headrest CHRYSLER VOYAGER 2005 User Guide

SEAT BACK COVER/FOAM -
SECOND ROW - FOLD-IN-
FLOOR
REMOVAL
(1) Remove both armrest. (Refer to 23 - BODY/
SEATS/ARMREST - REMOVAL).
(2) Remove headrest and headrest sleeves. (Refer
to 23 - BODY/SEATS/HEADREST SLEEVE -
REMOVAL).
(3) Remove seat back panel. (Refer to 23 - BODY/
SEATS/SEAT BACK PANEL - REMOVAL).
(4) Disengage seat back cover J-straps (Fig. 52).
(5) Remove two push pin fasteners attaching seat
back cover at the bottom of seat back.
(6) Remove seat back cover and foam from seat
back frame (Fig. 53).
(7) Separate seat back cover from the foam (Fig.
54).
INSTALLATION
(1) Place the seat back cover and foam together
(Fig. 54) and (Fig. 53).
(2) Place seat back cover/foam on the seat back
frame.
(3) Install two push pin fasteners attaching seat
back cover at the bottom of seat back.
(4) Engage seat back cover J-straps (Fig. 52).
(5) Remove seat back panel. (Refer to 23 - BODY/
SEATS/SEAT BACK PANEL - INSTALLATION)
(6)(7) Install headrest sleeves and headrest. (Refer to
23 - BODY/SEATS/HEADREST SLEEVE - INSTAL-
LATION).
(8) Install both armrest. (Refer to 23 - BODY/
SEATS/ARMREST - INSTALLATION).
Fig. 52 SECOND ROW SEAT BACK
1 - J-STRAPS
Fig. 53 SEAT BACK COVER 1
1 - LOCKING STRIPS
Fig. 54 SEAT BACK FOAM
1 - LOCKING CLIPS
RSSEATS23 - 133

INSTALLATION
(1) Place prop rod into position.
(2) Install lower attaching screw (Fig. 78).
(3) Install prop rod top screw (Fig. 77).
(4) Install lower front shield (Fig. 76).
BUCKET SEAT BACK - QUAD
BUCKET
REMOVAL
NOTE: Quad seats equipped with child restraint
seats have an interlock feature that will not allow
the seat back to fold forward with the child seat
open.
(1) Remove the headrests. (Refer to 23 - BODY/
SEATS/HEADREST - REMOVAL)
(2) Remove the armrests, if equipped. (Refer to 23
- BODY/SEATS/ARMREST - REMOVAL)
(3) Remove the seat back hinge covers. (Refer to
23 - BODY/SEATS/SEAT BACK HINGE COVERS -
QUAD BUCKET, 50/50 SPLIT, BENCH - REMOVAL)
(4) Disconnect the child seat synchronizer cable, if
equipped. (Fig. 79)
(5) Remove the seat back frame bolts and remove
the seat back. (Fig. 80)
Fig. 77 PROP ROD TOP SCREW
1 - ATTACHING SCREW
Fig. 78 PROP RODS
1 - ATTACHING PIN
2 - ATTACHING SCREW
Fig. 79 QUAD SEAT SYNCHRONIZER CABLE
1 - CABLE END CONNECTOR
2 - SYNCHRONIZER CABLE
3 - SEATBACK HINGE
23 - 140 SEATSRS
SEAT PROP ROD - SECOND ROW - FOLD-IN-FLOOR (Continued)

INSTALLATION
(1) Install the seat back.
(2) Install the shoulder bolts attaching the seat
back hinge to the seat back frame and tighten to 48
N´m (35 ft. lbs.) torque.
(3) Connect the child seat synchronizer cable, if
equipped.
(4) Install the seat back hinge covers. (Refer to 23
- BODY/SEATS/SEAT BACK HINGE COVERS -
QUAD BUCKET, 50/50 SPLIT, BENCH - INSTALLA-
TION)
(5) Install the armrests. (Refer to 23 - BODY/
SEATS/ARMREST - INSTALLATION)
(6) Install the headrest. (Refer to 23 - BODY/
SEATS/HEADREST - INSTALLATION)
(7) Verify seat back operation.
QUAD SEAT CUSHION
REMOVAL
(1) Remove the quad bucket seat side shields and
cup holder. (Refer to 23 - BODY/SEATS/SEAT SIDE
SHIELD/QUAD BUCKET SEAT SIDE SHIELD/CUP
HOLDER - REMOVAL) and (Refer to 23 - BODY/
SEATS/QUAD BUCKET SEAT SIDE SHIELD - NO
CUP HOLDER - REMOVAL)
(2) Remove seat track front and rear covers if
equipped. (Refer to 23 - BODY/SEATS/SEAT TRACK
REAR COVER - REMOVAL) and (Refer to 23 -
BODY/SEATS/SEAT TRACK FRONT COVER -
REMOVAL)(3) If equipped, open storage bin to access front
pan bolts.
(4) Remove bolts attaching seat cushion pan to
seat riser.
(5) Disconnect wire connectors, if equipment.
(6) Remove seat cushion from seat.
(7) Disengage J-strap retainers holding seat cover
to cushion.
(8) Remove seat cushion pan from cover and pad.
INSTALLATION
(1) Place seat cushion cover in position on seat
cushion.
(2) Engage J-strap retainers to hold seat cover to
cushion.
(3) Place seat cushion in position on seat.
(4) Connect wire connectors, if equipment.
(5) Install bolts attaching seat cushion to seat
riser. Tighten bolts to 40 N´m (29.5 ft. lbs.) torque.
(6) If equipped, close storage bin.
(7) Install seat track front and rear covers, if
equipped. (Refer to 23 - BODY/SEATS/SEAT TRACK
REAR COVER - INSTALLATION) and (Refer to 23 -
BODY/SEATS/SEAT TRACK FRONT COVER -
INSTALLATION)
(8) Install the quad seat side shield and cup holder
if equipped. (Refer to 23 - BODY/SEATS/QUAD
BUCKET SEAT SIDE SHIELD/CUP HOLDER -
INSTALLATION) and (Refer to 23 - BODY/SEATS/
QUAD BUCKET SEAT SIDE SHIELD - NO CUP
HOLDER - INSTALLATION)
(9) Install seat cushion side covers. (Refer to 23 -
BODY/SEATS/FRONT SEAT CUSHION SIDE
COVER - INSTALLATION)
QUAD BUCKET SEAT SIDE
SHIELD/CUP HOLDER
REMOVAL
(1) Remove the seat from the vehicle. Refer to
Owner's Manual for proper procedures.
(2) Remove the two screws and remove the hinge
cover (Fig. 81)
(3) Remove the dump latch handle.
(4) Remove the three screws (Fig. 82).
(5) Depress the tab on the cup holder assembly
(Fig. 83).
(6) Using a deep well socket or equivalent, depress
the push pin tabs and remove the cup holder assem-
bly (Fig. 84).
