lock CHRYSLER PT CRUISER 2008 1.G Repair Manual

WARNING!
Tilting the steering column while the vehicle is
moving is dangerous. Without a stable steering col-
umn, you could lose control of the vehicle and have
an accident. Adjust the column only while the ve-
hicle is stopped. Be sure it is locked before driving.ELECTRONIC SPEED CONTROL — IF EQUIPPEDWhen engaged, this device takes over the accelerator
operation at approximately either 30 mph (40 km/h ) or
35 mph (56 km/h) depending on the model or engine
size. The speed control lever is located on the right side of
the steering wheel.
To Activate:Push the ON/OFF button. The CRUISE indicator in the
instrument cluster will illuminate. To turn the system
OFF, push the ON/OFF button a second time. The
CRUISE indicator will turn off. The system should be
turned OFF when not in use.
PT 7 Speed Control Ballon L or R
194 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

has successfully accepted the frequency signal. The
indicator light will flash slowly and then rapidly when
fully trained.
If you unplugged the device for training, plug it back in
at this time.
Then proceed with Step 4 under “Programming
HomeLink” earlier in this section.USING HOMELINKTo operate, simply press and release the programmed
HomeLinkbutton. Activation will now occur for the
trained device (i.e., garage door opener, gate operator,
Security system, entry door lock, home/office lighting,
etc. The hand-held transmitter of the device may also be
used at any time.
REPROGRAMMING A SINGLE HOMELINK 
BUTTONTo re-program a channel that has been previously
trained, follow these steps:
1. Turn the ignition switch to the ON/RUN position.
2. Press and hold the desired HomeLink button until
the indicator light begins to flash after 20 seconds. Do not
release the button.
3. Without releasing the button, proceed with Program-
ming Homelink Step 2 and follow all remaining steps.SECURITYIt is advised to erase all channels before you sell or turn
in your vehicle.
To do this, press and hold the two outside buttons for 20
seconds until the red indicator flashes. Note that all
channels will be erased. Individual channels cannot be
erased.
202 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

WARNING!
•
To avoid tipping, lock the shelf securely in all
positions.
•
Do not drive this vehicle with the liftgate open, or
use the shelf as a seat.
•
Failure to follow these warnings could result in
serious or fatal injury.
Position 1 (Top)Insert the front outboard corners of the shelf panel into
the top guides and slide forward. Press down on the back
of the shelf panel to lock it into place.
WARNING!
Do not load objects on the shelf in position 1 (top). In
an accident objects could strike occupants causing
serious or fatal injury.
Rear Shelf Panel Position 1
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 211
3

Position 2 (Middle)Insert the front outboard corners of the shelf panel into
the middle guides and slide forward. Press down on the
back of the shelf panel to lock it into place.
WARNING!
Do not load objects over 100 lbs (45 kg) in position 2
(middle). Failure to follow this warning could cause
the shelf to collapse resulting in personal injury.Position 3 (Floor)Insert the front outboard corners of the shelf panel into
the bottom guides and slide forward.
NOTE:To carry items that may soil the carpeting, the
rear shelf panel may be inverted in position 2 or position
3.Position 4 (Vertical)Insert the front outboard corners of the shelf panel into
the vertical guides behind the rear seatbacks near the
floor and slide downward. Push the shelf panel forward
to lock it into place.
Rear Shelf Panel Position 2
212 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

WARNING!
When in the vertical position, the rear shelf panel
should not be used as a barrier for large objects in the
cargo area when the seatbacks folded down. In an
accident objects could strike the seatbacks or occu-
pants causing serious or fatal injury.Position 5 (table)With the liftgate open the rear shelf panel can be moved
rearward to act as a serving counter.
1. Install the front corners of the shelf panel into the top
rear guides. Press down on the shelf panel to lock it into
place.
Rear Shelf Panel Position 4
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 213
3

ROOF LUGGAGE RACK — IF EQUIPPEDThe crossbars and siderails are designed to carry the
weight on vehicles equipped with a luggage rack. The
load must not exceed 150 lbs (68 kg), and should be
uniformly distributed over the luggage rack crossbars.
Use both adjustable crossbars assemblies to support the
load and distribute the load as evenly as possible.
To adjust the crossbars with latch-style releases (if
equipped), release the latches on the inboard side of the
crossbar supports on each side of the vehicle, then move
the crossbars to the desired position. Once the crossbar is
in the desired position, return both latches to the locked
position.To adjust the crossbars with bottom-style releases (if
equipped), depress the button and slide the crossbar to
the next locking position. Alternate sides until the cross-
bars are positioned correctly for your cargo and the
stanchions are locked square to the slide rails.
External racks do not increase the total load carrying
capacity of the vehicle. Be sure that the total occupant
and luggage load inside the vehicle, plus the load on the
luggage rack, do not exceed the rated vehicle capacity.
NOTE:
When the luggage rack is not in use, place the
crossbars together at the rear of the vehicle. In this
position they are designed to improve the vehicle aero-
dynamics and reduce wind noise.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 215
3

