ped in the ice may cause an explosion.
- Never charge or use a battery that has
been frozen. The battery case may have
be weakened.
- Use of batter ies of different voltage or
substantially different capacity (Ah) rat­
ing may cause an exp losion and injury.
The capacity (Ah) of the booster battery
should not be lower than that of the dis ­
charged battery.
- Before you check anything in the engine
compartment, always read and heed a ll
WARNINGS
¢page 217.
(D Note
-App lying a higher voltage booster bat­
tery will cause expensive damage to sen­
sitive electronic components, such as
contro l units, relays, radio, etc .
- Th ere must be no electrical contact be­
tween the vehicles as otherwise current cou ld already start to f low as soon as the
positive(+) terminals are connected. .,.

....,
N
0 > co
rl I.O
"'
@ Tips
The discharged battery must be pr operly
connected to the vehicle's electrical sys­
tem. When jump starting or charg ing the
battery, never connect the negative
ground cable to the batte ry negative post
because the ba ttery manager system must
be able to detect the battery's state of
charge. Always connec t the negative
g roun d cab le to t he negative ground pos t
of t he battery manager cont ro l unit.
Using jump start cables
Connect the jump start cables in the e xact or ­
der described below .
Fig . 190 Eng ine co mpar tment : connecto rs for jum p
star t cab le s an d a charger
Fig. 1 91 Jump start in g the batte ry w ith anot her ve hi­
cle: @-dra ined battery ,@ -starte r bat tery
The batte ry is located to the left in the eng ine
compartment.
Do not jump start a frozen or
thawed battery
¢ A in Starting with jumper
cables on page
280 ! Replace the battery. The
p rocedu re for connecting jump start cab les
that is descr ibed next is designed to he lp
jump sta rt your ve hicl e.
Vehicle with drained battery:
~ .. Read the following carefully ¢ page 280 rl
Emergency situ ation s 281
.. Set the parking brake and p lace the selector
lever in the P position.
.. Turn the ignition and e lectr ica l equ ipment
off in both vehicles.
Connecting the negati ve terminal (-) to
the negat ive terminal (- ) ( black )
.. To r each the battery term inals, flip the bat­
tery cover cap to the side ¢
fig. 190.
1. Clamp the end of the red jump start cable
to the terminal (!)¢
fig. 191 on the dead
battery @ ¢CI)
in Starting with jumper
cables on page 280 .
2. Clamp the othe r end of the red jump star t
c able to the termin al@ on t he charging
battery @.
Connect NEGATIVE (-) to NEGATIVE (-)
(black )
3. Clamp the blac k end of t he j ump sta rt ca­
ble
preferably at the ground point , or on
the nega tive terminal @ on the charging
batte ry @ .
4. Clamp the other black end of the jump start cab le
onl y on the ground point@
on your vehicle @ ¢CI).
S. Route the jump start cab les so they can­
not get ca ugh t in the moving parts in the
engine compa rtment.
St arting the engine
6. Start the engine in the vehicle giving the
charge and let it run at idle.
7 . Start the eng ine in the vehicle with the
dead battery and wait two to three m i­
nu tes unti l it "runs smoothly".
8.
If t he engine does not s tart: Stop the
st art ing procedure afte r 10 seco nds and
then repeat it afte r approximately 30 sec­
onds.
9 . In the vehicle that is be ing jump started,
switch the heater fan and rear window de ­
froster on to reduce any voltage peaks
t hat may occur when disconnecting the
j u mper cables . The headlights must be
switched off .
10 . Wi th the e ngin es runn ing , remov e th e ca­
bles in
rever se orde r of the way t hey were ..,.