Fig. 80 SEAT BACK HINGE - TYPICAL
1 - SEATBACK FRAME SHOULDER BOLTS
2 - SEAT CUSHION FRAME BOLTS
3 - SEATBACK HINGE
RSSEATS23 - 141
BUCKET SEAT BACK - QUAD BUCKET (Continued)

(7) Install bench seat back hinge covers. (Refer to
23 - BODY/SEATS/SEAT BACK HINGE COVERS -
50/50 SPLIT, BENCH - INSTALLATION)
(8) Verify seat back hinge operation and adjust
synchronizing cable, if equipped. (Refer to 23 -
BODY/SEATS/SYNCHRONIZING CABLE ADJUST-
MENT)
SYNCHRONIZING CABLE ADJUSTMENT
NOTE:
Bench seats equipped with child restraint seats
have an interlock feature that will not allow the seat
back to fold forward with the child seat open.
If the seat back hinges do not release at the same
time the synchronizing cable must be adjusted.
(1) Remove seat from vehicle. Refer to Owner's
Manual for proper procedures.
(2) Disengage cable from the recline mechanism by
pulling the cable end toward the front of the seat
(Fig. 93).
(3) Pull U-shaped locking tab on self-adjusting
mehcanism to disengage auto-adjust feature.
(4) Reattach self-adjusting mechanism, pulling
against spring load to tighten cable.
(5) Press locking tab onto the adjusting mecha-
nism to lock into place.
BENCH SEAT BACK
REMOVAL
NOTE: Bench seats equipped with child restraint
seats have an interlock feature that will not allow
the seat back to fold forward with the child seat
open.
(1) Remove the headrests. (Refer to 23 - BODY/
SEATS/HEADREST - REMOVAL)
(2) Remove the armrests, if equipped. (Refer to 23
- BODY/SEATS/ARMREST - REMOVAL)
(3) Remove the upper hinge cover. (Refer to 23 -
BODY/SEATS/SEAT BACK HINGE COVERS -
REMOVAL)
(4) Disengage synchronizing cable housing from
seat back hinge, if equipped.
(5) Disengage synchronizing cable end from (clip
on left side) hinge latch release arm, if equipped.
(6) Remove shoulder bolts attaching seat back
hinge to seat back frame (Fig. 94).
(7) Remove the seat back.
INSTALLATION
NOTE: Bench seats equipped with child restraint
seats have an interlock feature that will not allow
the seat back to fold forward with the child seat
open.
Fig. 93 SYNCHRONIZING CABLE
1 - CABLE END
2 - LOCKING TAB
3 - SETBACK HINGE
Fig. 94 SEAT BACK HINGE - TYPICAL
1 - SEATBACK FRAME SHOULDER BOLTS
2 - SEAT CUSHION FRAME BOLTS
3 - SEATBACK HINGE
RSSEATS23 - 147
BENCH SEAT BACK HINGE (Continued)

(1) Install the seat back.
(2) Install the shoulder bolts attaching the seat
back hinge to the seat back frame and tighten to 34
N´m (25 ft. lbs.) torque.
(3) Connect the synchronizing cable end from (clip
on left side) hinge latch release arm, if equipped.
(4) Connect the synchronizing cable housing to the
seat back hinge, if equipped.
(5) Install the upper hinge cover. (Refer to 23 -
BODY/SEATS/SEAT BACK HINGE - INSTALLA-
TION)
(6) Install the armrests, if equipped. (Refer to 23 -
BODY/SEATS/ARMREST - INSTALLATION)
(7) Install the headrest sleeves. (Refer to 23 -
BODY/SEATS/HEADREST SLEEVE - INSTALLA-
TION)
(8) Adjust synchronizing cable, if equipped. (Refer
to 23 - BODY/SEATS/SYNCHRONIZING CABLE
ADJUSTMENT)
BENCH SEAT BACK COVER
REMOVAL
(1) Remove the bench seat back. (Refer to 23 -
BODY/SEATS/BENCH SEAT BACK - REMOVAL)
(2) Remove the bench seat back panel. (Refer to 23
- BODY/SEATS/BENCH SEAT BACK PANEL -
REMOVAL)
(3) Disconnect the cover J-straps.
(4) Remove the seat back cover from the seat back
assembly.
INSTALLATION
(1) Install seat back cover onto the seat back
frame and cushion assembly.
(2) Connect the J-straps.
(3) Install the bench seat back panel. (Refer to 23 -
BODY/SEATS/BENCH SEAT BACK PANEL -
INSTALLATION)
(4) Install the seat back. (Refer to 23 - BODY/
SEATS/BENCH SEAT BACK - INSTALLATION)
BENCH SEAT TRACK
REMOVAL
(1) Remove second row seat from vehicle. Refer to
Owner's Manual for proper procedure.
(2) Place seat on clean covered work surface.
(3) Disengage seat track adjuster link wire from
track being removed.
(4) Remove nuts attaching track to seat riser (Fig.
95).
(5) Remove track from seat riser.
INSTALLATION
(1) Place track in position on seat riser.
(2) Install nuts attaching track to seat riser. (Fig.
95). Tighten nuts to 48 N´m (35 ft. lbs.) torque.
(3) Engage seat track adjuster link wire onto track
being installed.
(4) Install second row seat into vehicle.
Fig. 95 BENCH SEAT TRACK
1 - SEAT TRACK ADJUSTER LINK
2 - RISER
3 - SEAT TRACK NUTS
4 - SEAT TRACK
5 - RISER BOLTS
23 - 148 SEATSRS
BENCH SEAT BACK (Continued)

BOTTOM OF SEAT CUSHION
PAN PANEL-THIRD ROW -
FOLD-IN-FLOOR
REMOVAL
(1) Fold the third row seat with back down.
(2) Remove handle from cushion.
(3) Using a trim tool, remove bottom side of the
cushion pan panel (Fig. 105).
INSTALLATION
(1) Place bottom side of the cushion pan panel into
position (Fig. 106).
(2) Press on back of cushion pan panel to seat the
fasteners.
(3) Install handle on cushion.
(4) Place seat in the up right position.
HEADREST SLEEVE - THIRD
ROW - FOLD-IN-FLOOR
REMOVAL
(1) Remove headrest (Fig. 107).
(2) Using a trim tool remove sleeve by prying
sleeve away from the seat back frame to unlock it
(Fig. 108)
(3) Pull headrest sleeve upward and out the top of
the seat back frame and remove from seat.
Fig. 105 THIRD ROW CUSHION PAN & COVER
Fig. 106 THIRD ROW CUSHION PAN & COVER
Fig. 107 HEADREST
1 - HEADREST
2 - DEPRESS TAB
Fig. 108 REMOVING HEADREST SLEEVES
1 - HEADREST SLEEVES
2 - TRIM TOOL
23 - 152 SEATSRS

INSTALLATION
(1) Place headrest sleeve into position and push
downward until sleeve locks into position (Fig. 109).
(2) Install headrest (Fig. 107).
SEAT - THIRD ROW - FOLD-IN-
FLOOR
REMOVAL
(1) Fold third row seat into floor well.
(2) Using a trim stick, unclip anchor molding (Fig.
110).
(3) Remove third row seat attaching bolts (Fig.
111).
