e39 BMW 530I 1997 E39 Central Body Electronics ZKE Manual

2
Central Body Electronics ZKE III
Objectives of the Module
After completing this module, you will be able to:
• List the functions directly controlled by the GM III.
• Describe how the GM III recognizes the key position from the drivers door.
• Explain what “convenience” features are available from the FZV key.
• Describe how the Seat Module communicates a request for a stored memory position
with the mirror modules.
• List what circuits are controlled by Consumer Cut Off.
• Demonstrate how to Emergency disarm DWA.
• Describe the changes in the 2000 MY Key.
• Explain the electronic influence on power steering assist (Servotronic).
• Demonstrate how to open the sunroof (in the event of an electrical malfunction).
CENTRAL BODY ELECTRONICS (ZKE III)
Models: E38 - 740i(L) and 750iL
E39 - 525i, 528i, 530i, 540i and M5
E53 - X5 3.0i and X5 4.4i
Production Date: E38 1994 to Present
E39 1997 to Present
E53 1999 to Present
Manufacturer: Hella
Pin Connectors: White - 26 pin, Black 26 pin, Black 20 pin (large)

3
Central Body Electronics ZKE III
Central Body Electronics (ZKE III)
Purpose of the System
The Central Body Electronics (ZKE III) system manages the following functions:
GM III
• Windshield Wiping/Washing
• Windsheild Rain Sensor (AIC)
• Headlight Washing
• Tailgate Wiping/Washing
• Interior Lighting
• Central Locking
• Keyless Entry
• Key Memory
• Power Trunk Release
• Electric Opening of Tailgate
• DWA Alarm System
• Servotronics
• Consumer Cut-off/sleep mode
• DiagnosisDriver’s Door Switch Block/
Module
• Power Windows
• Mirror Adjustment/Memory/
HeatingPassenger’s Door Module
• Mirror Adjustment/Memory/
Heating
• Power Windows
Sunroof Module
• Power SunroofSeat/Mirror/ Steering Column
Memory Module
• Seat Adjustment/Memory
• SteeringColumn Adjustment/
Memory
The ZKE III system was introduced on the E38 and is used in the E39 and E53. Most of the
functions operate the same on these vehicles with minor changes and added features to
the system.
ZKE III represents the combination of Body Electronics functions into one central control
module, the General Module (GM).

7
Central Body Electronics ZKE III
Power Distribution
The power distribution box for the
E38 is incorporated in the Electr-
onics box in the engine compart-
ment.
The power distribution box for the
E39 and E53 is inside the vehicle.
The main fuse box is located
inside the glove box above a
hinged panel.
A “pull out” fuse designation card
is also located in the fusebox. This
notes:
• Fuse value in amps
• Location
• Circuit listing by fuse
The placement of the power distribution box is
close to the main electronics carrier behind
the glove box. The modules/relays located in
the electronics carrier include (examples):
• General Module III (GM III)
• Drive away protection (EWS II)
• Anti-lock Brake (ABS/ASC+T)
• Light Check Module (LCM) - behind right kick
panel
• Overload protection relay module
An auxiliary fuse block is located in the trunk
above the battery. In addition to fuses, the
auxiliary fuse block also contains relays (exam-
ples):
• Fuel filler flap lock motor relay
• Fuel pump relay (some vehicles)
• Rear defroster relay
• Unloader relay
FUSE
DESIGNATION
CARDFUSE BOX DROPS
DOWN AFTER TURNING
TWO THUMB SCREWS
12520103.eps
12510104.jpg125101106.jpg

Fused Power Distribution Centers
The E38, E39 and E53 utilize high amperage fused power distribution centers.
The E38 and E39 locations are found under the carpet on the passenger’s side floor and
in the right rear area of the trunk, forward of the battery.
The X5 utilizes a single high amperage fused
power distribution center located next to the
left side EHC air reservoir beneath the cargo
area floor paneling.
8
Central Body Electronics ZKE III
125101107.jpg

