ignition CHEVROLET CITY EXPRESS 2018 Service Manual

Chevrolet City Express Owner Manual (GMNA-Localizing-U.S./Canada-
11683523) - 2018 - CRC - 7/10/17
130 Climate Controls
1:This mode clears the
windshield of fog or frost more
quickly. Air is directed to the
windshield and side window outlets.
Do not drive the vehicle until all
windows are clear.
In defrost or defog mode, excessive
air conditioning use can cause the
windows to fog. If this happens,
change the air delivery mode to
Y
and reduce the fan speed.
Move the air intake control to
%
orMto select the outside air or
recirculation modes.
%: This mode pulls outside air
inside the vehicle.
M: This mode recirculates and
helps to quickly cool the air inside
the vehicle. It can be used to reduce
the outside air and odors that may
enter the vehicle.
Using the recirculation mode for
extended periods may cause the
windows to fog. If this happens,
select the defrost mode. To allow outside air to enter in these
conditions, move the air intake
control to
%.
A/C : Turn the fan control to the
desired speed and press A/C . The
air conditioning does not operate
when the fan control knob is in the
off position. Press A/C to turn the air
conditioning on and off. When A/C
is pressed, an indicator light comes
on to show that the air conditioning
is on.
For quick cool down on hot days:
1. Open the windows to let hot air escape.
2. Move the air intake control to
M.
3. Press A/C .
4. Select the coolest temperature.
5. Select the highest
Aspeed.
Using these settings together for
long periods of time may cause the
air inside the vehicle to become too
dry. To prevent this from happening, after the air in the vehicle has
cooled, move the air intake control
to
%
Rear Window Defogger and
Heated Outside Mirrors
N:
If equipped, press to turn
the rear window defogger on or off.
An indicator light comes on in the
display to show that the feature is
on. This helps to clear frost from the
rear window and outside mirrors.
The ignition must be on for the
defogger to work.
The rear window defogger can be
turned off by pressing
1again or
by turning the ignition to ACC/
ACCESSORY or LOCK.
M: If equipped, press to turn on
or off. An indicator light comes on in
the display to show that the feature
is on. This helps to clear fog or frost
from the surface of the mirror. The
ignition must be in the ON position
for the heated outside mirrors
to work.

Chevrolet City Express Owner Manual (GMNA-Localizing-U.S./Canada-
11683523) - 2018 - CRC - 7/10/17
Driving and Operating 133
Driving and
Operating
Driving Information
Distracted Driving . . . . . . . . . . . . 134
Defensive Driving . . . . . . . . . . . . . 134
Drunk Driving . . . . . . . . . . . . . . . . . 135
Control of a Vehicle . . . . . . . . . . . 135
Braking . . . . . . . . . . . . . . . . . . . . . . . 135
Steering . . . . . . . . . . . . . . . . . . . . . . 135
Off-Road Recovery . . . . . . . . . . . 136
Loss of Control . . . . . . . . . . . . . . . 136
Driving on Wet Roads . . . . . . . . 137
Hill and Mountain Roads . . . . . 138
Winter Driving . . . . . . . . . . . . . . . . 138
If the Vehicle Is Stuck . . . . . . . . 140
Vehicle Load Limits . . . . . . . . . . . 140
Starting and Operating
New Vehicle Break-In . . . . . . . . . 144
Ignition Positions . . . . . . . . . . . . . 145
Starting the Engine . . . . . . . . . . . 146
Engine Heater . . . . . . . . . . . . . . . . 147
Parking over ThingsThat Burn . . . . . . . . . . . . . . . . . . . 149
Engine Exhaust
Engine Exhaust . . . . . . . . . . . . . . 149 Running the Vehicle While
Parked . . . . . . . . . . . . . . . . . . . . . . 150
Automatic Transmission
Continuously VariableTransmission (CVT) . . . . . . . . . 150
Brakes
Antilock BrakeSystem (ABS) . . . . . . . . . . . . . . . 155
Parking Brake . . . . . . . . . . . . . . . . 156
Hill Start Assist (HSA) . . . . . . . . 157
Ride Control Systems
Traction Control/Electronic Stability Control . . . . . . . . . . . . . 158
Cruise Control
Cruise Control . . . . . . . . . . . . . . . . 161
Driver Assistance Systems
Rear Vision Camera (RVC) . . . 163
Parking Assist . . . . . . . . . . . . . . . . 169
Fuel
Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . 170
California FuelRequirements . . . . . . . . . . . . . . . 171
Fuels in Foreign Countries . . . 171
Fuel Additives . . . . . . . . . . . . . . . . 171
Filling the Tank . . . . . . . . . . . . . . . 172 Filling a Portable Fuel
Container . . . . . . . . . . . . . . . . . . . 173
Trailer Towing
General TowingInformation . . . . . . . . . . . . . . . . . . 174
Conversions and Add-Ons
Add-On ElectricalEquipment . . . . . . . . . . . . . . . . . . 174