(4) Raise seats to the upright position.
(5) Remove the rear seat lower trim cover (Fig.
112).
(6) Remove rear attaching bolts (Fig. 113).
(7) Remove rear seat from vehicle.
Fig. 109 HEADREST SLEEVES
1 - SLEEVES
Fig. 110 ANCHOR MOLDING
1 - 2-WAY CLIPS INTO SEAT FRAME
2 - 4-WAY LOCATING PINS (2)
3 - FRONT SEAT ANCHOR MOLDING
Fig. 111 THIRD ROW SEATS
1 - ATTACHING BOLTS
RSSEATS23 - 153
HEADREST SLEEVE - THIRD ROW - FOLD-IN-FLOOR (Continued)

FILTER ADAPTER - INSTALLATION, OIL . . . 9-142
FILTER ADAPTER - REMOVAL, OIL.......9-142
FILTER CHANGE - STANDARD PROCEDURE, ENGINE OIL ..........9-139,9-54
FILTER SERVICE - STANDARD PROCEDURE, FLUID ............21-231,21-82
FINAL DRIVE - ASSEMBLY .......21-224,21-78
FINAL DRIVE - DESCRIPTION .....21-219,21-74
FINAL DRIVE - DISASSEMBLY ....21-220,21-75
FINAL DRIVE - OPERATION .......21-220,21-75
FINESSE SANDING/BUFFING & POLISHING - DESCRIPTION ...........23-101
FINISH - DESCRIPTION, BASE COAT/CLEARCOAT ................... 23-101
FIRING ORDER, SPECIFICATIONS .........8I-3
FIRST ROW - BENCH - INSTALLATION, SEAT BELT BUCKLE .................. 8O-37
FIRST ROW - BENCH - REMOVAL, SEAT BELT BUCKLE ....................... 8O-36
FIRST ROW - OUTBOARD - INSTALLATION, SEAT BELT &
RETRACTOR ........................ 8O-40
FIRST ROW - OUTBOARD - REMOVAL, SEAT BELT & RETRACTOR .............8O-39
FIRST ROW INBOARD - QUAD BUCKET - INSTALLATION, SEAT BELT BUCKLE ......8O-36
FIRST ROW INBOARD - QUAD BUCKET - REMOVAL, SEAT BELT BUCKLE .........8O-35
FITTING - CONNECTING ROD ............9-46
FITTING - PISTON RING ................9-47
FITTING - STANDARD PROCEDURE, MAIN BEARING ...................... 9-125
FITTING - STANDARD PROCEDURE, PISTON RING ....................... 9-124
FITTING - STANDARD PROCEDURE, PISTON TO CYLINDER BORE ............9-44
FITTING CONNECTING RODS - STANDARD PROCEDURE ...............9-119
FITTING DISASSEMBLY/ASSEMBLY - STANDARD PROCEDURE,
TRANSMISSION COOLER LINE QUICK
CONNECT ............................ 7-38
FITTING PISTONS - STANDARD PROCEDURE ........................ 9-120
FITTINGS - STANDARD PROCEDURE, QUICK-CONNECT ..................... 14-18
FITTINGS, STANDARD PROCEDURE - HANDLING TUBING ................... 24-69
FLAP AND SPRING ASSEMBLY - INSTALLATION, QUAD BUCKET SEAT
SIDE SHIELD/CUP HOLDER ............23-151
FLAP AND SPRING ASSEMBLY - REMOVAL, QUAD BUCKET SEAT SIDE
SHIELD/CUP HOLDER ................23-151
FLEX DRIVE - DESCRIPTION ...........8N-55
FLEX DRIVE - INSTALLATION ...........8N-56
FLEX DRIVE - OPERATION .............8N-55
FLEX DRIVE - REMOVAL ...............8N-55
FLEX PLATE - INSTALLATION ...........9-133
FLEX PLATE - REMOVAL ...............9-133
FLEXIBLE FUEL ENGINE OIL - DESCRIPTION .........................0-3
FLOOR CONSOLE - FOLD-IN-FLOOR - INSTALLATION ....................... 23-89
FLOOR CONSOLE - FOLD-IN-FLOOR - REMOVAL .......................... 23-89
FLOOR CONSOLE BASE TRAY - INSTALLATION ....................... 23-89
FLOOR CONSOLE BASE TRAY - REMOVAL .......................... 23-89
FLOOR CONSOLE KEY LOCK TUMBLER - FOLD-IN-FLOOR - INSTALLATION ........23-90
FLOOR CONSOLE KEY LOCK TUMBLER - FOLD-IN-FLOOR - REMOVAL ............23-90
FLOOR CONSOLE LID LATCH - FOLD-IN-FLOOR - INSTALLATION ........23-90
FLOOR CONSOLE LID LATCH - FOLD-IN-FLOOR - REMOVAL ............23-90
FLOOR DISTRIBUTION DUCTS - INSTALLATION ....................... 24-50
FLOOR DISTRIBUTION DUCTS - REMOVAL .......................... 24-50
FLOOR HEAT DUCT - INSTALLATION, REAR .............................. 24-63
FLOOR HEAT DUCT - REMOVAL, REAR . . . 24-63
FLOOR MATS - INSTALLATION, CARPETS . 23-81
FLOOR MATS - REMOVAL, CARPETS .....23-81 FLOOR TUB CARPET INSERT -
FOLD-IN-FLOOR - INSTALLATION,
SECOND ROW ....................... 23-98
FLOOR TUB CARPET INSERT - FOLD-IN-FLOOR - REMOVAL, SECOND
ROW .............................. 23-98
FLOOR TUB CARPETS INSERT - FOLD-IN-FLOOR - INSTALLATION,
REAR .............................. 23-96
FLOOR TUB CARPETS INSERT - FOLD-IN-FLOOR - REMOVAL, REAR ......23-95
FLOW AND PRESSURE TEST - DIAGNOSIS AND TESTING, POWER
STEERING SYSTEM .................... 19-1
FLOW CHECK - DIAGNOSIS AND TESTING, COOLING SYSTEM .............7-3
FLUID - DESCRIPTION, AUTOMATIC/ MANUAL TRANSAXLE ...................0-4
FLUID - DESCRIPTION, AWD POWER TRANSFER UNIT .......................0-6
FLUID AND FILTER SERVICE - STANDARD PROCEDURE .........21-231,21-82
FLUID CAPACITIES - SPECIFICATIONS ......0-6
FLUID CONTAMINATION - DIAGNOSIS AND TESTING, BRAKE .................. 5-33
FLUID COOLER - DESCRIPTION .........19-45
FLUID COOLER - INSTALLATION .........19-45
FLUID COOLER - OPERATION ...........19-45
FLUID COOLER - REMOVAL ............19-45
FLUID FILL/CHECK LOCATIONS - DESCRIPTION .........................0-7
FLUID LEAKAGE - DIAGNOSIS AND TESTING, TORQUE CONVERTER
HOUSING ....................... 21-154,21-9