Rear Window Wiper/Washer System (E39 Sport Wagon and E53): The system is
included in the scope of ZKE however is not controlled directly by the GM. The control elec-
tronics are integrated into the rear wiper motor assembly. The control electronics contains
two hall sensors, one for monitoring park position and other for the end stop, or to signal
reverse direction of the wiper motor. The control electronics are connected to the vehicle
electrical system via a single seven pin connector.
The rear wiper system is operator controlled
through the wiper stalk switch providing the fol-
lowing functions:
• Intermittent rear window wiping
• Programmed rear window wiping interval
• Operation of the rear window washer
Pressing the wiper stalk forward to the first detent activates the rear wiper in the intermit-
tent mode
. The timed interval is approximately 7-12 seconds. The full sweep and park posi-
tions are recognized by the two hall sensors on the motor gear assembly. If the wiper is
switched OFF, the wiper blade will return to the park position.
The programmed wiper interval procedure is as follows:
• Briefly switch the rear wiper ON/OFF
• Wait the desired interval time
• Switch the rear wiper ON again
• The OFF time will be the programmed interval - up to approx. 30 seconds
Rear window washing is activated by pressing the wiper stalk switch to the full forward
position.
The washer pump operates followed by two full wiping cycles. The wipers will then
switch to the intermittent wiping mode. Additionally, the system automatically controls the
following safety and convenience features:
• Wiper interrupt with the rear glass opened
• Wiping interrupt with a blocked wiper arm
• Continuous wiping when the vehicle is shifted into reverse
When the transmission is shifted into reverse, the wiper will switch to continuous operation
until the vehicle is shifted out of reverse. This signal (high) is provided by the LCM III when
it activates the back up lights.
11
Central Body Electronics ZKE III
12510111.eps

• A remote luggage compartment button is installed in the left kick panel (center console
in the E53) to open the luggage compartment from inside the vehicle.
• The EWS is interfaced for double lock monitoring and unlock function. With the presence
of an accepted EWS key in the ignition, the vehicle will be unlocked and disarm DWA.
• The automatic locking feature (> 99 MY) activates the door locks when a road speed
signal of 5 MPH and engine RPM is detected via the K-Bus. The factory default setting
of this feature is off (can be encoded on for individual users with Key Memory function).
• In the event of an accident (ignition on), the GM will be signalled to unlock all doors.
Hardware Features:
• The external lock cylinders are located in the
driver’s door and luggage compartment lid
(E53/E39 Sport Wagon does not have a tail-
gate lock cylinder).
• The driver’s door and luggage compartment
incorporates an overrunning lock cylinder. The
lock cylinder will free wheel or spin If any key
other than the vehicle key or tool, such as a
screw driver, is inserted into the cylinder. The
lock cylinders can be manually locked/un-
locked by turning the key “past” lock/unlock.
• The door lock buttons are mechanically uncoupled from the
lock actuators when locked.
The door lock buttons “mechanically” lock the individual
doors. This provides manual locking in the event of a central
locking malfunction.
• Child safety locks (located in
the rear doors) are actuated
by inserting a key in the slot on
the door latch or by sliding a
lever (dependent on model).
The door can now only be
opened from outside.
18
Central Body Electronics ZKE III
Door
Button
Lock
12520117.eps
12520119.eps
12510121.eps
12520120.eps

