jump start CHRYSLER CARAVAN 2000 User Guide

TEST SC-4ACHECKING SPEED CONTROL OPERATION
Perform TEST SC-1A Before Proceeding
*Perform Verification TEST VER-3A. **Check connectors - Clean / repair as necessary.
START TEST
SC-4A. TURN IGNITION OFF.
DISCONNECT THE USING AN OHMMETER, REPAIR OPEN IN
CLUTCH PEDAL MEASURE RESISTANCE IS THE RESISTANCE NO CLUTCH PEDAL
SWITCH HARNESS BETWEEN CLUTCH PEDAL BELOW 5.0 OHMS? SWITCH GROUND
CONNECTOR.** SW.CONNECTOR CAVITY CIRCUIT.*
2 AND GROUND. FIG.1
YES
KEY ON. WHILE THE CLUTCH PEDAL CHECK ADJUSTMENT OF
OBSERVING THE DRB, SWITCH HARNESS DID THE DRB CHANGE YES CLUTCH PEDAL SWITCH.
CONNECT A JUMPER CONNECTOR CAVITIES FROM "RELEASED" TO IF ADJUSTMENT IS OK,
WIRE ACROSS... 1 AND 2. "PRESSED"? REPLACE THE CLUTCH
FIG.1 PEDAL SWITCH.*
NO
KEY OFF. USING AN OHMMETER,
DISCONNECT THE ECM MEASURE THE IS THE RESISTANCE NO REPAIR OPEN CLUTCH
HARNESS RESISTANCE OF THE BELOW 5.0 OHMS? PEDAL SWITCH SENSE
CONNECTORS.** CLUTCH PEDAL SWITCH CIRCUIT.*
CIRCUIT. FIG.2
YES
ECM HARNESS REPAIR CLUTCH
USING AN OHMMETER CONNECTOR CAVITY IS THE RESISTANCE NO PEDAL SWITCH SENSE
MEASURE RESISTANCE 46 AND GROUND. ABOVE 5.0 OHMS? CIRCUIT FOR SHORT
BETWEEN... TO GROUND.*
FIG. 1
YES
REPLACE THE ENGINE
CONTROL MODULE.*
S
P
E
E
D
C
O
N
T
R
O
L
T
E
S
T
S
387
ProCarManuals.com

TEST SC-6ACHECKING CRUISE INDICATOR OPERATION
Perform TEST SC-1A Before Proceeding
*Perform Verification TEST VER-3A. **Check connectors - Clean / repair as necessary.
NOTE: PERFORM TEST
START TEST SC-1A TO VERIFY
SC-6A. PROPER CRUISE
SWITCH OPERATION
BEFORE CONTINUING.
TURN IGNITION ON. MONITOR CRUISE DOES LAMP STATE CHECK CRUISE LAMP
WITH THE DRB SELECT LAMP STATE WHILE CHANGE FROM "ON" YES BULB, REPLACE AS
"BODY" "MIC" PRESSING CRUISE TO "OFF" WHEN NECESSARY. IF OK,
"MONITOR DISPLAY" ON/OFF BUTTON PRESSING THE REPLACE THE
THEN "CCD BUS INFO". SEVERAL TIMES. BUTTON? INSTRUMENT CLUSTER.*
NO
KEY OFF. KEY ON. CONNECT A
DISCONNECT THE ECM JUMPER WIRE BETWEEN IS THE SPEED YES REPLACE THE ENGINE
HARNESS ECM HARNESS CONTROL LAMP ON? CONTROL MODULE.*
CONNECTORS.** CONNECTOR CAVITY 30
AND GROUND. FIG.1
NO
KEY OFF. USING AN OHMMETER, REPAIR SHORT TO
DISCONNECT THE BCM MEASURE RESISTANCE IS THE RESISTANCE YES GROUND ON THE
HARNESS BETWEEN ECM HARNESS BELOW 5.0 OHMS? SPEED CONTROL LAMP
CONNECTORS.** CONNECTOR CAVITY 30 CONTROL CIRCUIT.*
AND GROUND. FIG.1
NO
USING AN OHMMETER
MEASURE THE SPEED IS THE RESISTANCE YES REPAIR OPEN SPEED
CONTROL LAMP ABOVE 5.0 OHMS? CONTROL LAMP
CONTROL CIRCUIT. CONTROL CIRCUIT.*
FIG.2
NO
REPLACE THE BODY
CONTROL MODULE.*
S
P
E
E
D
C
O
N
T
R
O
L
T
E
S
T
S
391
ProCarManuals.com