FLUID LEVEL AND CONDITION CHECK, STANDARD PROCEDURE .........21-230,21-82
FLUID LEVEL CHECKING - STANDARD PROCEDURE, BRAKE ................... 5-33
FLUID LEVEL CHECKING - STANDARD PROCEDURE, POWER STEERING ........19-44
FLUID LEVEL SWITCH - DESCRIPTION, BRAKE .............................. 5-10
FLUID LEVEL SWITCH - INSTALLATION, BRAKE .............................. 5-11
FLUID LEVEL SWITCH - INSTALLATION, WASHER ........................... 8R-11
FLUID LEVEL SWITCH - OPERATION, BRAKE .............................. 5-10
FLUID LEVEL SWITCH - REMOVAL, BRAKE .............................. 5-11
FLUID LEVEL SWITCH - REMOVAL, WASHER ........................... 8R-11
FLUID, SPECIFICATIONS - BRAKE .........5-33
FLUIDS - DESCRIPTION, AWD REAR DRIVELINE MODULE ....................0-6
FLUSH MEASUREMENTS - SPECIFICATIONS, GAP ................23-177
FOG LAMP - DIAGNOSIS AND TESTING, FRONT .............................. 8L-7
FOG LAMP - INSTALLATION, FRONT .......8L-8
FOG LAMP - REMOVAL, FRONT ..........8L-8
FOG LAMP UNIT ALIGNMENT - EXPORT - STANDARD PROCEDURE, FRONT ........8L-9
FOG LAMP UNIT ALIGNMENT - STANDARD PROCEDURE, FRONT .........8L-9
FOLDAWAY MIRROR SWITCH - EXPORT - DESCRIPTION, POWER ..............8N-29
FOLDAWAY MIRROR SWITCH - EXPORT - INSTALLATION, POWER ..............8N-30
FOLDAWAY MIRROR SWITCH - EXPORT - OPERATION, POWER ................8N-29
FOLDAWAY MIRROR SWITCH - EXPORT - REMOVAL, POWER .................. 8N-29
FOLD-IN-FLOOR - INSTALLATION . . . 14-10,14-16
FOLD-IN-FLOOR - INSTALLATION, ARMREST - SECOND ROW ............23-130
FOLD-IN-FLOOR - INSTALLATION, ARMREST ROTATING ASSEMBLY -
SECOND ROW ...................... 23-130
FOLD-IN-FLOOR - INSTALLATION, BOTTOM OF SEAT CUSHION PAN
PANEL-THIRD ROW .................. 23-152
FOLD-IN-FLOOR - INSTALLATION, CARPET TRIM RING AND COVER ........23-84
FOLD-IN-FLOOR - INSTALLATION, CARPETS ........................... 23-83
FOLD-IN-FLOOR - INSTALLATION, FLOOR CONSOLE ........................... 23-89FOLD-IN-FLOOR - INSTALLATION, FLOOR
CONSOLE KEY LOCK TUMBLER .........23-90
FOLD-IN-FLOOR - INSTALLATION, FLOOR CONSOLE LID LATCH .................23-90
FOLD-IN-FLOOR - INSTALLATION, HEADREST SLEEVE - SECOND ROW .....23-131
FOLD-IN-FLOOR - INSTALLATION, HEADREST SLEEVE - THIRD ROW ......23-153
FOLD-IN-FLOOR - INSTALLATION, REAR FLOOR TUB CARPETS INSERT ..........23-96
FOLD-IN-FLOOR - INSTALLATION, SEAT - SECOND ROW ...................... 23-132
FOLD-IN-FLOOR - INSTALLATION, SEAT - THIRD ROW ........................ 23-154
FOLD-IN-FLOOR - INSTALLATION, SEAT BACK COVER/FOAM - SECOND ROW ....23-133
FOLD-IN-FLOOR - INSTALLATION, SEAT BACK COVER/FOAM - THIRD ROW ......23-156
FOLD-IN-FLOOR - INSTALLATION, SEAT BACK FRAME - SECOND ROW .........23-134
FOLD-IN-FLOOR - INSTALLATION, SEAT BACK FRAME - THIRD ROW ...........23-157
FOLD-IN-FLOOR - INSTALLATION, SEAT BACKSTOW STRAP - THIRD ROW ......23-158
FOLD-IN-FLOOR - INSTALLATION, SEAT BASE RISER - SECOND ROW ..........23-135
FOLD-IN-FLOOR - INSTALLATION, SEAT BELT CENTER LAP BELT ..............23-157
FOLD-IN-FLOOR - INSTALLATION, SEAT CUSHION COVER/FOAM - THIRD ROW . . . 23-159
FOLD-IN-FLOOR - INSTALLATION, SEAT CUSHION COVER/FOAM -SECOND
ROW ............................. 23-136
FOLD-IN-FLOOR - INSTALLATION, SEAT CUSHION SIDE SHIELD - SECOND
ROW ............................. 23-138
FOLD-IN-FLOOR - INSTALLATION, SEAT GAS STRUT - SECOND ROW ...........23-139
FOLD-IN-FLOOR - INSTALLATION, SEAT PROP ROD - SECOND ROW ...........23-140
FOLD-IN-FLOOR - INSTALLATION, SECOND ROW FLOOR TUB CARPET
INSERT ............................ 23-98
FOLD-IN-FLOOR - INSTALLATION, SIDE SHIELD CUP HOLDER ................23-160
FOLD-IN-FLOOR - INSTALLATION, WITH NVLD .............................. 25-20
FOLD-IN-FLOOR - REMOVAL .......14-10,14-13
FOLD-IN-FLOOR - REMOVAL, ARMREST - SECOND ROW ..................... 23-130
FOLD-IN-FLOOR - REMOVAL, ARMREST ROTATING ASSEMBLY - SECOND ROW . . 23-130
FOLD-IN-FLOOR - REMOVAL, BOTTOM OF SEAT CUSHION PAN PANEL-THIRD
ROW ............................. 23-152
FOLD-IN-FLOOR - REMOVAL, CARPET TRIM RING AND COVER ...............23-84
FOLD-IN-FLOOR - REMOVAL, CARPETS . . . 23-82
FOLD-IN-FLOOR - REMOVAL, FLOOR CONSOLE ........................... 23-89
FOLD-IN-FLOOR - REMOVAL, FLOOR CONSOLE KEY LOCK TUMBLER .........23-90
FOLD-IN-FLOOR - REMOVAL, FLOOR CONSOLE LID LATCH .................23-90
FOLD-IN-FLOOR - REMOVAL, HEADREST SLEEVE - SECOND ROW ..............23-131
FOLD-IN-FLOOR - REMOVAL, HEADREST SLEEVE - THIRD ROW ...............23-152
FOLD-IN-FLOOR - REMOVAL, REAR FLOOR TUB CARPETS INSERT ..........23-95
FOLD-IN-FLOOR - REMOVAL, SEAT - SECOND ROW ...................... 23-132
FOLD-IN-FLOOR - REMOVAL, SEAT - THIRD ROW ........................ 23-153
FOLD-IN-FLOOR - REMOVAL, SEAT BACK COVER/FOAM - SECOND ROW .........23-133
FOLD-IN-FLOOR - REMOVAL, SEAT BACK COVER/FOAM - THIRD ROW ...........23-155
