instrument panel BUICK LESABRE 2001 Owner's Guide

2-67
The main components of your instrument panel are the following:
A. Air Outlets
B. Driver Information Center Buttons (If Equipped)
C. Turn Signal/Multifunction Lever
D. Steering Wheel Controls (If Equipped)
E. Hazard Warning Flashers
F. Instrument Panel Cluster
G. Traction Control Button (If Equipped)
H. Exterior LampsI. Head
-Up Display (HUD) Controls (If Equipped)
J. Hood Release
K. Parking Brake
L. Cruise Controls
M. Audio System
N. Climate Controls
O. Glove Box

2-68
Instrument Panel Clusters
Your instrument panel cluster is designed to let you know at a glance how your vehicle is running. You'll know how
fast you're going, how much fuel you're using, and many other things you'll need to drive safely and economically.
Your vehicle is equipped with one of these instrument panel clusters, which includes indicator warning lights and
gages that are explained on the following pages.
Standard Cluster (United States version shown, Canada similar)

2-72 Air Bag Readiness Light
There is an air bag readiness light on the instrument
panel, which shows AIR BAG. The system checks the
air bag's electrical system for malfunctions. The light
tells you if there is an electrical problem. The system
check includes the air bag sensors, the air bag modules,
the wiring and the crash sensing and diagnostic module.
For more information on the air bag system, see
ªAir Bagº in the Index.
This light will come on
when you start your vehicle,
and it will flash for a few
seconds. Then the light
should go out. This means
the system is ready.
If the air bag readiness light stays on after you start the
vehicle or comes on when you are driving, your air bag
system may not work properly. Have your vehicle
serviced right away.
CAUTION:
If the air bag readiness light stays on after you
start your vehicle, it means the air bag system
may not be working properly. The air bags in
your vehicle may not inflate in a crash, or they
could even inflate without a crash. To help avoid
injury to yourself or others, have your vehicle
serviced right away if the air bag readiness light
stays on after you start your vehicle.
The air bag readiness light should flash for a few
seconds when you turn the ignition key to RUN.
If the light doesn't come on then, have it fixed so
it will be ready to warn you if there is a problem.

2-79
Here are some things you need to know in order to help
your vehicle pass an inspection:
Your vehicle will not pass this inspection if the SERVICE
ENGINE SOON light is on or not working properly.
Your vehicle will not pass this inspection if the OBD
(on
-board diagnostic) system determines that critical
emission control systems have not been completely
diagnosed by the system. The vehicle would be
considered not ready for inspection. This can happen
if you have recently replaced your battery or if your
battery has run down. The diagnostic system is designed
to evaluate critical emission control systems during
normal driving. This may take several days of routine
driving. If you have done this and your vehicle still
does not pass the inspection for lack of OBD system
readiness, see your dealer or qualified service center to
prepare the vehicle for inspection.
Oil Pressure Light
If your vehicle has the
standard instrument panel
cluster, this light will come
on if there is a problem
with your vehicle's engine
oil pressure.
If your vehicle has the optional gage cluster, you
can read your oil pressure directly from the Driver
Information Center (DIC). See ªDIC Displays and
Controlsº in the Index.
The oil pressure light will come on briefly when you
turn your key to RUN. That's just a check to be sure
the light works. This is normal and doesn't show a
problem. If it doesn't come on and then go off,
be sure to have it fixed so it will be there to warn
you if there is a problem.

2-92
The information may be displayed in English or metric
units and appears as a reflection in the windshield.
The HUD consists of the following information:

Speedometer Reading

Turn Signal Indicators

High
-Beam Headlamp Indicator

Check Gages Message
The HUD shows these images when they are lighted on
the instrument panel cluster.
Be sure to continue scanning your displays, controls
and driving environment just as you would in a vehicle
without HUD. If you never look at your instrument
panel, you may not see something important, such as
a warning light.
NOTICE:
Although the HUD image appears to be near the
front of the vehicle, do not use it as a parking aid.
The HUD was not designed for that purpose.
If you try to use the display as a marker for the
front of your vehicle, such as in a parking lot,
you may misjudge distance and hit an obstacle
or another vehicle.

2-93
The HUD controls are located on the instrument panel to
the left of the steering wheel.1. Start your engine and slide the HUD dimmer control
all the way up.
The brightness of the HUD image is determined by
an internal photo
-cell, and where you have the HUD
dimmer control set.
2. Adjust the seat to your driving position. Slide the
image height adjuster control all the way up, raising
the image as far as possible.
3. Now push the image height adjuster control down so
the image is as low as possible but still in full view.
4. Slide the dimmer control downward until the HUD
image is no brighter than necessary.
To turn the HUD display off, slide the dimmer control
all the way down.