▫Tire Pressure Monitor (TPM) .............244
▫ Personal Settings (Customer Programmable
Features) ...........................244
 Setting The Analog Clock .................250
 Radio General Information ................250
▫ Radio Broadcast Signals .................250
▫ Two Types Of Signals ..................250
▫ Electrical Disturbances ..................251
▫ AM Reception .......................251
▫ FM Reception ........................251
 Sales Code REF — AM/FM/CD (Single Disc)
Radio With Optional Satellite Radio And Hands
Free Phone Capability ...................251
▫ Operating Instructions - Radio Mode .......252▫
Operating Instructions - CD Mode .........255
▫ Operating Instructions - Auxiliary Mode .....257
▫ Operating Instructions - Hands-Free Phone —
If Equipped .........................258
▫ Operating Instructions - Satellite Radio — If
Equipped ...........................258
 Sales Code RAQ – AM/FM/CD (6-Disc) Radio
With Optional Satellite Radio, Hands-Free Phone,
And Video Entertainment Systems (VES™)
Capabilities ...........................259
▫ Operating Instructions - Radio Mode .......259
▫ Operating Instructions - (CD Mode For CD
Audio Play) .........................265
▫ Load/Eject Button (CD Mode For CD Audio
Play) ..............................266
220 UNDERSTANDING YOUR INSTRUMENT PANEL

INSTRUMENT PANEL FEATURES1 - Air Vent5 - Radio9 - TRAC Off13 - Hazard Lights
2 - Instrument Cluster 6 - Assist Handle10 - Climate Controls14 - Rear Window Defroster*
3 - Power Windows 7 - Glove Compartment 11 - Storage Cubby 15 - Power Convertible Top
4 - Analog Clock 8 - Heated Seats*12 - Pass Airbag Off16 - Side Mirror Control*
* If Equipped
222 UNDERSTANDING YOUR INSTRUMENT PANEL

14. Electronic Stability Program (ESP) Indicator
Light/Traction Control System (TCS) Indicator Light —
If EquippedIf this indicator light flashes during accelera-
tion, apply as little throttle as possible. While
driving, ease up on the accelerator. Adapt your
speed and driving to the prevailing road con-
ditions, and do not switch off the ESP, or TCS — if
equipped.
15. Brake System Warning Light This light monitors various brake functions,
including brake fluid level and parking brake
application. If the brake light turns on, it may
indicate that the parking brake is applied, there
is a low brake fluid level or there is a problem with the
anti-lock brake system. The dual brake system provides a reserve braking capac-
ity in the event of a failure to a portion of the hydraulic
system. Failure of either half of the dual brake system is
indicated by the Brake Warning Light which will turn on
when the brake fluid level in the master cylinder has
dropped below a specified level.
The light will remain on until the cause is corrected.
NOTE:
The light may flash momentarily during sharp
cornering maneuvers which change fluid level condi-
tions. The vehicle should have service performed, and
the brake fluid level checked.
If brake failure is indicated, immediate repair is neces-
sary.
UNDERSTANDING YOUR INSTRUMENT PANEL 231
4

WARNING!
Driving a vehicle with the brake light on is danger-
ous. Part of the brake system may have failed. It will
take longer to stop the vehicle. You could have an
accident. Have the vehicle checked immediately.
Vehicles equipped with Anti-Lock brakes (ABS), are also
equipped with Electronic Brake Force Distribution (EBD).
In the event of an EBD failure, the Brake Warning Light
will turn on along with the ABS Light. Immediate repair
to the ABS system is required.
The operation of the Brake Warning Light can be checked
by turning the ignition switch from the OFF position to
the ON position. The light should illuminate for approxi-
mately two seconds. The light should then turn off unless the parking brake is applied or a brake fault is detected.
If the light does not illuminate, have the light inspected
by an authorized dealer.
The light also will turn on when the parking brake is
applied with the ignition switch in the ON position.
NOTE:
This light shows only that the parking brake is
applied. It does not show the degree of brake application.
16. Seat Belt Reminder Light When the ignition switch is first turned ON, this
light will come on for about six seconds. A chime
will sound if you have not pulled the shoulder belt
out of the retractor. This is a reminder to “buckle up”. If
you do not buckle up, the light will remain on.
17. Engine Temperature Warning Light This light warns of an overheated engine condi-
tion. If the engine is critically hot, a warning chime232 UNDERSTANDING YOUR INSTRUMENT PANEL