radiator CHEVROLET CAMARO 1967 1.G Chassis Repair Manual

CHASSIS SHEET METAL 11-13

HOOD ADJUSTMENT

The alignment of the hood in relation
to*
other sheet

metal parts is controlled by the position of the hood

hinges and the height of the two bumpers, located one at

each end of the radiator support. The adjustments at

the hood latch must be made after the hinges and bumpers

are positioned to yield the dimensions shown in Figure

17.
Latch adjustments are made so that effort required

to open and close the hood is reasonable, and hood align-

ment obtained by hinge and bumper adjustment is main-

tained when the hood is closed. Note that the hood latch

is not designed or intended to correct basic hood align-

ment faults.

To align the hood and lock, proceed as follows:

HOOD HINGE (Fig. 18)

1.
Note that the mounting holes in the body-mounted

end of the hinge are slotted to provide up and down

movement of the hood assembly while the hood

mounted end is slotted to provide fore and aft move-

ment.

2.
Scribe a mark around the entire hinge plate which

will be involved in the adjustment.

3.
Loosen the appropriate screws and shift the position

of the hood on the hinge plate the approximate amount

to correct misalignment, using the scribed marks to

check amount of movement. Check condition of ad-

justment by tightening cap screws and closing hood.

Fig.
18 - Hood Hinge - Chevy II
Fig.
19 - Hood Lock, Catch and Support - Chevy II

HOOD BUMPERS

Hood bumpers must be adjusted until hood and fender

line up as shown in Figure 17.

HOOD CATCH AND LOCK (Fig. 19)

Hood lock plate mounting holes are slotted to provide

fore and aft adjustment of the hood lock bolt. The hood

lock bolt itself is adjustable for up and down positioning

of the lock bolt head so that its proper engagement in the

latch assembly may be provided for. The distance that

the lock bolt protrudes out of the lock plate should be

adjusted so that the hood bumpers are slightly com-

pressed by the fully latched hood and so that the effort

required to release the hood catch is reasonable.

FENDER ADJUSTMENT (Figs. 17 and 20)

DO NOT CHANGE SKIRT ASSEMBLY-TO-DASH SHIM-

MING IN AN EFFORT TO ADJUST THE DOOR-TO-

FENDER GAP OR ANY OTHER SHEET METAL AP-

PEARANCE ITEM.

The front fenders are shimmed independently of the

skirt assemblies, unlike conventional- vehicles on which

almost the entire front end sheet metal assembly is

shimmed and adjusted as a unit.

Figure 20 shows the locations of front fender shims.

1.
The rocker panel extension location allows adjust-

ment to make fender outer surface flush with door

outer surface.

2.
The upper or plenum chamber location provides a

means of adjusting fender upper surface so that it

is flush with the upper surface of the cowl.

3.
The locations atop the skirt assembly are shimmed

to close the gap created between the fender mounting

flange and skirt assembly when the plenum chamber

CHEVROLET CHASSIS SWVICE MANUAL

CHASSIS SHEET METAL 11-14

location is shimmed; thus keeping the fender mount-

ing bolts from crushing in the fender mounting

flange.

If shimming is done without the fenders being disas-
asembled, it is suggested that fender mounting bolts

rearward of radiator support be loosened while shims

are inserted and sheet metal fit is checked. Tighten

shimmed mounting bolts first, then all others.

COMPONENT PART REPLACEMENT

BATTERY TRAY (FIG. 21)

Removal

1.
Disconnect battery cables.

2.
Remove screw retaining battery hold down clamp.

3.
Remove battery from vehicle.

4.
Remove screws retaining tray assembly to fender

skirt and support, and remove tray from vehicle.

Installation

Reverse removal procedure.

RADIATOR SUPPORT (FIG. 22)

Removal

1.
Remove grille and related components (Section 13).

Remove battery tray as outlined in this section.

Remove shroud attaching screws and remove shroud

if vehicle is so equipped.

Remove horn relay, horns, voltage regulator, and

wiring harness from radiator support.

Remove shroud and radiator (Section 13)o

Remove screws attaching radiator support to frame,

skirts,
fenders.

Remove radiator support from vehicle (fig. 23).