Chevrolet City Express Owner Manual (GMNA-Localizing-U.S./Canada-
11683523) - 2018 - CRC - 7/10/17
138 Driving and Operating
There is no hard and fast rule about
hydroplaning. The best advice is to
slow down when the road is wet.
Other Rainy Weather Tips
Besides slowing down, other wet
weather driving tips include:
.Allow extra following distance.
. Pass with caution.
. Keep windshield wiping
equipment in good shape.
. Keep the windshield washer fluid
reservoir filled.
. Have good tires with proper
tread depth. See Tires0200.
. Turn off cruise control.
Hill and Mountain Roads
Driving on steep hills or through
mountains is different than driving
on flat or rolling terrain. Tips include:
.
Keep the vehicle serviced and in
good shape.
. Check all fluid levels and brakes,
tires, cooling system, and
transmission. .
Shift to a lower gear when going
down steep or long hills.
{Warning
Using the brakes to slow the
vehicle on a long downhill slope
can cause brake overheating, can
reduce brake performance, and
could result in a loss of braking.
Shift the transmission to a lower
gear to let the engine assist the
brakes on a steep downhill slope.
{Warning
Coasting downhill in N (Neutral)
or with the ignition off is
dangerous. This can cause
overheating of the brakes and
loss of steering assist. Always
have the engine running and the
vehicle in gear. .
Drive at speeds that keep the
vehicle in its own lane. Do not
swing wide or cross the
center line.
. Be alert on top of hills;
something could be in your lane
(e.g., stalled car, accident).
. Pay attention to special road
signs (e.g., falling rocks area,
winding roads, long grades,
passing or no-passing zones)
and take appropriate action.
Winter Driving
Driving on Snow or Ice
Snow or ice between the tires and
the road creates less traction or
grip, so drive carefully. Wet ice can
occur at about 0 °C (32 °F) when
freezing rain begins to fall. Avoid
driving on wet ice or in freezing rain
until roads can be treated.
For Slippery Road Driving:
.Accelerate gently. Accelerating
too quickly causes the wheels to
spin and makes the surface
under the tires slick.