System Components
- with the Principle of Operation
Driver’s Door Lock: The lock/unlock signals
from the driver’s door lock cylinder are input to
the driver’s door module from the two micro
switches on the lock cylinder. The driver’s door
switchblock module carries out the locking func-
tion of the driver’s door.
The windows and sunroof can be closed or
opened by holding the key in the lock/unlock
position (convenience closing/opening feature).
The signal to lock the remaining doors and fuel filler flap is passed over the P-Bus to the
GM III and passenger’s door module. The locking of the passenger’s door is carried out by
the passengers door module. The rear doors, luggage comparment and fuel flap locking
are carried out directly by the GM III. All four doors will be pulled into the double lock posi-
tion when locking from the driver’s door.
The control of the actuators in the front doors is through final stages in the door modules.
The rear doors, trunk and fuel filler flap actuators are controlled by internal relays in the GM
III. When locked, the GM III will not carry out any opening commands from the central lock-
ing button or luggage comparment interior release button.
Luggage Compartment Lock Cylinder (except E53/E39 Sport Wagon): The vehicle
can be locked/ unlocked (prior to 2000 MY) from the luggage compartment lock cylinder.
The lock/unlock micro switch inputs are processed in the GM III and the locking commands
are carried out.
The signal is passed over the P-Bus to the
door modules to lock/unlock the front
doors and the GM III locks the rear doors
and fuel filler flap.
All door actuators are placed in the double
lock position. Removing the key in the hor-
izontal position will activate the valet mode
and prevent the valet key from opening the
luggage comparment.
20
Central Body Electronics ZKE III
12520123.eps
12520124.eps

Door Contact Hall Sensor: Also included in the drivers door actuator is a third hall effect
sensor. This sensor signals the door open/closed status to the GM. This sensor replaces
the door jamb mechanical switch of previous systems. The rotary latch plate position acti-
vates the door contact hall sensor.
• When the door latch is closed, current flow
through the sensor is <5 mA (0).
• When the door is open, current flow through
the sensor is >12 mA (1).
The passenger side front door and both rear
door lock actuators only include this hall effect
sensor (hall sensor 3). Hall sensors 1 & 2 are
not required.
Trunk Lid Close (E38 SCA)/Tailgate and Window Latching System (E39/E53): The
tailgate/trunk lid is opened by any of the three input signals: FZV, remote button and unlock
switch pad (push - trunk lock cylinder E38).
These inputs request the rear latch
actuator control circuit to be
switched to ground (exception:
presence of road speed signal,
key on with FZV request.)
The rear latch actuator unlatches
the mechanism and signals the
GM of the open latch status. The
SCA motor rotates the striker
180
O. Feed-back signalling stops
the motor. E38 - When closing the
trunk lid the trunk latch micro-
switch signals the GM to activate
the SCA motor to pull the lid
down.
Rear window unlatching is requested by the rear window switch ground signal. This signal
initiates activation of the rear window actuator relay control circuit which activates the rear
window actuator. The actuator unlatches the mechanism opening the window. The latch
simultaneously provides an open window signal for the rear window wiper motor module
as well as an interior light on request (via the wiper module).
25
Central Body Electronics ZKE III
12520131.eps
E39 Sport Wagon
Shown
615200097.eps

Tilt Sensor (Liquid Type - E38/E39 to 97 MY): The Tilt Sensor consists of a conductive
liquid chamber, a processor board and metal probes (located in the luggage compartment).
The probes are submersed in the liquid and produce a resistance value dependent on the
tilt of the sensor (angle of vehicle). This resistance value becomes the static point when the
DWA System is armed.
If the vehicle is jacked-up or lifted,
the angle of the liquid changes
producing a change in the resis-
tance value. The sensor recog-
nizes this change and signals the
GM to activate the DWA alarm.
The resets at the new angle. This
allows the DWA to remain armed
and re-activate the alarm if the
vehicle is moved again.
As with the interior sensor, the tilt sensor is also switched OFF when the vehicle is locked
two times within ten seconds. The LED will flash one time for confirmation. This allows the
sensor to be switched OFF for transportation purposes.
Tilt Sensor (Electronic Type from 98 MY): Located in the luggage comparment area,
the tilt sensor is an electronic sensing device with the sole purpose of monitoring the vehi-
cle's parked angle when DWA is armed.
The sensor requires three signal wires to func-
tion:
• KL 30 - Constant battery voltage
• Signal "STDWA"; switched ground input sig-
nal provided by the GM indicating DWA
armed/disarmed status.
The tilt sensor is used as a splice location for
the STDWA signal to the Siren and UIS int-
erior protection sensor.
36
Central Body Electronics ZKE III
625200107.eps

39
Central Body Electronics ZKE III
System Components: Inputs - Processing - Outputs
97 MY E39 Shown