Installation

1.
Position radiator support in vehicle; align mounting

screw and bolt holes with drift punch.

Install screws and bolts loosely until all are started,

then tighten.

3.
Complete installation following removal procedure in

reverse order. Refer to torque specifications at rear

of manual for correct torque values.

4.
Aim headlamps as outlined in Section 12.

FRONT FENDER ASSEMBLY

Removal

1*
Remove headlamp dooro

2.
Open hood and remove screws joining fender top
2.

Fig. 20 - Front Fender Shimming
Fig.
21 - Battery Tray

flange to skirt. Remove, and record number of

shims at first cap screw forward of windshield (fig.

24).

3.
Remove screw located on upper surface of headlamp

cavity.

4.
From under forward end of fender, remove screw

retaining fender to radiator support.

5.
From inboard side of rocker panel extension, remove

cap screw retaining fender to extension. Remove,

and record number of shims.

6. Separate headlamp filler panel from fender by re-

moving remaining screws.

7.
Remove fender from vehicle.

Installation

1.
Inspect condition of cowl-to-fender seal and replace,

if necessary, as shown in Figure 25.

2.
Install headlamp filler panel on fender.

3.
Position fender on vehicle. Note that eowl-to-fender

seal must be positioned so that outer edge points

toward front of vehicle. Align all mounting screw

and bolt holes with drift punch and install all screws

and bolts loosely. Do not tighten any screws or bolts

until all are started. Refer to removal rocedure

for screw and bolt locations.

4.
Replace shims taken out when fender was removed

from vehicle and continue as outlined under Main-

tenance and Adjustments—Fender Adjustment.

5.
Install headlamp door and cheek headlamp aiming

as outlined in Section 12.

CHEVROLET CHASSIS SERVICE MANUAL

CHASSIS SHEET METAL 11-15

FRONT FENDER TRIM

If fender spear molding is to be replaced without re-

moving fender from vehicle, proceed as follows:

1.
Perform Operations 2 and 5 only of Front Fender

Assembly—Removal.

2.
Pull rear* end of fender away from body far enough

to insert a short piece of 2 x 4 between lower rear

corner of fender and rocker panel extension.

3.
It should now be possible to gain access to first and

second retaining nuts forward of rear end of fender.

All other nuts can be reached from front wheel

opening.

SKIRT ASSEMBLY

Removal

1.
Remove hood and hinge assemblies as outlined in

this section.

2.
Remove grille and radiator support as outlined in

Section ia.

3.
Remove fender assembly as outlined in this section.

4.
Raise car from floor and place jack stands under

rocker panel extension.
5.
Remove suspension bumper support, shock absorber,

front spring and stabilizer link as outlined in Section

3.

6. If removing left skirt assembly, remove steering

gear mounting bolts, power steering hose clamp (if

so equipped) and outer (left) clutch cordon shaft

bracket (if so equipped).

7.
Remove tie rod ball stud from steering arm as out-

lined in Section 9.

8. Support engine and remove engine mount cushion as

outlined in Section 6.

9. Remove spring clip from brake line junction which

passes through skirt and remove junction from skirt

(see Section 5).

10.
Remove four bolts retaining front crossmember to

skirt.

11.
Remove four bolts retaining skirt assembly to dash

front brace. Remove 3 bolts retaining upper end of

skirt to dash (fig. 26); record shims removed.

12.
Remove skirt assembly with remaining suspension

parts attached as shown in Figure 27.

13.
Suspension parts may be detached as outlined in

Section 3.

Fig.
22 - Radiator Support Assembly

CHEVROLET CHASSIS SERVICE MANUAL

CHASSIS SHEET METAL 11-16

Fig. 23 - Removing Radiator Support from Vehicle

Inspection

If car has been involved in a collision it is advisable

to carefully inspect cowl and dash area for damage.

Check front of dash area following directions in Fisher

Body Manual. Pay particular attention to welds, cage

nuts,
weld nuts and skirt mounting surfaces. Cage and

weld nuts may be repaired by outright replacement (the

best method); or by the installation of spiral thread in-

serts.
If the spiral inserts are used, follow the instruc-

tions furnished by the manufacturer.