TEST NS-1AREPAIRING A NO CRANK CONDITION
Perform TEST NS-SEL Before Proceeding
*Perform Verification TEST VER-1A. **Check connectors - Clean / repair as necessary.
NOTE: BATTERY MUST
START TEST BE FULLY CHARGED
NS-1A. BEFORE DIAGNOSING
A NO-START
CONDITION.
NOTE: BEFORE VEHICLE THEFT DIAGNOSE
CONTINUING, BE (SKIM) SYSTEM FOR ARE ANY CODES YES TROUBLE CODE
SURE TO CHECK DIAGNOSTIC TROUBLE PRESENT? BEFORE
ENGINE SYSTEM CODES. CONTINUING.]
AND...
NO
INSPECT BATTERY
CABLES FOR IS THERE EVIDENCE YES REPAIR AS
TURN IGNITION OFF. CORROSION, OF PROBLEMS? NECESSARY.*
LOOSENESS OR OTHER
PROBLEMS.
NO
TURN IGNITION OFF. KEY ON. WITH A REPAIR THE STARTER
VOLTMETER, MEASURE IS THE VOLTAGE YES RELAY CONTROL
DISCONNECT THE ECM THE STARTER RELAY ABOVE 1.0 VOLT? CIRCUIT FOR A
HARNESS CONTROL CKT. SHORT TO VOLTAGE.*
CONNECTORS.** FIG.1
NO
KEY OFF. USING A FULLY DEPRESS THE
JUMPER WIRE CONNECT CLUTCH PEDAL. DID THE ENGINE YES REPLACE THE ENGINE
THE STARTER RELAY CRANK? CONTROL MODULE.*
CONTROL CKT TO ATTEMPT TO CRANK
GROUND. FIG.1 THE ENGINE.
NO
WITH A VOLTMETER,
DISCONNECT THE MEASURE THE FUSED IS THE VOLTAGE NO REPAIR OPEN FUSED
STARTER RELAY FROM B(+) CIRCUIT. ABOVE 11.6 VOLTS? BATTERY CIRCUIT.*
THE PDC.**
FIG.1
YES
WARNING: THE TRANS WARNING: THE ENGINE BRIEFLY CONNECT A
MUST BE IN NEUTRAL MAY BE CRANKED IN JUMPER WIRE BETWEEN CONTINUE TEST
AND THE PARKING THE NEXT STEP. KEEP THE STARTER RLY NS-1A ON THE
BRAKE MUST BE ON AWAY FROM MOVING OUTPUT AND FUSED NEXT PAGE.
FOR THE NEXT STEP. ENGINE PARTS. B(+) CKTS. FIG.1
N
O
S
T
A
R
T
T
E
S
T
S
395
ProCarManuals.com