Chevrolet City Express Owner Manual (GMNA-Localizing-U.S./Canada-
11683523) - 2018 - CRC - 7/10/17
Driving and Operating 145
Caution (Continued)
premature wear and earlier
replacement. Follow this
breaking-in guideline every
time you get new brake
linings.
Following break-in, engine speed
and load can be gradually
increased.
Ignition Positions
The ignition lock is designed so that
the ignition switch cannot be turned
to the LOCK position until the shift
lever is moved to the P (Park)
position.
. When placing the ignition switch
in the LOCK position, make sure
that the shift lever is in the
P (Park) position.
. When removing the key from the
ignition switch (if it is inserted),
make sure that the shift lever is
in the P (Park) position.
When the ignition switch cannot be
placed to the LOCK position: 1. Shift the shift lever to the P (Park) position.
2. Move the ignition switch slightly in the ON direction.
3. Turn the ignition switch to the LOCK position.
4. Remove the key if it is inserted in the ignition switch.{Warning
Turning off the vehicle while
moving may cause loss of power
assist in the brake and steering
systems and disable the airbags.
While driving, only shut the
vehicle off in an emergency.
If the ignition switch is placed to the
LOCK position, the shift lever
cannot be moved from the P (Park)
position.
The shift lever can be moved if the
ignition switch is in the ON position
and the brake pedal is pressed.
There is an OFF position between
the LOCK and ACC positions. The
OFF position is indicated by a “1”on
the key cylinder.
Caution
Using a tool to force the key to
turn in the ignition could cause
damage to the switch or break the
(Continued)

Chevrolet City Express Owner Manual (GMNA-Localizing-U.S./Canada-
11683523) - 2018 - CRC - 7/10/17
146 Driving and Operating
Caution (Continued)
key. Use the correct key, make
sure it is all the way in, and turn it
only with your hand. If the key
cannot be turned by hand, see
your dealer.
Ignition Switch Positions
LOCK (0) : Normal parking position.
OFF (1) : The engine can be turned
off without locking the steering
wheel.
ACC (2) : Accessories. This position
activates electrical accessories such
as the radio when the engine is not
running.
ON (3) : Normal operating position.
This position turns on the ignition
system and the electrical
accessories.
START (4) : This position starts the
engine. As soon as the engine has
started, release the key.
It automatically returns to the ON
position.
Starting the Engine
To place the transmission in the
proper gear:
Move the shift lever to P (Park) or
N (Neutral). The engine will not start
in any other position. To restart the
engine when the vehicle is already
moving, use N (Neutral) only.
Caution
If you add electrical parts or
accessories, you could change
the way the engine operates. Any
resulting damage would not be
covered by the vehicle warranty.
See Add-On Electrical Equipment
0 174.
Caution
Do not try to shift to P (Park) if the
vehicle is moving. If you do, you
could damage the transmission.
Shift to P (Park) only when the
vehicle is stopped. Starting Procedure
1. Apply the parking brake.
2. Move the shift lever to P (Park) or N (Neutral). P (Park) is
recommended.
The shift lever cannot be
moved out of P (Park) and into
any of the other gear positions
if the ignition switch is turned to
the OFF position or if the key is
removed from the ignition
switch.
The starter is designed not to
operate if the shift lever is in
any of the driving positions.
3. Crank the engine with your foot off the accelerator pedalby
placing the ignition switch in
the START position. Release
the key when the engine starts.
If the engine starts, but fails to
run, repeat the above
procedure.
.If the engine is very hard to
start in extremely cold
weather or when restarting,
press the accelerator pedal

Chevrolet City Express Owner Manual (GMNA-Localizing-U.S./Canada-
11683523) - 2018 - CRC - 7/10/17
Driving and Operating 147
a little (approximately 1/3 to
the floor) and hold it and
then crank the engine.
Release the key and the
accelerator pedal when the
engine starts.
. If the engine is very hard to
start because it is flooded,
press the accelerator pedal
all the way to the floor and
hold it. Crank the engine for
five to six seconds.
After cranking the engine,
release the accelerator
pedal. Crank the engine
with your foot off the
accelerator pedal by turning
the ignition key to START.
Release the key when the
engine starts. If the engine
starts, but fails to run,
repeat the above
procedure.Caution
Do not operate the starter for
more than 15 seconds at a time.
If the engine does not start, turn
the key off and wait 10 seconds
before cranking again, otherwise
the starter could be damaged.
4. Allow the engine to idle for at least 30 seconds after starting.
Do not race the engine while
warming it up. Drive at
moderate speed for a short
distance first, especially in cold
weather.
In cold weather, keep the
engine running for a minimum
of two to three minutes before
shutting it off. Starting and
stopping the engine over a
short period of time may make
the vehicle more difficult to
start.
Avoid situations that can lead to
potential battery discharge and
potential no-start conditions
such as: .
Installation or extended use of
electronic accessories that
consume battery power when
the engine is not running (phone
chargers, GPS, DVD
players, etc.).
. Vehicle is not driven regularly
and/or only driven short
distances. In these cases, the
battery may need to be charged
to maintain battery life.
Engine Heater
If equipped, the engine coolant
heater can provide easier starting in
cold weather conditions at or below
−7 °C (20 °F). The engine coolant
heater should be plugged in at least
two hours before starting.
To Use the Engine Heater
1. Turn off the engine.
2. Open the hood and unwrap the
electrical cord. The cord is in
the engine compartment, on
the passenger side.

