wiper blades CADILLAC STS V 2007 1.G Owners Manual
[x] Cancel search | Manufacturer: CADILLAC, Model Year: 2007, Model line: STS V, Model: CADILLAC STS V 2007 1.GPages: 560, PDF Size: 2.92 MB
Page 189 of 560
Windshield Wipers
The lever on the right side of the steering column
operates the windshield wipers.
7(Mist):Pull the lever down and release it for
a single wiping cycle. The lever will return to its
original position. For more cycles, hold the
lever down before releasing it.
9(Off):Put the lever in this position to turn off
the wipers.
&(Delay):Put the lever in this position to set a
delay between wipes. Turn the delay adjustment
band to set the length of the delay.
x(Delay Adjustment):Use this band to set the
length of the delay between wipes when using the
delay feature. The closer you move the band
toward mist, the longer the delay. The windshield
wiper lever must be in delay for this feature to work.
6(Low Speed):Put the lever in this position
for slow, steady wiping cycles.
1(High Speed):Put the lever in this position
for rapid wiping cycles.
If the windshield wipers are in use for about
six seconds while you are driving, the exterior
lamps will come on automatically if the exterior
lamp control is in AUTO. SeeWiper Activated
Headlamps on page 215for more information.
Be sure to clear ice and snow from the wiper
blades before using them. If they’re frozen to the
windshield, gently loosen or thaw them. If the
blades do become damaged, install new blades.
For more information, seeWindshield Wiper Blade
Replacement on page 419.
189
Page 190 of 560
Heavy snow or ice can overload the wiper motor. A
circuit breaker will stop the motor until it cools down.
Clear away snow or ice to prevent an overload.
Your vehicle (STS-V only) is equipped with a
feature that disables the wiper system when the
hood is open and your vehicle is stopped. Opening
the hood will automatically park the wipers if
they are not parked. This prevents the wipers from
interfering with hood operation. Be sure the
hood is not opened when you require the vehicle’s
wipers out of the park position, such as when
changing the wiper blades.
Rainsense™ II Wipers
If your vehicle has this feature, the moisture
sensor is mounted on the interior side of the
windshield behind the rearview mirror. It is used to
automatically operate the wipers by monitoring
the amount of moisture build-up on the windshield.
Wipes occur as needed to clear the windshield
depending on driving conditions and the sensitivity
setting. In light rain or snow, fewer wipes will
occur. In heavy rain or snow, wipes will occur more
frequently. The Rainsense™ wipers operate in adelay mode as well as a continuous low or high
speed as needed. If the system is left on for long
periods of time, occasional wipes may occur
without any moisture on the windshield. This is
normal and indicates that the Rainsense™ system
is activated.
To activate the Rainsense™ system, turn the
wiper band to delay mode and select one of the
four sensitivity levels indicated on the wiper stalk.
The position closest to off is the lowest sensitivity
setting, level one. This allows more rain or snow to
collect on the windshield between wipes. Turning
the wiper band away from you to higher sensitivity
levels increases the sensitivity of the system and
frequency of wipes. The highest sensitivity setting,
level four, is closest to low. A single wipe will occur
each time you turn the wiper stalk to a higher
sensitivity level to indicate that the sensitivity level
has been increased.
Notice:Going through an automatic car wash
with the wipers on can damage them. Turn
the wipers off when going through an
automatic car wash.
190
Page 335 of 560
Driving in Rain and on Wet Roads
Rain and wet roads can mean driving trouble. On a
wet road, you cannot stop, accelerate, or turn as
well because your tire-to-road traction is not as
good as on dry roads. And, if your tires do not have
much tread left, you will get even less traction.It is always wise to go slower and be cautious if rain
starts to fall while you are driving. The surface may
get wet suddenly when your re exes are tuned for
driving on dry pavement.
The heavier the rain, the harder it is to see. Even if
your windshield wiper blades are in good shape, a
heavy rain can make it harder to see road signs and
traffic signals, pavement markings, the edge of the
road, and even people walking.
It is wise to keep your windshield wiping equipment
in good shape and keep your windshield washer
uid reservoir lled with washer uid. Replace your
windshield wiper inserts when they show signs of
streaking or missing areas on the windshield,
or when strips of rubber start to separate from
the inserts.
335
Page 341 of 560
Here are some things you can check before a trip:
Windshield Washer Fluid:Is the reservoir
full? Are all windows clean inside and outside?
Wiper Blades:Are they in good shape?
Fuel, Engine Oil, Other Fluids:Have you
checked all levels?
Lamps:Are they all working? Are the
lenses clean?
Tires:They are vitally important to a safe,
trouble-free trip. Is the tread good enough
for long-distance driving? Are the tires
all in ated to the recommended pressure?