TEST NS-1ACONTINUED - REPAIRING A NO CRANK CONDITION
*Perform Verification TEST VER-1A. **Check connectors - Clean / repair as necessary.
TEST NS-1A
CONTINUED FROM DID THE STARTER YES CONTINUE TEST
THE PREVIOUS MOTOR CRANK THE NS-1A ON THE
PAGE. ENGINE? NEXT PAGE.
NO
DID THE STARTER
YES SOLENOID CLICK NO DISCONNECT THE
WHEN THE JUMPER JUMPER WIRE.
WIRE WAS
CONNECTED?
USING AN OHMMETER, DISCONNECT STARTER
MEASURE THE RELAY OUTPUT WIRE
STARTER RELAY FROM THE STARTER
OUTPUT CIRCUIT. SOLENOID.**
FIG.1 FIG.2
IS THE RESISTANCE NO REPAIR OPEN
BELOW 5.0 OHMS? STARTER RELAY
OUTPUT CKT.*
YES
CHECK THE BATTERY DID EITHER BATTERY
REINSTALL STARTER CABLES FOR HIGH CIRCUIT HAVE A YES REPAIR THE BATTERY
RELAY. RESISTANCE. (USE VOLTAGE DROP CIRCUIT FOR HIGH
SERVICE MANUAL GREATER THAN 0.2 RESISTANCE.*
PROCEDURE) VOLT?
NO
ATTEMPT TO
MANUALLY ROTATE IS THE CRANKSHAFT NO REPAIR ENGINE
THE CRANKSHAFT 360 ABLE TO ROTATE 360 MECHANICAL PROBLEM
DEGREES. DEGREES? AS NECESSARY.*
YES
REPLACE THE
STARTER MOTOR.*
N
O
S
T
A
R
T
T
E
S
T
S
397
ProCarManuals.com

TEST NS-1ACONTINUED - REPAIRING A NO CRANK CONDITION
*Perform Verification TEST VER-1A. **Check connectors - Clean / repair as necessary.
TEST NS-1A KEY OFF. WITH AN IS THE RESISTANCE
CONTINUED FROM OHMMETER, MEASURE BETWEEN NO REPLACE THE
THE PREVIOUS THE STARTER RELAY 60.0 AND 90.0 STARTER RELAY.*
PAGE. TERMINALS 85 AND 86. OHMS?
FIG.1
YES
KEY ON. USING A AT THE ECM HARNESS REPAIR THE STARTER
VOLTMETER, MEASURE CONNECTOR. IS THE VOLTAGE YES RELAY CONTROL CKT
STARTER RELAY ABOVE 1.0 VOLT? FOR A SHORT TO
CONTROL CKT... VOLTAGE.*
FIG.2
NO
WITH AN OHMMETER, BETWEEN THE ECM
MEASURE RESISTANCE HARNESS CONNECTOR IS THE RESISTANCE YES REPAIR THE OPEN
OF THE STARTER AND THE PDC ABOVE 5.0 OHMS? STARTER RELAY
RELAY CONTROLCONTROL CIRCUIT.*
CIRCUIT... FIG.2
NO
KEY ON. USING A WITH THE CLUTCH
VOLTMETER, MEASURE WHILE DEPRESSING DEPRESSED, IS THE YES REPLACE THE
THE CLUTCH THE CLUTCH. VOLTAGE ABOVE 10.0 STARTER RELAY.*
INTERLOCK SWITCH VOLTS?
CKT AT THE PDC)...
NO
KEY OFF. DISCONNECT MEASURE CLUTCH
THE CLUTCH INTERLOCK INTERLOCK SWITCH IS THE VOLTAGE NO REPAIR OPEN CLUTCH
SWITCH HARNESS HARNESS CONNECTOR ABOVE 10.0 VOLTS? INTERLOCK SWITCH
CONNECTOR. KEY ON. CAVITY 1. BATTERY SUPPLY.*
USING A VOLTMETER... FIG.3
YES
CONNECT A JUMPER PROBE THE CLUTCH
WIRE ACROSS THE INTERLOCK SWITCH IS THE VOLTAGE YES ADJUST OR REPLACE
CLUTCH INTERLOCK OUTPUT CKT. IN THE ABOVE 10.0 VOLTS? THE CLUTCH
SWITCH HARNESS PDC. INTERLOCK SWITCH.*
CONNECTOR. FIG.2
NO
REPAIR OPEN
CIRCUIT BETWEEN
STARTER RELAY AND
CLUTCH INTERLOCK
SWITCH.*
N
O
S
T
A
R
T
T
E
S
T
S
399
ProCarManuals.com