COWL
Fig. 25 - Replacing Fender Seal

Fig. 26 - Skirt Mounting Bolts

Fig. 24- Fender Mounts

Fig. 27 - Removing Skirt Assembly

CHEVROLET CHASSIS SERVICE MANUAL

CHASSIS SHEET METAL 11-17

Fig.
28- Hood Spring Removal

Installation

Skirt installation is written for the installation of a

stripped skirt, with suspension and otiier parts added

after skirt is attached to vehicle. Proceed as follows:

1.
Position skirt assembly on vehicle with insulator,

shown in Figure 26, in place and original shims in-

stalled at top dash mount

2.
Install the three bolts at top mount and four bolts at

lower dash brace.

3.
Install front crossmember, replacing the four bolts

and nuts removed previously.

4.
Replace engine mount cushion; refer to Section 6.

5.
Install front suspension parts as outlined in Sec-

tion 3. Connect stabilizer link to stabilizer (if so
FINAL POSITION

Fig.
30 - Installing Hood Molding Clip

equipped) and connect tie rod end to steering arm as

outlined in Section 9.

6. Install radiator support and fender assembly as out-

lined in this section. Install grille (Section 13).

7.
If left skirt was removed, proceed as follows:

a. Install steering gear. Carefully follow outline

under Steering Gear - Installation in Section 9.

Do not fail to perform adjustments listed under

Mast Jacket Installation in that section.

b.
Install clutch cordon shaft (if so equipped).

c. Install power steering hose clamp (if so equipped).

8. Install brake lines and bleed brakes as outlined in

Section 5.

9. Install hood and adjust as outlined in this section.

10.
Perform following checks and adjustments:

a. Check and adjust front body section alignment

as outlined in Fisher Body Service Manual.

Fig.
29 - Installing Tool J-9559 in Nev/Spring
Fig.
31 - Removing Front End Assembly from Vehicle

CHEVROLET CHASSIS SERVICE MANUAL

5.

6.

7.

8.
2.
Install all fender mounting screws, replacing original

shimming. Refer to removal procedure for screw

location.

3.
Install hydraulic lines at main cylinder and right

hand skirt. Install fuel line at right hand skirt.

4.
Install steering gear as outlined in Section 9. Do

not fail to perform adjustment procedure listed under

Mast Jacket - Installation.

CAMARO

INDEX

Page

General Description 20

Maintenance and Adjustments 20

Hood / . 20

Hinge 20

Bumpers ' . . . 20

Catch Assembly 21

Lock . 21

Fenders 21

Sheet Metal 22
CHASSIS SHEET METAL 11-19

Install pitman arm as outlined in Section 9 under

Maintenance and Adjustments - Steering Gear Ad-

justments.

Remove jack stands and jack.

Bleed brakes as outlined in Section 5.

Perform body alignment as outlined in Fisher Body

Service Manual.

Page

Component Part Replacement . 22

Battery Tray 22

Radiator Support 22

Fender and Skirt Assembly 22

Hood Assembly . 22

Lock and Catch Assembly 22

Trim and Insulation . . . 24

Cowl Vent Grille . . 24

Fig.
32 - Front End Sheet Metal - Camaro

1.
Fender

2.
Hood Hinge

3. Hood

4.
Cowl Vent Grille
5. Trim

6. Molding

7. Fender Extension

8. Bumper Bracket
9. Valance Pane!

10.
Header Panel

11.
Radiator Support

12.
Radiator
13.

14.

15.
Shroud

Hood Lock

Radiator Cap
16.

17.

18.
Bracket (V-8

Hood Catch

Brace
Engine
Only)
19.

20.

21.
Skirt

Seal

Battery
Tray

CHEVROLET CHASSIS SERVICE MANUAL

CHASSIS SHEET METAL 11-20

GENERAL DESCRIPTION

The Camaro sheet metal components are much the

same as other Chevrolet passenger models as shown in

Figure 32. The front end design is such that servicing

of the fenders and skirts is most efficiently performed
by removing the fender and skirt as an assembly. Refer

to Section 14 for bumper service procedures, Section 13

for radiator and grille, and Section 1A for air condition-

ing components.

