ECO mode CADILLAC ELDORADO 2002 10.G User Guide

3-11 AM-FM Stereo with Cassette Tape Player
Playing the Radio
PWR (Power): Press this knob to turn the system on
and off.
VOL (Volume): Turn this knob clockwise to increase
volume. Turn it counterclockwise to decrease volume.
The volume level will appear on the display.HR (Hour) or MN (Minute): Display the time with
the ignition off by pressing this button.
DSPL (Display): Pressing this button will display the
station being played.
Finding a Station


BAND
: Press this button to select AM,
FM1 or FM2.


TUNE
: Press and release this button to tune
to the next or previous radio station.


SEEK
: Press and hold this button until a chime
sounds. Next or previous radio stations are advanced to
in small increments until the SEEK button is released.
Seeking stops when you release this button. If you
press and hold the SEEK button again within five
seconds of being in seek mode, seeking will continue.
Waiting longer than five seconds places the radio back
in tune mode.

3-14


REV (Reverse): Press the left arrow to rewind the
tape rapidly. The radio will play while the tape reverses
and REV will appear on the display. You may use your
station pushbuttons to tune to another radio station while
in reverse mode. Press the left arrow again to return to
playing speed.
FF
(Fast Forward): Press the right arrow to fast
forward to another part of the tape. The radio will play
while the tape advances and FF will appear on the
display. You may use your station pushbuttons to
tune to another radio station while in fast forward mode.
Press the right arrow again to return to playing speed.


SEEK
: Press the right arrow to seek to the next
selection on the tape. Press the left arrow to search for
the previous selection on the tape (REP will appear on
the display). Your tape must have at least three seconds
of silence between each selection for seek to work. The
sound will mute while seeking.SCAN: Press this button to listen to selections for a
few seconds. SCAN FF will appear on the display until
the next selection is found and then SCAN PLAY will
appear on the display. The tape will go to a selection,
play for a few seconds, then go on to the next selection.
Press this button again to stop scanning.
~SIDE!: Press this button to change the side of the
tape that is playing. (PLAY shows on the display.)


SOURCE
: Press this button to select a source.
If no cassette tape is in the tape player, CASS appears
on the display and then the radio station appears briefly.
The display then reverts back to showing the time of
day. Press this button again or press BAND to switch
back to the radio.
(Eject): Press this button to stop a tape when
it is playing or to eject a tape when it is not playing.
Eject may be activated with the radio off. Cassette tapes
may be loaded with the radio off but they will not start
playing until the PWR knob is pressed. Press PWR
or turn the ignition off to stop the cassette tape player.
The tape will stay in the player and resume play at the
point where it stopped.

3-17
Finding a Station
BAND: Press this button to select AM, FM1, FM2 or
weather.
~'TUNE SEEK!': When this button is pressed it
has two positions. Press this button to the first position
to manually tune to the next or previous stations. If this
button is held at the first position for a few seconds,
the radio will continue tuning until this button is
released. Press this button to the second position and
release to seek to the next or previous radio station.
SCAN: Press this button for less than two seconds
to scan radio stations. The radio will go to a station,
play for five seconds, then go on to the next station.
Press this button again to stop scanning.
To scan preset stations, press and hold SCAN for more
than two seconds until you hear a beep. The radio will
go to the first preset station stored on your pushbuttons,
play for five seconds, then go on to the next preset
station. Press SCAN again to stop scanning. The radio
will scan preset stations with a strong signal only.Setting Preset Stations
The six numbered pushbuttons let you return to your
favorite stations and associated tone and DSP settings.
The RDS PTY mode must be off to use this mode.
You can set up to 24 stations (six AM, six FM1, six FM2
and six weather), by performing the following steps:
1. Turn the radio on.
2. Press BAND to select AM, FM1, FM2 or weather.
3. Tune in the desired station.
4. Press and hold one of the six numbered pushbuttons
for more than two seconds. Whenever you press that
numbered pushbutton for less than two seconds,
the station you set will return.
5. Repeat the steps for each pushbutton.
When battery power is removed and later applied,
you will not have to reset your radio presets because
the radio remembers them.