TEST NS-2AREPAIRING A NO RESPONSE CONDITION
Perform TEST NS-SEL Before Proceeding
*Perform Verification TEST VER-1A. **Check connectors - Clean / repair as necessary.
START TEST DOES THE VEHICLE YES PERFORM TEST
NS-2A. START? NS-2B.
NO
KEY OFF. WITH AN OHMMETER, IS THE RESISTANCE
MEASURE RESISTANCE ABOVE 5.0 OHMS FOR YES REPAIR THE OPEN
DISCONNECT THE ECM OF THE PCM GND CKTS ANY OF THE ECM GROUND.*
HARNESS AT HARNESS CAVITIES MEASUREMENTS?
CONNECTORS.** 1 AND 27. FIG.1
NO
KEY ON. USING A AT ECM HARNESS REPAIR OPEN OR
VOLTMETER, MEASURE CONNECTOR CAVITY 47. IS THE VOLTAGE NO SHORT TO GROUND IN
THE FUSED IGNITION ABOVE 10.0 VOLTS? THE FUSED IGNITION
SWITCH OUTPUT SWITCH OUTPUT
CIRCUIT... FIG.1 CIRCUIT.*
YES
KEY OFF. USING A VOLTMETER REPAIR OPEN FUSE
REMOVE THE DIESEL PROBE DIESEL POWER IS THE VOLTAGE NO OR FUSED BATTERY
POWER RELAY. RELAY CONNECTOR ABOVE 10.0 VOLTS? CIRCUIT TO DIESEL
CAVITY 30 (IN PDC). POWER RELAY.*
KEY ON. FIG.2
YES
KEY OFF. CONNECT A MEASURE VOLTAGE AT IS THE VOLTAGE
JUMPER WIRE ACROSS ECM HARNESS ABOVE 10.0 VOLTS NO REPAIR OPEN DIESEL
RELAY CONNECTOR CONNECTOR CAVITIES FOR EACH POWER RELAY OUTPUT
CAVATIES 30 AND 87. 2 AND 28. MEASUREMENT? CIRCUIT(S).*
FIG. 1 AND 2
YES
KEY OFF. RECONNECT WITH JUMPER WIRE
THE ENGINE CONTROL STILL CONNECTED, DOES THE VEHICLE NO REPLACE THE ENGINE
MODULE HARNESS ATTEMPT TO START START? CONTROL MODULE.*
CONNECTORS. VEHICLE.
YES
CONTINUE TEST
NS-2A ON THE
NEXT PAGE.
N
O
R
E
S
P
O
N
S
E
T
E
S
T
401
ProCarManuals.com

11.0 REQUIRED TOOLS AND EQUIPMENT
ammeter
DRB (diagnostic read-out box) scan tool
jumper wires and probes
ohmmeter
vacuum gauge
voltmeter
12.0 GLOSSARY OF TERMS
backfire,
popbackfuel ignites in either the intake or the exhaust system
BCMbody control module
cuts out,
missesa steady pulsation or the inability of the engine to maintain a consistent
rpm
DLCdata link connector (previously called ``engine diagnostic connector'')
detonation,
pre-ignitiona mild to severe ping, especially under loaded engine conditions
ECMengine control module
ECTengine coolant temperature sensor
EGRexhaust gas recirculation valve and system
generatorpreviously called ``alternator''
hard startThe engine takes longer than usual to start, even though it is able to
crank normally.
hesitation,
sag, stumbleThere is a momentary lack of response when the throttle is opened.
This can occur at all vehicle speeds. If it is severe enough, the engine
may stall.
IATintake air temperature sensor
lack of power,
sluggishThe engine has less than expected power, with little or no increase in
vehicle speed when the throttle is opened.
MILmalfunction indicator lamp
PDCpower distribution center
poor fuel
economyThere is significantly less fuel mileage than other vehicles of the same
design and configuration.
G
E
N
E
R
A
L
I
N
F
O
R
M
A
T
I
O
N
428
ProCarManuals.com