FOLD-IN-FLOOR - REMOVAL, SEAT BACK FRAME - SECOND ROW ..............23-134
FOLD-IN-FLOOR - REMOVAL, SEAT BACK FRAME - THIRD ROW ................23-156
FOLD-IN-FLOOR - REMOVAL, SEAT BACKSTOW STRAP - THIRD ROW ......23-158
FOLD-IN-FLOOR - REMOVAL, SEAT BASE RISER - SECOND ROW ...............23-134
FOLD-IN-FLOOR - REMOVAL, SEAT BELT CENTER LAP BELT ................... 23-157
RS INDEX13
Description Group-Page Description Group-Page Description Group-Page

HCU (HYDRAULIC CONTROL UNIT) -OPERATION ......................... 5-101
HEAD - CLEANING, CYLINDER ......9-103,9-26
HEAD - DESCRIPTION, CYLINDER . . . 9-102,9-25
HEAD - INSPECTION, CYLINDER .....9-104,9-27
HEAD - INSTALLATION, CYLINDER . . . 9-104,9-27
HEAD - REMOVAL, CYLINDER ......9-103,9-26
HEAD COVER - CLEANING, CYLINDER .....9-31
HEAD COVER - INSPECTION, CYLINDER . . . 9-31
HEAD COVER - INSTALLATION, CYLINDER ........................... 9-32
HEAD COVER - LEFT - INSTALLATION, CYLINDER .......................... 9-107
HEAD COVER - LEFT - REMOVAL, CYLINDER .......................... 9-107
HEAD COVER - REMOVAL, CYLINDER .....9-31
HEAD COVER - RIGHT - INSTALLATION, CYLINDER .......................... 9-106
HEAD COVER - RIGHT - REMOVAL, CYLINDER .......................... 9-106
HEAD COVER(S) - DESCRIPTION, CYLINDER .......................... 9-105
HEAD GASKET - DIAGNOSIS AND TESTING, CYLINDER ..............9-102,9-25
HEAD OFF - INSTALLATION, CYLINDER . . . 9-111, 9-33
HEAD OFF - REMOVAL, CYLINDER . . . 9-109,9-33
HEAD ON - INSTALLATION, CYLINDER . . . 9-111, 9-33
HEAD ON - REMOVAL, CYLINDER . . . 9-111,9-33
HEADER TRIM - INSTALLATION, REAR ....23-96
HEADER TRIM - REMOVAL, REAR .......23-96
HEADLAMP - DIAGNOSIS AND TESTING . . 8L-11
HEADLAMP - INSTALLATION ............8L-13
HEADLAMP - REMOVAL ...............8L-12
HEADLAMP SWITCH - DIAGNOSIS AND TESTING ........................... 8L-13
HEADLAMP SWITCH - INSTALLATION ....8L-13
HEADLAMP SWITCH - REMOVAL ........8L-13
HEADLAMP UNIT - EXPORT - INSTALLATION ....................... 8L-17
HEADLAMP UNIT - EXPORT - REMOVAL . . 8L-17
HEADLAMP UNIT - INSTALLATION .......8L-15
HEADLAMP UNIT - REMOVAL ...........8L-15
HEADLAMP UNIT ALIGNMENT - EXPORT - STANDARD PROCEDURE .............8L-15
HEADLAMP UNIT ALIGNMENT - STANDARD PROCEDURE ...............8L-14
HEADLINER - INSTALLATION ...........23-92
HEADLINER - REMOVAL ...............23-91
HEADREST - INSTALLATION ...........23-106
HEADREST - REMOVAL ...............23-106
HEADREST SLEEVE - INSTALLATION ....23-107
HEADREST SLEEVE - REMOVAL ........23-107
HEADREST SLEEVE - SECOND ROW - FOLD-IN-FLOOR - INSTALLATION .......23-131
HEADREST SLEEVE - SECOND ROW - FOLD-IN-FLOOR - REMOVAL ...........23-131
HEADREST SLEEVE - THIRD ROW - FOLD-IN-FLOOR - INSTALLATION .......23-153
HEADREST SLEEVE - THIRD ROW - FOLD-IN-FLOOR - REMOVAL ...........23-152
HEAT DUCT - INSTALLATION, REAR FLOOR ............................. 24-63
HEAT DUCT - REMOVAL, REAR FLOOR . . . 24-63
HEAT SHIELDS - DESCRIPTION ..........11-7
HEAT SHIELDS - INSTALLATION ..........11-7
HEAT SHIELDS - OPERATION ............11-7
HEAT SHIELDS - REMOVAL .............11-7
HEAT STAKING - STANDARD PROCEDURE ......................... 23-9
HEATED GLASS - DESCRIPTION ..........8G-1
HEATED GLASS - OPERATION ...........8G-2
HEATED MIRRORS - DESCRIPTION .......8G-6
HEATED MIRRORS - OPERATION .........8G-6
HEATED SEAT ELEMENTS - DESCRIPTION ....................... 8G-11
HEATED SEAT ELEMENTS - OPERATION . . 8G-11
HEATED SEAT ELEMENTS, DIAGNOSIS AND TESTING ....................... 8G-11
HEATED SEAT MODULE - DESCRIPTION ....8E-8
HEATED SEAT MODULE - OPERATION .....8E-8
HEATED SEAT MODULE, DIAGNOSIS AND TESTING ............................ 8E-9
HEATED SEAT SENSOR - DESCRIPTION . . . 8G-13
HEATED SEAT SENSOR - OPERATION ....8G-13
HEATED SEAT SENSOR, DIAGNOSIS AND TESTING ........................... 8G-13HEATED SEAT SWITCH - DESCRIPTION
....8G-8
HEATED SEAT SWITCH - OPERATION ......8G-9
HEATED SEAT SWITCH, DIAGNOSIS AND TESTING - DRIVER .................... 8G-9
HEATED SEAT SYSTEM - DESCRIPTION ....8G-7
HEATED SEAT SYSTEM - OPERATION .....8G-8
HEATED SEAT SYSTEM, DIAGNOSIS AND TESTING ............................ 8G-8
HEATER - DESCRIPTION, CABIN ........24-113
HEATER - DESCRIPTION, ENGINE BLOCK . . . 7-20
HEATER - INSTALLATION, ENGINE BLOCK .............................. 7-21
HEATER - OPERATION, ENGINE BLOCK ....7-20
HEATER - REMOVAL, ENGINE BLOCK ......7-21
HEATER AND AIR CONDITIONER, DESCRIPTION ........................ 24-1
HEATER AND AIR CONDITIONER, OPERATION .......................... 24-4
HEATER CONTROL - DESCRIPTION, A/C . . . 24-19
HEATER CORE - DESCRIPTION ....24-102,24-83
HEATER CORE - OPERATION ......24-102,24-84
HEATER CORE FILLING, STANDARD PROCEDURE - REAR .................24-102
HEATER CORE, INSTALLATION - FRONT . . . 24-86
HEATER CORE, REMOVAL - FRONT ......24-85
HEATER CORE TUBES, INSTALLATION - FRONT ............................. 24-85