3-3
Temperature Lever
This lever adjusts the temperature of the air coming
through the system. Move the TEMPERATURE lever to
change the temperature of the air coming through your
outlets. Move the lever between COOL and WARM to
lower or raise the temperature.
Mode Controls
The buttons on your system allow you to choose
settings to deliver air through the lower, middle or
windshield outlets.
RECIRC: Press this button to limit the amount of
outside air entering your vehicle. This is helpful when
you are trying to cool the interior of the vehicle quickly,
or limit the amount of outside air entering your vehicle.
To turn off RECIRC, press the button again. If you
select FRONT defrost or BLEND while RECIRC is
selected, the system will automatically turn off RECIRC
to prevent fogging. If you select RECIRC while in
FRONT defrost, the RECIRC light will flash three times
to let you know this is not allowed.VENT: This setting directs outside air through the
middle instrument panel outlets. The air conditioning
compressor is not working when VENT is selected.
If you select VENT while in FRONT defrost, the VENT
light will flash three times to let you know this is not
allowed. This is to prevent fogging.
HTR: This button directs air out of the heater outlets.
Most of the air will come from the floor outlets while
some air will flow through the windshield and side
window outlets. The air conditioning compressor is not
working when HTR is selected.
BLEND: When BLEND is selected, the airflow will
be split between the windshield and the floor outlets.
The air conditioning compressor will be operating.
FRONT: This setting directs most of the airflow toward
the windshield.
OFF: The ventilation system always allows fresh
air to flow through your vehicle when it is moving.
The system will try to keep the air at a previously
chosen temperature. When the system is off, the
blower fan is also off.

3-4
MAX: This setting directs airflow through the middle
instrument panel outlets. The amount of outside air
entering your vehicle is limited with this setting. The air
conditioning compressor is on in this mode.
Also in this mode, the RECIRC function is activated to
create the maximum cooling effect in the vehicle. If
RECIRC was active before selecting MAX, the light in
the RECIRC button will go off. If RECIRC is selected
after MAX, the light in the RECIRC button will not
come on.
NORM: This setting cools the outside air entering your
vehicle and directs it through the middle instrument
panel outlets. The air conditioning compressor is on in
this mode.
BI
-LEV: This setting directs warm air to the floor and
cooler air to the middle instrument panel outlets. The air
conditioning compressor is on in this mode.
Dual Automatic ComforTemp

Climate Control (If Equipped)
If your vehicle is equipped with the Dual Automatic
ComforTemp Climate Control system, the following
information tells you how it works.
You will hear a beep each time a button is pushed and a
light on the button will indicate which function is active.
The lights are on all buttons except TEMP, FAN and
AIR FLOW. The display will show fan speed, comfort
level setting and airflow direction for a few seconds
whenever AUTO is selected, and then it will display the
outside temperature. The outside temperature reading is
most accurate when the vehicle is moving. During stops,
the display shows the previous temperature for best
accuracy and system control.

3-8 Air Conditioning
On hot days, open the windows long enough to let hot
inside air escape. This reduces the time it takes for your
vehicle to cool down. Then keep your windows closed
for the air conditioner to work its best.
If you have the electronic touch system, for quick
cool
-down on very hot days, use MAX with the
temperature and fan speed adjusted to COOL and
HIGH. If this setting is used for long periods of time,
the air in your vehicle may become too cold and dry.
For normal cooling on hot days, use NORM and adjust
the temperature and fan speed for your comfort. If
RECIRC is selected while in the NORM air
conditioning mode, the system works like MAX and
recirculates the air.On sunny days, when the air is moderately warm or
cool, use BI
-LEV to deliver warm air to the floor and
cooler air to the middle instrument panel outlets. On
days like these, the sun may adequately warm your
upper body, but your lower body may not be warm
enough. To warm or cool the air delivered, adjust the
TEMPERATURE lever.
The amount of fresh air entering the vehicle is limited
when RECIRC is selected. This is helpful when you are
trying to cool the air in your vehicle or limit the air
entering the vehicle.
If your vehicle has the Dual Automatic ComforTemp

system and it is set for AUTO, on very hot days, the
system will automatically enter the RECIRC mode and
the temperature door will be positioned at the full cold
position for maximum cooling. If the system is not in
the AUTO mode, RECIRC should be selected to provide
maximum cooling. You can choose the extreme comfort
setting of 60
F (16
C), but the system will not cool any
faster by choosing the extreme comfort setting.

3-11 Passenger Control (If Equipped)
If your vehicle is equipped with the Dual Automatic
ComforTemp
system, the front seat passenger
can control the air temperature in their seating area.
The control is located on the passenger's door armrest.
The temperature can be set up to 5
F (3
C) cooler
or warmer than the primary setting. To activate the
passenger control, simply press the button with the red
arrow to increase temperature. Each time you press the button, a red indicator light will
come on. To decrease temperature, press the button with
the blue arrow. Each time you press the button a blue
indicator light will come on.
If the passenger control has been turned on, it can be
turned off by pressing the OFF button on the main
system once. Pressing the OFF button a second time
will turn off the main system.
Ventilation System
For mild outside temperatures when little heating or
cooling is needed, use VENT (on the electronic touch
system or manual operation on the Dual Automatic
ComforTemp system) to direct outside air through
your vehicle. Air will flow through the middle
instrument panel outlets.
Your vehicle's flow
-through ventilation system supplies
outside air into the vehicle when it's moving. When the
vehicle is not moving, you can get outside air to flow
through by selecting any air choice (except the rear
window defogger) and any fan speed.