M N
0 > co ,...., \!) 1.1'1
M 1.1'1 ,....,
A
A/C (automatic climate control system) .. 70
A/C (manual cl imate control system) .. .. 69
Accessories . . . . . . . . . . . . . . . . . . . . 60, 291
Active lane ass ist . . . . . . . . . . . . . . . . . . . . 98
Ac tiva ting vibration warning .. .. .. .. . 100
Adj usting steering time . ... .. .. .. .. . 100
C leaning the camera area . ... .. .. .. . 206
Driver messages . . . . . . . . . . . . . . . . . . . . 99
Indicator light . . . . . . . . . . . . . . . . . . . . . 99
switch ing on and
off ...... .. .. .. .. .. 99
Adapt ive cruise control . . . . . . . . . . . . . . . . 86
Automatic transmission . . . . . . . . . . . . . 90
C lean ing the sensor .... ... .. .. .... . 206
Driver messages .......... .... .. .... 92
General Informa tion . . . . . . . . . . . . . . . . 86
Request fo r driver intervention . . . . . . . . 92
Stop-and-go traffic .......... .... ... 90
Adaptive dampe rs . . . . . . . . . . . . . . . . . . . 106
Indicator light . . . . . . . . . . . . . . . . . . . . . 26
Adapt ive light . . . . . . . . . . . . . . . . . . 47, 106
I ndicator light . . . . . . . . . . . . . . . . . . . . . 25
AdBlue .. .. .. .. ........ ... .. ... ... . 215
F il ling . .. .. .......... ... .... .. .. . 216
M essages .. ............. .. .. .. .. . 215
Adding W indshield washer fluid ....... ... .. 232
Adj usting a ir distribution (Climate control
system) ... .. ................. .. .... 71
Ad justing air vents ......... .. .. .. .. .. 7 2
Adjusting a ir vents (manual climate con-
trol system) . . . . . . . . . . . . . . . . . . . . . . . . . 69
Ad justing a utomatic headlights . ... .. .. 48
Ad justing the cen ter conso le lighting .. .. 50
Ad justing the temperat ure
manual climate control system . . . . . . . . 69
advanced key
refer to Convenience key . . . . . . . . . . . . . 77
A irbag .... .. ................. .. ... 1 44
I ndica tor ligh t . . . . . . . . . . . . . . . . . . . . . 21
Ai rbag system ................ .... .. 165
Advanced Airbag System ... .. .. .. .. . 148
Advanced Airbag System compone nts . 15 2
Ca re ..... .. .... ........... .. .. .. . 160
C hi ld ren . .. ............. .... .. ... 17 2
C hi ld restra ints . .. ..... ... .. .. .. ... 172
Inde x 293
Components (front airbags) .. ... .. .. 152
Danger of fitting a ch ild seat o n the front
passenger seat ... .. . .. ... .... ... .. 146
Disposa l .. .. .. .. ................. 160
Front a irbags . . . . . . . . . . . . . . . . 148, 150
How do the front airbags work? ...... 154
How many a irbags does my vehicle
have? ....... ... .. ..... .......... 152
How the Advanced Airbag System com-
ponent s work togethe r ......... .. .. 15 4
Im portant sa fe ty instructions on the
knee airbag system .. .. ..... ... .. .. 163
Impo rtant t hings to know .... ... .. .. 144
Knee a irbags . .. .. ................. 161
Monitoring .. .. .. ................. 156
PASSENGER AIR BAG OFF light ..... .. 157
Repairs ......... .. ............... 160
Safety i nstr uctions .. . .. .. .. ... ... .. 159
S ide a irbags . .. .... ... .. ..... ..... 163
S ide cur tain airbags . ........... .... 166
Wa rning/Indicato r lights ....... .. .. 156
When must the system be inspected? . 156
Ala rm system
re fer to Anti-theft alarm system ....... 35
A lignment pin (changing the whee l) .. .. 268
A ll- wea ther lights ( LED headlights) ... .. . 46
A ll-wheel d rive
Winter tires . .. .. .. .......... ..... 261
A ll wheel drive .. .. ................. 193
Altern ator
refer to Alternator (indicator light) 20
Alternato r (indicato r light) ...... .... .. 20
Amb ient lighting . ... .. .. .. .... ... .. . 49
A nti- freeze
refer to Eng ine coolan t ......... .. .. 225
Anti -lock braking system ............. 189
Ind icator light ... .. . .. .... .... .. .. . 22
Anti-slip regu lation .. ........... .... 189
Ind icator light . .. .... ........... .. . 22
An ti-theft a larm system ....... ... .. .. . 35
Anti-theft protection Electronic immob ilizer ............. .. 40
Audi active lane assist
refer to Active lane ass ist ......... .. . 98
Audi drive selec t ..... . .. .. ..... ... .. 106
Ind icator light ..... . .. .. ..... ... .. . 26
•
•
•