Chevrolet City Express Owner Manual (GMNA-Localizing-U.S./Canada-
11683523) - 2018 - CRC - 7/10/17
Driving and Operating 151
The Continuously Variable
Transmission (CVT) in your vehicle
is electronically controlled to
produce maximum power and
smooth operation.
The recommended operating
procedures for this transmission are
shown on the following pages.
Follow these procedures for
maximum vehicle performance and
driving enjoyment.
Engine power may be automatically
reduced to protect the CVT if the
engine speed increases quickly
when driving on slippery roads or
while being tested on some
dynamometers.
Starting the Vehicle1. After starting the engine, fully press the brake pedal before
moving the shift lever out of the
P (Park) position.
2. Keep the brake pedal pressed and move the shift lever into a
driving gear. 3. Release the brake, then
gradually start the vehicle in
motion.
4. Stop the vehicle completely before moving the shift lever
into the P (Park) position.
The CVT is designed so the brake
pedal MUST be pressed before
shifting from P (Park) to any drive
position while the ignition switch is
in the ON position.
The shift lever cannot be moved out
of P (Park) and into any of the other
gear positions if the ignition switch
is placed in the LOCK, OFF or ACC
position or if the key is removed.
Shifting
After starting the engine, fully press
the brake pedal and move the shift
lever from P (Park) to any of the
desired shift positions.
{Warning
Apply the parking brake if the shift
lever is in any position while the
engine is not running. Failure to
do so could cause the vehicle to
move unexpectedly or roll away
and result in serious personal
injury or property damage.

Chevrolet City Express Owner Manual (GMNA-Localizing-U.S./Canada-
11683523) - 2018 - CRC - 7/10/17
152 Driving and Operating
If the ignition switch is placed in the
OFF or ACC position for any reason
while the vehicle is in N (Neutral),
or any drive position, the key cannot
be turned to the LOCK position and
be removed from the ignition switch.
If this occurs:1. Apply the parking brake when the vehicle is stopped.
2. Move the shift lever to P (Park) to park the vehicle and place
the ignition switch in the LOCK
position to remove the key.
Caution
To prevent transmission damage,
use the P (Park) or R (Reverse)
position only when the vehicle is
completely stopped.
P (Park) : Use the P (Park) shift
lever position when the vehicle is
parked or when starting the engine.
Make sure the vehicle is completely
stopped. The brake pedal must be
pressed and the shift lever button
pushed in to move the shift lever from N (Neutral) or any drive
position to P (Park). Apply the
parking brake. When parking on a
hill, apply the parking brake first,
then place the shift lever into the
P (Park) position.
Caution
To prevent transmission damage,
use the P (Park) or R (Reverse)
position only when the vehicle is
completely stopped.
R (Reverse) : Use the R (Reverse)
position to back up. Make sure the
vehicle is completely stopped before
selecting the R (Reverse) position.
R (Reverse) speed is limited to 30
MPH (48 km/h). Do not exceed 30
MPH (48 km/h) in the R (Reverse)
position. The brake pedal must be
pressed and the shift lever button
pushed in to move the shift lever
from P (Park), N (Neutral), or any
drive position to R (Reverse). N (Neutral) :
Neither forward nor
reverse gear is engaged. The
engine can be started in this
position. You may shift to
N (Neutral) and restart a stalled
engine while the vehicle is moving.
D (Drive) : Use this position for all
normal forward driving.
L (Low) : Use this position for
engine braking on steep downhill
gradients/climbing steep slopes and
whenever approaching sharp bends.
Do not use the L (Low) position in
any other circumstances.
Engine power may be automatically
reduced to protect the CVT if the
engine speed increases quickly
when driving on slippery roads or
while being tested on some
dynamometers.