3-19
Using RDS
Your audio system is equipped with Radio Data Systems
(RDS). RDS mode gives you many useful new features.
With RDS the radio can do the following:

Seek only to stations with the types of programs
you want to listen to,

seek to stations with traffic announcements,

receive announcements concerning local and
national emergencies,

receive and display messages from radio stations and

search for a stronger station when a station is too
weak for listening.
RDS features are only available for use on FM stations
which broadcast RDS information.
(RDS Select): Press this button to use the
alternate RDS functions (RDS, TA, MSG, PTY and
the PTY arrows).HR (Hour) or MN (Minute): Press the RDS select
button, followed by one of these buttons to display the
time of the current station. STATION TIME IS will be
displayed. If a time has not been sent to the radio,
NO STATION TIME will be displayed. If you have
recently tuned to the station, you may need to wait a
minute before the time is available to the radio. To set
the clock to the current displayed station time, press and
hold HR or MN until TIME UPDATED is displayed.
There is a two second delay before the time is updated.
RDS does not have to be on to use this function,
but you must be tuned to an FM RDS station.
REGION: Press the RDS select button, then press
and hold the RDS pushbutton for two seconds.
REGION: ON will appear on the display. When an
RDS station becomes weak, this function searches for
a stronger station within the same network. A network
can span a great distance. One network can have stations
spread across a country or continent. Each network
breaks down into regions. With regions, local news
items like weather and traffic are available to you.
When the region function is on, the radio only searches
for stations in the same network and region. You can
only use the region function when RDS is on. Press the
RDS pushbutton again to turn the region function off.
REGION: OFF will appear on the display.

3-21
Setting a PTY Preset Stations
The six numbered pushbuttons let you return to your
favorite PTYs. These pushbuttons have factory presets.
See ªRadio Data Systems (RDS) Program Type (PTY)
Selectionsº in the Index. You can set up to 12 PTYs
(six FM1 and six FM2), by doing the following:
1. Turn PTY on.
2. Press BAND to select FM1 or FM2.
3. Tune in an RDS station with the PTY you desire.
4. Press and hold one of the six numbered pushbuttons
for more than two seconds until you hear a beep.
Whenever you press that pushbutton for less than
two seconds, the PTY you set will return.
5. Repeat the steps for each pushbutton.
When battery power is removed and later applied,
you will not have to reset your RDS presets because
the radio remembers them.RDS Messages
ALERT: This type of announcement warns of national
or local emergencies. You will not be able to turn off
alert announcements. Alert announcements will come
on even if RDS mode is turned off. ALERT appears
on the display when an alert announcement plays.
The radio uses TA volume during these announcements.
To increase volume, turn the VOL knob clockwise.
Turn it counterclockwise to decrease volume.
TA VOLUME will appear on the display while the
volume is being adjusted. When an alert announcement
comes on the current radio station or a related network
station, you will hear it, even if the volume is muted
or a cassette tape or compact disc is playing. If the
radio tunes to a related network station for an alert
announcement, it will return to the original station
when the announcement is finished. If the cassette tape
or compact disc player is playing, play will stop for the
announcement and resume when the announcement
is finished.

8-7 Reaching Roadside Service
Dial the toll-free Roadside Service number:
1
-800-882-1112. An experienced Roadside
Service Advisor will assist you and request the
following information:

A description of the problem

Name, home address, home telephone number

Location of your Cadillac and number you are
calling from

The model year, Vehicle Identification
Number (VIN), mileage and date of delivery
Roadside Service for the Hearing or
Speech Impaired
Roadside Service is prepared to assist owners who have
hearing difficulties or are speech impaired. Cadillac has
installed special telecommunication devices called Text
Telephone (TTY) in the Roadside Service Center.
Any customer who has access to a (TTY) or a
conventional teletypewriter can communicate with
Cadillac by dialing from the United States or Canada
1
-888-889-2438 -- daily, 24 hours.