MAINTENANCE AND ADJUSTMENTS

HOOD ADJUSTMENT

The Camaro hood is adjusted in the conventional man-

ner, by adjustment of the hood bumpers and hinges. The

two hood bumpers are located on each side at the top of

the radiator support. Do not attempt hood latch adjust-

ments until the hinges and bumpers are correctly ad-

justed. Latch adjustments are made so that effort re-

quired to open and close the hood is reasonable, and

hood alignment obtained by hinge and bumper adjust-

ment is maintained when the hood is closed. Note that

the hood latch is not designed to correct basic hood mis-

alignment.

HOOD HINGE (Fig. 33)

NOTE: The body mounted portion of the hood

hinges are slotted to provide up and down move-

ment. The hood mounted end is slotted to pro-

vide forward and rearward movement.

1.
Scribe a. line around the entire. hinge plate to be

repositioned.

2.
Loosen the appropriate screws and shift the position

of the hood into correct alignment using the scribe

marks to check amount of movement. Check align-

ment by tightening screws and closing the hood.

HOOD BUMPERS

Adjust hood bumpers so that hood top surface is flush

with fender and header panel top surfaces. See Figure

34 for correct sheet metal adjustment dimensions.

HOOD CATCH AND LOCK (Fig. 35)

Adjust hood lock bolt so that top surface of hood is

flush with top surface'of header panel. The distance that

the lock bolt protrudes out of the lock plate should be

adjusted so that the hood bumpers are slightly com-

pressed by the fully latched hood, and effort required

to release the hood catch is reasonable. Close the hood

and insure catch engages securely.

FENDERS

Fenders are adjustable with shims at the cowl and

rocker panel. To add or remove shims, loosen bolts
Fig. 33 - Hood Hinge - Camaro

at shim locations (fig. 36) and carefully apply force with

pry bar to provide clearance for shim removal or in-

stallation.

SHEET METAL

For proper operation of doors and hood, and for pre-

sentable appearance, adjust front sheet metal to the di-

mensions shown in Figure 34.

COMPONENT PART REPLACEMENT

NOTE: When replacing sheet metal compo-

nents on Camaro, note position and attachment

of all seals and dust shielding and replace if

necessary.

BATTERY TRAY

Removal

1.
Disconnect battery cables and remove battery from

vehicle.

2.
Remove screws securing battery tray to fender skirt

and radiator support.

3.
Remove battery tray from vehicle.
Installation

Install battery tray following removal procedure in

reverse order.

RADIATOR SUPPORT

Removal

1.
Raise hood, disconnect battery cables, and remove

battery.

2.
Remove front bumper (Section 14).

3.
Remove grille and related components (Section 13).

4.
Disconnect horns, horn relay, voltage regulator,

CHEVROLET CHASSIS SERVICE MANUAL

CHASSIS SHEET METAL 11-22

wiring harness, and washer bottle from radiator

support.

5.
Remove screw connecting battery tray to radiator

support.

6. Remove shroud from vehicle if so equipped.

7.
Remove shroud and radiator (Section 13).

8. Remove screws securing support to frame, skirts,

and fenders.

9. Remove radiator support from vehicle.

Installation

Install radiator support following the removal pro-

cedure in reverse order. Refer to torque specifications

in rear of manual for correct torque values for radiator

supportj grille, and bumper.

FENDER AND SKIRT ASSEMBLY

Removal

1.
Remove front bumper (Section 14).

2.
Remove hood and hood.hinges (two men).

3.
Remove bolts securing brace to skirt and dash panel

and remove brace (fig. 32).

4.
Disconnect any components attached to fender and

skirt such as cruise control, hoses, electrical har-

ness etc.

5.
Remove screws securing radiator support to fender

and skirt.

6. Remove headlamp bezel and headlamp.

7.
Remove screws securing fender and skirt assembly

to header panel, headlamp housing and valance panel.

Remove screw securing fender extension to valance

panel.

8. Remove screws securing fender and skirt assembly

to vehicle and remove fender and skirt assembly.

9. If necessary, remove screws attaching fender ex-

tension and bumper bracket to fender and remove

extension and bracket. Replace fender trim if nec-

essary.