HEATER CORE TUBES, REMOVAL - FRONT ............................. 24-84
HEATER, DIAGNOSIS AND TESTING - SUPPLEMENTAL CABIN ...............24-114
HEATER HOSES - INSTALLATION . 24-105,24-119
HEATER HOSES - REMOVAL .....24-104,24-119
HEATER INLET HOSE - INSTALLATION ....24-87
HEATER INLET HOSE - REMOVAL ........24-86
HEATER PERFORMANCE TEST, DIAGNOSIS AND TESTING .............24-10
HEATER PIPES - INSTALLATION ........24-120
HEATER PIPES - REMOVAL ............24-119
HEATER RETURN HOSE - INSTALLATION . . 24-89
HEATER RETURN HOSE - REMOVAL ......24-88
HEATER TESTING - DIAGNOSIS AND TESTING, ENGINE BLOCK ...............7-21
HEATER TUBES, INSTALLATION - UNDERBODY ....................... 24-112
HEATER TUBES, REMOVAL - UNDERBODY ....................... 24-109
HEATER UNIT - INSTALLATION .........24-122
HEATER UNIT - REMOVAL .............24-121
HEATER WIRING - INSTALLATION ......24-122
HEATER WIRING - REMOVAL ..........24-122
HEAVY DUTY, CARGO - INSTALLATION, AWD ............................... 2-36
HEAVY DUTY, CARGO - REMOVAL, AWD . . . 2-36
HEIGHT ADJUSTE R-BORC-PILLAR -
INSTALLATION, SEAT BELT .............8O-38
HEIGHT ADJUSTE R-BORC-PILLAR -
REMOVAL, SEAT BELT ................8O-38
HEIGHT ADJUSTER KNOB - INSTALLATION, SEAT BELT .............8O-38
HEIGHT ADJUSTER KNOB - REMOVAL, SEAT BELT ......................... 8O-38
HEIGHT MEASUREMENT - STANDARD PROCEDURE, CURB ................... 2-55
HIGH AND LOW LIMITS, DESCRIPTION ....25-9
HIGH MOUNTED STOP LAMP - INSTALLATION, CENTER ................8L-6
HIGH MOUNTED STOP LAMP - REMOVAL, CENTER .................... 8L-6
HIGH MOUNTED STOP LAMP UNIT - INSTALLATION, CENTER ................8L-6
HIGH MOUNTED STOP LAMP UNIT - REMOVAL, CENTER .................... 8L-6
HIGH PRESSURE RELIEF VALVE, DESCRIPTION ....................... 24-72
HIGH PRESSURE RELIEF VALVE, OPERATION ......................... 24-72
HIGH SPEED OPERATION - STANDARD PROCEDURE, TIRE PRESSURE ..........22-17
HINGE - INSTALLATION ......23-18,23-40,23-62
HINGE - INSTALLATION, CENTER ........23-24
HINGE - INSTALLATION, LOWER ........23-28
HINGE - INSTALLATION, UPPER .........23-36
HINGE - REMOVAL .........23-17,23-40,23-62
HINGE - REMOVAL, BENCH SEAT BACK . . 23-146
HINGE - REMOVAL, CENTER ............23-24
HINGE - REMOVAL, LOWER ............23-28
HINGE - REMOVAL, UPPER .............23-36HINGE COVERS - QUAD BUCKET, 50/50
SPLIT, BENCH - INSTALLATION, SEAT
BACK ............................. 23-146
HINGE COVERS - QUAD BUCKET, 50/50 SPLIT, BENCH - REMOVAL, SEAT BACK . . 23-146
HOISTING - STANDARD PROCEDURE ......0-24
HOLDDOWN - INSTALLATION, BATTERY . . . 8F-16
HOLDDOWN - REMOVAL, BATTERY ......8F-16
HOLDER - FLAP AND SPRING ASSEMBLY - INSTALLATION, QUAD
BUCKET SEAT SIDE SHIELD/CUP .......23-151
HOLDER - FLAP AND SPRING ASSEMBLY - REMOVAL, QUAD BUCKET
SEAT SIDE SHIELD/CUP ..............23-151
HOLDER - FOLD-IN-FLOOR - INSTALLATION, SIDE SHIELD CUP ......23-160
HOLDER - FOLD-IN-FLOOR - REMOVAL, SIDE SHIELD CUP ................... 23-160
HOLDER - INSTALLATION, CUP .........23-65
HOLDER - INSTALLATION, QUAD BUCKET SEAT SIDE SHIELD - NO CUP . . . 23-143
HOLDER - INSTALLATION, QUAD BUCKET SEAT SIDE SHIELD/CUP .......23-142
HOLDER - REMOVAL, CUP .............23-65
HOLDER - REMOVAL, QUAD BUCKET SEAT SIDE SHIELD - NO CUP ..........23-143
HOLDER - REMOVAL, QUAD BUCKET SEAT SIDE SHIELD/CUP ..............23-141
HOLDING CLUTCHES - DESCRIPTION . . . 21-236, 21-86
HOLDING CLUTCHES - OPERATION .....21-236,
21-86
HONING - STANDARD PROCEDURE, CYLINDER BORE ................. 9-115,9-36
HOOD - INSTALLATION ................23-63
HOOD - REMOVAL .................... 23-62
HOOD AJAR SWITCH - EXPORT - INSTALLATION ....................... 8Q-3
HOOD AJAR SWITCH - EXPORT - REMOVAL ........................... 8Q-3
HORN CHIRP PREFERENCE - STANDARD PROCEDURE ........................ 8N-24
HORN, DIAGNOSIS AND TESTING ........8H-3
HORN SWITCH - DESCRIPTION ..........8H-4
HORN SYSTEM - DESCRIPTION ..........8H-1
HORN SYSTEM - OPERATION ............8H-1
HORN SYSTEM, DIAGNOSIS AND TESTING ............................ 8H-1
HOSE - INSTALLATION, HEATER INLET ....24-87
HOSE - INSTALLATION, HEATER RETURN . 24-89
HOSE - REMOVAL, HEATER INLET .......24-86
HOSE - REMOVAL, HEATER RETURN .....24-88
HOSE CLAMPS - DESCRIPTION ...........7-1
HOSE CLAMPS - OPERATION .............7-2
HOSES - DESCRIPTION, BRAKE TUBES ....5-14
HOSES - INSPECTION, BRAKE TUBES .....5-14
HOSES - INSTALLATION, HEATER . 24-105,24-119
HOSES - INSTALLATION, WASHER .......8R-12
HOSES - OPERATION, BRAKE TUBES ......5-14
HOSES - REMOVAL, HEATER ....24-104,24-119
HOSES - REMOVAL, WASHER ..........8R-11
HOSES AND CLAMP - STANDARD PROCEDURE ......................... 14-7
HOUSING - INSTALLATION, AIR CLEANER ....................... 9-102,9-25
HOUSING - INSTALLATION, HVAC ........24-62
HOUSING - REMOVAL, AIR CLEANER . 9-101,9-25