Chevrolet City Express Owner Manual (GMNA-Localizing-U.S./Canada-
11683523) - 2018 - CRC - 7/10/17
Driving and Operating 153
Shift Lock Release
If the battery is discharged, the shift
lever may not be moved from the
P (Park) position even with the
brake pedal pressed.
To move the shift lever:1. Place the ignition switch to the LOCK position and remove
the key.
2. Apply the parking brake. 3. Remove the shift lock release
cover using a suitable tool.
4. Push down the shift lock release using a suitable tool.
5. Push the shift lever button and move the shift lever to the
N (Neutral) position while
holding down the shift lock
release.
Place the ignition switch in the ON
position to unlock the steering
wheel. The vehicle may be moved
to the desired location.
Replace the removed shift lock
release cover after the operation.
If the shift lever cannot be moved
out of the P (Park) position, have a
dealer check the CVT system as
soon as possible.
Overdrive (O/D) OFF Switch
When the O/D OFF switch is
pressed with the shift lever in the
D (Drive) position, the light in the
instrument panel illuminates. See
Overdrive Off Light 094.
Use the Overdrive off mode when
you need improved engine braking.
To turn off the Overdrive off mode,
press the O/D OFF switch again.
The indicator light will turn off.

Chevrolet City Express Owner Manual (GMNA-Localizing-U.S./Canada-
11683523) - 2018 - CRC - 7/10/17
154 Driving and Operating
Each time the engine is started,
or when the shift lever is shifted to
any position other than D (Drive),
the Overdrive off mode will be
automatically turned off.
Accelerator Downshift in D
Position
For passing or hill climbing, press
the accelerator pedal to the floor.
This shifts the transmission down
into a lower gear, depending on the
vehicle speed.
High Fluid Temperature
Protection Mode
If the fluid temperature becomes too
high from climbing a steep grade in
high temperatures, such as towing a
trailer. Engine power and vehicle
speed will be decreased
automatically to reduce the chance
of transmission damage. Vehicle
speed can be controlled with the
accelerator pedal but the engine
and vehicle speed may be limited.Fail Safe
When the fail-safe operation occurs,
the CVT will not be shifted into the
selected driving position.
If the vehicle is driven under
extreme conditions, such as
excessive wheel spinning and
subsequent hard braking, the
fail-safe system may be activated.
The malfunction indicator lamp may
come on to indicate the fail-safe
mode is activated. See
Malfunction
Indicator Lamp (Check Engine
Light) 091. This will occur even if all
electrical circuits are functioning
properly. In this case, place the
ignition switch in the OFF position
and wait for 10 seconds. Then place
the ignition switch back in the ON
position. The vehicle should return
to its normal operating condition. If it
does not return to its normal
operating condition, have a dealer
check the transmission and repair if
necessary.
{Warning
When the high fluid temperature
protection mode or fail-safe
operation occurs, vehicle speed
may be gradually reduced. The
reduced speed may be lower than
other traffic, which could increase
the chance of a collision. Be
especially careful when driving.
If necessary, pull to the side of
the road at a safe place and allow
the transmission to return to
normal operation, or have it
repaired if necessary.