Weather Forecasts:What is the weather
outlook along your route? Should you
delay your trip a short time to avoid a major
storm system?
Maps:Do you have up-to-date maps?
Highway Hypnosis
Is there actually such a condition as highway
hypnosis? Or is it just plain falling asleep at the
wheel? Call it highway hypnosis, lack of
awareness, or whatever.
There is something about an easy stretch of road
with the same scenery, along with the hum of the
tires on the road, the drone of the engine, and the
rush of the wind against the vehicle that can make
you sleepy. Do not let it happen to you! If it does,
your vehicle can leave the road in less than a
second, and you could crash and be injured.
What can you do about highway hypnosis?
First, be aware that it can happen.
Then here are some tips:
Make sure your vehicle is well ventilated, with
a comfortably cool interior.
Keep your eyes moving. Scan the road ahead
and to the sides. Check your rearview mirrors
and your instruments frequently.
If you get sleepy, pull off the road into a rest,
service, or parking area and take a nap, get
some exercise, or both. For safety, treat
drowsiness on the highway as an emergency.
341
Page 360 of 560
Tires............................................................ 421
Winter Tires.............................................. 422
Tire Sidewall Labeling............................... 423
Tire Terminology and De nitions............... 426
Run-Flat Tires (STS-V).............................. 429
In ation - Tire Pressure............................. 431
High-Speed Operation............................... 432
Tire Pressure Monitor System................... 433
Tire Inspection and Rotation...................... 438
When It Is Time for New Tires.................. 440
Buying New Tires...................................... 441
Different Size Tires and Wheels................ 443
Uniform Tire Quality Grading..................... 444
Wheel Alignment and Tire Balance............ 445
Wheel Replacement.................................. 445
Tire Chains............................................... 447
Lifting Your Vehicle (STS-V)...................... 448
If a Tire Goes Flat.................................... 451
Tire In ator Kit.......................................... 452
Changing a Flat Tire................................. 464
Removing the Spare Tire and Tools.......... 465
Removing the Flat Tire and Installing
the Spare Tire....................................... 466Storing a Flat or Spare Tire and Tools...... 473
Compact Spare Tire.................................. 475
Appearance Care........................................ 476
Cleaning the Inside of Your Vehicle.......... 476
Fabric/Carpet............................................. 477
Leather...................................................... 478
Instrument Panel, Vinyl, and Other
Plastic Surfaces..................................... 479
Wood Panels............................................. 479
Speaker Covers........................................ 479
Care of Safety Belts.................................. 479
Weatherstrips............................................ 480
Washing Your Vehicle............................... 480
Cleaning Exterior Lamps/Lenses................ 480
Finish Care............................................... 481
Windshield and Wiper Blades.................... 481
Aluminum or Chrome-Plated Wheels......... 482
Tires......................................................... 483
Sheet Metal Damage................................. 483
Finish Damage.......................................... 483
Underbody Maintenance............................ 483
Chemical Paint Spotting............................ 484
Vehicle Care/Appearance Materials............ 484
Section 5 Service and Appearance Care
360
Page 419 of 560
2. Pull out the push pins holding down the top
portion of the cloth cover.
3. Fold the cover down slightly and locate the
lamp assembly.
4. Turn the socket counterclockwise and pull it
straight out to remove it from the lamp
assembly.
5. Pull the old bulb straight out and reinstall the
new bulb.
6. Reverse the steps to reinstall.
Replacement Bulbs
Exterior Lamp Bulb Number
Back-up 3157K
For replacement bulbs not listed here, contact
your dealer.
Windshield Replacement
Keep in mind that your windshield is part of the
Head-Up Display (HUD) system. If you ever have
to get your windshield replaced, be sure to get
one that is designed for HUD or your HUD image
may look blurred or out of focus.
Windshield Wiper Blade
Replacement
Windshield wiper blades should be inspected for
wear or cracking. SeeScheduled Maintenance
on page 505.
It’s a good idea to clean or replace the wiper
blade assembly on a regular basis or when worn.
For proper windshield wiper blade length and
type, seeNormal Maintenance Replacement Parts
on page 518.
419
Page 420 of 560
STS-V models will automatically move the
windshield wipers to the park position if the hood
is open. Make sure the hood is closed before
replacing your windshield wiper blades.
To replace the wiper blade assembly, do the
following:
1. Pull the windshield wiper assembly away from
the windshield.
2. Squeeze the tabs on each side of the wiper
blade assembly and slide the assembly off
the end of the wiper arm.3. Replace the blade assembly with a new one.
Allowing the wiper blade arm to touch the
windshield when no wiper blade is installed
could damage the windshield. Any damage
that occurs would not be covered by your
warranty. Do not allow the wiper blade arm to
touch the windshield.
4. Repeat the steps for the other wiper.
420