HOUSING - REMOVAL, HVAC ...........24-60
HOUSING FLUID LEAKAGE - DIAGNOSIS AND TESTING, TORQUE CONVERTER . . . 21-154,
21-9
HUB / BEARING - DESCRIPTION .......2-30,2-5
HUB / BEARING - INSTALLATION ......2-33,2-5
HUB / BEARING - OPERATION ........2-30,2-5
HUB / BEARING - REMOVAL ..........2-31,2-5
HUB AND BEARING - DIAGNOSIS AND TESTING ......................... 2-31,2-5
HVAC - LWB - INSTALLATION, SEAT BELT & RETRACTOR - SECOND ROW -
RIGHT OUTBOARD WITH REAR .........8O-41
HVAC - LWB - REMOVAL, SEAT BELT & RETRACTOR - SECOND ROW - RIGHT
OUTBOARD WITH REAR ...............8O-41
HVAC HOUSING - INSTALLATION ........24-62
HVAC HOUSING - REMOVAL ............24-60
HVAC LOUVER - INSTALLATION, REAR . . . 23-97
HVAC LOUVER - REMOVAL, REAR .......23-96
16 INDEXRS
Description Group-Page Description Group-Page Description Group-Page

SEAT STORAGE BIN GUIDE - REMOVAL,UNDER ............................ 23-150
SEAT STORAGE BIN LOCK/LATCH - INSTALLATION, UNDER ...............23-150
SEAT STORAGE BIN LOCK/LATCH - REMOVAL, UNDER .................. 23-150
SEAT SWITCH - DESCRIPTION ..........8N-34
SEAT SWITCH - DESCRIPTION, HEATED . . . 8G-8
SEAT SWITCH - OPERATION ............8N-34
SEAT SWITCH - OPERATION, HEATED .....8G-9
SEAT SWITCH, DIAGNOSIS AND TESTING - DRIVER ................... 8N-34
SEAT SWITCH, DIAGNOSIS AND TESTING - DRIVER HEATED .............8G-9
SEAT SYSTEM - DESCRIPTION, HEATED . . . 8G-7
SEAT SYSTEM - OPERATION, HEATED .....8G-8
SEAT SYSTEM, DESCRIPTION - POWER . . 8N-31
SEAT SYSTEM, DIAGNOSIS AND TESTING - HEATED .................... 8G-8
SEAT SYSTEM, DIAGNOSIS AND TESTING - POWER ................... 8N-33
SEAT SYSTEM, OPERATION - POWER ....8N-32
SEAT TRACK - DESCRIPTION, POWER ....8N-37
SEAT TRACK - INSTALLATION, BENCH . . . 23-148
SEAT TRACK - OPERATION, POWER .....8N-38
SEAT TRACK - REAR COVER - INSTALLATION, FRONT ...............23-128
SEAT TRACK - REAR COVER - REMOVAL, FRONT ................... 23-128
SEAT TRACK - REMOVAL, BENCH ........23-148
SEAT TRACK ADJUSTER/MANUAL - OCS - INSTALLATION, FRONT ..............23-128
SEAT TRACK ADJUSTER/MANUAL - OCS - REMOVAL, FRONT .................23-126
SEAT TRACK ADJUSTER/POWER - OCS - INSTALLATION, FRONT ...............23-125
SEAT TRACK ADJUSTER/POWER - OCS - REMOVAL, FRONT ................... 23-124
SEAT TRACK, DIAGNOSIS AND TESTING - POWER ........................... 8N-38
SEAT TRACK MANUAL ADJUSTER - INSTALLATION, FRONT ...............23-126
SEAT TRACK MANUAL ADJUSTER - REMOVAL, FRONT ................... 23-125
SEAT TRACK POWER ADJUSTER - INSTALLATION, FRONT ...............23-124
SEAT TRACK POWER ADJUSTER - REMOVAL, FRONT ................... 23-124
SEAT TRACK REAR COVER - OCS - INSTALLATION, FRONT ...............23-129
SEAT TRACK REAR COVER - OCS - REMOVAL, FRONT ................... 23-129
SEAT WEIGHT BLADDER & PRESSURE SENSOR - DESCRIPTION ..............8O-43
SEAT WEIGHT BLADDER & PRESSURE SENSOR - OPERATION ................8O-44
SEATING - INSTALLATION, FOLD-IN- FLOOR .......................... 5-68,5-75
SEATING - INSTALLATION, FWD - FOLD-IN-FLOOR ....................... 2-45
SEATING - REMOVAL, FOLD-IN-FLOOR . 5-66,5-72
SEATING - REMOVAL, FWD - FOLD-IN- FLOOR .............................. 2-45
SEAT/MIRROR MODULE - DESCRIPTION, MEMORY ............................ 8E-9
SEAT/MIRROR MODULE - OPERATION, MEMORY ............................ 8E-9
SEAT/MIRROR MODULE, DIAGNOSIS AND TESTING - MEMORY ...............8E-9
SEATS - CLEANING, INTAKE/EXHAUST VALVES ........................ 9-108,9-33
SEATS - DESCRIPTION, INTAKE/ EXHAUST VALVES ................ 9-107,9-33
SEATS - INSPECTION, INTAKE/EXHAUST VALVES ............................ 9-108
SEATS - INSTALLATION, INTAKE/ EXHAUST VALVES .................... 9-109
SEATS - OPERATION, INTAKE/EXHAUST VALVES ............................ 9-107
SEATS - REMOVAL, INTAKE/EXHAUST VALVES ............................ 9-108
SEATS - STANDARD PROCEDURE, REFACING VALVES AND VALVE ..........9-107
SEATS ONLY - SPECIFICATIONS, FRAME DIMENSIONS - FOLD-IN-FLOOR .........13-11
SECOND ROW - FOLD-IN-FLOOR - INSTALLATION, ARMREST ............23-130SECOND ROW - FOLD-IN-FLOOR -
INSTALLATION, ARMREST ROTATING
ASSEMBLY ......................... 23-130
SECOND ROW - FOLD-IN-FLOOR - INSTALLATION, HEADREST SLEEVE .....23-131
SECOND ROW - FOLD-IN-FLOOR - INSTALLATION, SEAT .................23-132
SECOND ROW - FOLD-IN-FLOOR - INSTALLATION, SEAT BACK COVER/
FOAM ............................. 23-133
SECOND ROW - FOLD-IN-FLOOR - INSTALLATION, SEAT BACK FRAME .....23-134
SECOND ROW - FOLD-IN-FLOOR - INSTALLATION, SEAT BASE RISER ......23-135
SECOND ROW - FOLD-IN-FLOOR - INSTALLATION, SEAT CUSHION SIDE
SHIELD ........................... 23-138
SECOND ROW - FOLD-IN-FLOOR - INSTALLATION, SEAT GAS STRUT ......23-139
SECOND ROW - FOLD-IN-FLOOR - INSTALLATION, SEAT PROP ROD .......23-140
SECOND ROW - FOLD-IN-FLOOR - REMOVAL, ARMREST ................23-130