Installation

Install fender anci skirt assembly following the removal

procedure in reverse order. Refer to torque specifi-

cations in rear of manual for correct torque values.

HOOD ASSEMBLY

Procedures for hood removal and installation for

Camaro are the same as for Chevrolet and Chevelle.

Refer to Chevrolet and Chevelle hood removal and in-

stallation procedures, Figure 35 for Camaro hood catch,

support, and lock plate, and Figure 37 for Camaro hood

and insulator.

HOOD CATCH AND LOCK (Fig. 35)

Removal

1.
Remove catch plate assembly by removing screws

retaining catch to header panel, center support, and

radiator support.

NOTE: Before removing hood lock plate from

hood, locate position on hood by scribing around

base of lock plate.

2.
Remove lock plate by removing screws retaining lock

plate to hood and remove lock plate.
Fig.
35 - Hood Catch, Support, and Lock Plate - Camaro

Installation

Install lock and catch plate following the removal pro-

cedure in reverse order. Refer to torque specifications

in rear of manual for correct torque values. Adjust lock

and catch plate as outlined under adjustment procedure

in this section.

HOOD TRIM AND INSULATION (Fig. 37}

. Figure 37 shows the installation details of the Camaro

hood ornament and insulation pad. The insulation and

ornament retainers and nuts are accessible from under

the raised hood.

COWL VENT GRILLE

.Procedures'for Camaro cowl vent grille replacement

are the same as for Chevrolet and Chevelle. Refer to

Chevrolet and Chevelle cowl vent grille replacement.

CHEVROLET CHASSIS SERVICE MANUAL

SECTION 12

ELECTRICAL-BODY AND CHASSIS

CONTENTS
OF
THIS
SECTION

Page
Page

System 12-1

Instruments and Gauges 12-21

Directional Signal 12r40
Windshield Wipers and Washers 12-44

Wiring Diagrams 12-56

Special Tools 12-60

LIGHTING SYSTEM

INDEX

Page

General Description
!2-i

Maintenance and Adjustments
•.................. 12-2

Headlamp Adjustment......................
12-3

Headlamp Panel Travel Adjustment.
12-5

Service Operations.
. . .. 12-5

Front Lighting
12-5

Headlamp
. 12_5

Parking Lamp
12-5

Fender Lamp
. 12_^

Headlamp Panel
12-8

Headlamp Panel Motor
^2-9

Rear Lighting
l2-10

Tail, Stop and Directional Lamps
12-10
Page

Backing Lamps
12-14

License Plate Lamp
12-14

Automatic Transmission Quadrant Lamp
12-14

Seat Separator Console Lamps
. 12-15

Lighting Switch
. . 12-15

Wiper Switch.
12-15

Stoplight Switch
12-15

Dimmer Switch
12-15

Backing Lamp Switches
12-15

Neutral Safety Switches
12-17

Parking Brake Alarm Switch
................. 12-19

Instrument Panel Compartment Lamp/Switch
12-19

Cirgarette Lighter
12-19

GENERAL DESCRIPTION

.
The lighting system includes: the main lighting switch,

stop light, dimmer, and backing lamp switches, head-

lamps, parking lamps, stop, tail and directional lamps,

instrument illumination and indicator lamps, and the

necessary wiring to complete the various circuits. A

fuse panel provides convenient power take offs and fuse

clips for the appropriate circuits (fig. 1).

Chevrolet and Chevelle headlamp installation is all

new in that the headlamps are located in the radiator

support with adjusting screws and springs. Eliminating

the need for having separate headlamp housings. Chev-

rolet and Chevelle headlamp retainers and springs are

interchangeable.

Chevy n headlamp housings are new because of revised

front end styling and Corvette front end lighting is basi-

cally carryover.

Front fender lamps have been added as an option for

Chevrolet models and as standard equipment on Caprice

series.

Camaro models use single headlamps and the Rally

Sport model headlamps are covered by a retractable

section of the grille when lamps are not used. The sec-

tion of the grille covering the headlamps folds back when

lights are required; the headlamps are stationary. The

covering is retracted by a small electric motor mounted

to the headlamp housing. The headlamps are automat-

ically uncovered when the headlight switch is pulled "ON"

for illumination. If at any time the electrical circuit

becomes inoperative, the lamps can be uncovered manu-

ally. The ignition switch must be
"ON"
in order to close

the headlamp doors.

Parking lamp for Chevelle and Chevrolet models are
new due to revised front end sheet metal and bumper

styling. Parking lamps are located in the bumper on

Chevrolet, Chevelle and Chevy n models

Camaro parking lamps are located in the radiator

grille except for the Rally Sport models on which the

parking lamps are in the valance panel. For styling

reasons, the lens is white and an amber glass bulb is

used. All Camaro parking lamps require a separate

ground wire to assure a good ground contact because of

the plastic grille and painted contact surfaces.

The Chevrolet tail, stop, and directional lamps are in

one housing with a three section lens design on Impala

and Caprice sedans. The center lens for Impala series

is the back-up lamp. The center lens on the Caprice is

a tail lamp with the back-up lamps being located in the

rear bumper. Chevrolet station wagons have three indi-

vidual housings with three lenses, the center lamp being

the back-up. Biscayne and Bel-Air sedans have a single

housing and lens for tail, stop, and directional lamp with

a similarly constructed back-up lamp inboard and adja-

cent to it.

Chevelle tail, stop, and directional lamps are a single

lens design that follows through with the rear fender

styling. The back-up lamp is located in r.ear bumper.

Camaro models except Rally Sport have tail lamps

with integral back-up lamps mounted inboard of the rear

fenders between the trunk opening and bumper. The

Rally Sport model has dual tail lamps in the rear housing

and valance mounted back-up lamps.

Corvette, Chevy n, and Corvair tail and directional

signal lights are carryover. The Corvette has new back-

up lamps center mounted above the license plate opening.

CHEVROLET CHASSIS SERVICE

ELECTRICAL-BODY AND CHASSIS 12-3

Fig.
2 - T-3 Safety Aimer

wearing away the insulation due to vibration.

By referring to the wiring diagrams, circuits may be

tested for continuous circuit or shorts with a conventional

test lamp or low reading volt meter.

HEADLAMP ADJUSTMENT-

T-3 HEADLAMPS

CAUTION: Check and tighten radiator support

grille retaining bolts prior to attempting head-

lamp aiming. Distorted grille or supports in

this area will hinder proper aiming of head-

lamps. On Corvette models make sure head-

lamp panel is adjusted properly - refer to

"Headlamp Panel Travel Adjustment".

When aiming headlamps, vehicle should be filled to ca-

pacity with gas, oil, and water but no load. Tires should

be uniformly inflated to recommended pressure.

the T-3 Safety Aimer-Type B (fig. 2), is used for the

headlamp aiming description that follows. An adapter is

required with the Type B T-3 Aimer when adjusting the 7

inch headlamp used on the Chevy n vehicle.

1.
Drive vehicle onto selected aiming area. Bounce

vehicle several times and allow to settle.

2.
Remove headlamp bezels.

3.
Mount the T-3 Aimers on either the No. 1 or No. 2

pair of headlamps so that "the points of the headlamps

engage the smooth inner ring of the aimers.
HORIZONTAL

AIMING

SCREW

STRING OVER

"2R" ON AIMER ARM

Fig.
4—-Headlamp Horizontal Adjustment

NOTE:
In the dual headlamp installation, the

inboard unit is designated No. 1 and the outboard

unit is designated No. 2.

4.
Secure the aimers to the headlamp units by firmly

pressing knob at center of each aimer (fig. 3). Ro-

tate crossarms inboard to approximate horizontal

position.

NOTE:
Moisten suction cups slightly to obtain

maximum holding force.

5. With both aimers in place, knot both ends of elastic

string and, using slots provided, fasten string across

horizontal crossarms of each aimer.

6. Rotate both aimers so that the string just clears the

points on the crossarms.

HORIZONTAL ADJUSTMENT

7. a. Turn horizontal aiming screw, Figure 4, on left-

VERTICAL ADJUSTMENT SCREW

Fig.
3 - Installing Aimer on Headlamp Unit
Fig.
5 - Headlamp Vertical Adjustment

CHEVROLET CHASSIS SERVICE MANUAL