SECOND ROW - FOLD-IN-FLOOR - REMOVAL, ARMREST ROTATING
ASSEMBLY ......................... 23-130
SECOND ROW - FOLD-IN-FLOOR - REMOVAL, HEADREST SLEEVE .........23-131
SECOND ROW - FOLD-IN-FLOOR - REMOVAL, SEAT .................... 23-132
SECOND ROW - FOLD-IN-FLOOR - REMOVAL, SEAT BACK COVER/FOAM ....23-133
SECOND ROW - FOLD-IN-FLOOR - REMOVAL, SEAT BACK FRAME .........23-134
SECOND ROW - FOLD-IN-FLOOR - REMOVAL, SEAT BASE RISER ..........23-134
SECOND ROW - FOLD-IN-FLOOR - REMOVAL, SEAT CUSHION SIDE
SHIELD ........................... 23-138
SECOND ROW - FOLD-IN-FLOOR - REMOVAL, SEAT GAS STRUT ..........23-138
SECOND ROW - FOLD-IN-FLOOR - REMOVAL, SEAT PROP ROD ...........23-139
SECOND ROW - INSTALLATION, BENCH SEAT RISER ........................ 23-145
SECOND ROW - LEFT OUTBOARD - INSTALLATION, SEAT BELT &
RETRACTOR ........................ 8O-42
SECOND ROW - LEFT OUTBOARD - REMOVAL, SEAT BELT & RETRACTOR ....8O-42
SECOND ROW - REMOVAL, BENCH SEAT RISER ............................ 23-145
SECOND ROW - RIGHT OUTBOARD - INSTALLATION, SEAT BELT &
RETRACTOR ........................ 8O-40
SECOND ROW - RIGHT OUTBOARD - REMOVAL, SEAT BELT & RETRACTOR ....8O-40
SECOND ROW - RIGHT OUTBOARD WITH REAR HVAC - LWB -
INSTALLATION, SEAT BELT &
RETRACTOR ........................ 8O-41
SECOND ROW - RIGHT OUTBOARD WITH REAR HVAC - LWB - REMOVAL,
SEAT BELT & RETRACTOR .............8O-41
SECOND ROW - THREE PASSENGER BENCH - INSTALLATION, SEAT BELT
BUCKLE ............................ 8O-40
SECOND ROW - THREE PASSENGER BENCH - REMOVAL, SEAT BELT
BUCKLE ............................ 8O-40
SECOND ROW FLOOR TUB CARPET INSERT - FOLD-IN-FLOOR -
INSTALLATION ....................... 23-98
SECOND ROW FLOOR TUB CARPET INSERT - FOLD-IN-FLOOR - REMOVAL ....23-98
SECOND ROW -FOLD-IN-FLOOR - INSTALLATION, SEAT BACK PANEL ......23-134
SECOND ROW -FOLD-IN-FLOOR - REMOVAL, SEAT BACK PANEL .........23-134
SECOND ROW INBOARD - 50/50 BENCH - INSTALLATION, SEAT BELT BUCKLE ....8O-38
SECOND ROW INBOARD - 50/50 BENCH - REMOVAL, SEAT BELT BUCKLE ........8O-37
SECTION IDENTIFICATION AND INFORMATION - DESCRIPTION ........8W-01-6
SECURITY - DESCRIPTION, VEHICLE THEFT .............................. 8Q-1
SECURITY - OPERATION, VEHICLE THEFT . . 8Q-1SECURITY SYSTEM - DIAGNOSIS AND
TESTING, VEHICLE THEFT ..............8Q-3
SELF-DIAGNOSTICS - DIAGNOSIS AND TESTING ............................ 8J-2
SENDING UNIT / SENSOR - DESCRIPTION, FUEL LEVEL .............14-5
SENDING UNIT / SENSOR - INSTALLATION, FUEL LEVEL .............14-6
SENDING UNIT / SENSOR - OPERATION, FUEL LEVEL .......................... 14-5
SENDING UNIT / SENSOR - REMOVAL, FUEL LEVEL .......................... 14-5
SENSE - PCM INPUT - OPERATION, IGNITION ........................... 8E-14
SENSITIVE DEVICES - STANDARD PROCEDURE, ELECTROSTATIC
DISCHARGE (ESD) .................8W -01-8
SENSOR - 2.4L - DESCRIPTION, ENGINE COOLANT TEMPERATURE ...............7-21
SENSOR - 2.4L - INSTALLATION, ENGINE COOLANT TEMPERATURE ...............7-21
SENSOR - 2.4L - REMOVAL, ENGINE COOLANT TEMPERATURE ...............7-21
SENSOR - 3.3/3.8L - DESCRIPTION, ENGINE COOLANT TEMPERATURE ........7-21
SENSOR - 3.3/3.8L - INSTALLATION, ENGINE COOLANT TEMPERATURE ........7-23
SENSOR - 3.3/3.8L - REMOVAL, ENGINE COOLANT TEMPERATURE ...............7-21
SENSOR - AWD - INSTALLATION, REAR WHEEL SPEED ........................ 5-92
SENSOR - AWD - REMOVAL, REAR WHEEL SPEED ........................ 5-92
SENSOR - DESCRIPTION, AMBIENT TEMP ............................. 8M-12
SENSOR - DESCRIPTION, BATTERY TEMPERATURE ...................... 8F-24
SENSOR - DESCRIPTION, BELT TENSION . . 8O-8
SENSOR - DESCRIPTION, CAMSHAFT POSITION ............................ 8I-4
SENSOR - DESCRIPTION, CRANKSHAFT POSITION .......................... 14-29
SENSOR - DESCRIPTION, ENGINE SPEED . 14-30
SENSOR - DESCRIPTION, EVAPORATOR TEMPERATURE ...................... 24-26
SENSOR - DESCRIPTION, FUEL LEVEL SENDING UNIT ....................... 14-5
SENSOR - DESCRIPTION, HEATED SEAT . . 8G-13
SENSOR - DESCRIPTION, IMPACT .......8O-18
SENSOR - DESCRIPTION, INFRARED TEMPERATURE ...................... 24-28
SENSOR - DESCRIPTION, INLET AIR TEMPERATURE ...................... 14-34
SENSOR - DESCRIPTION, KNOCK .........8I-8
SENSOR - DESCRIPTION, MAP ..........14-34
SENSOR - DESCRIPTION, O2 ...........14-36
SENSOR - DESCRIPTION, PARK ASSIST . . . 8B-6
SENSOR - DESCRIPTION, PINCH ........8N-17
SENSOR - DESCRIPTION, SEAT WEIGHT BLADDER & PRESSURE ...............8O-43
SENSOR - DESCRIPTION, THROTTLE POSITION .......................... 14-40
SENSOR - DESCRIPTION, TRANSMISSION RANGE ........21-130,21-281
SENSOR - DIAGNOSIS AND TESTING, TIRE PRESSURE ..................... 22-11
SENSOR - FWD - INSTALLATION, REAR WHEEL SPEED ........................ 5-93
SENSOR - FWD - REMOVAL, REAR WHEEL SPEED ........................ 5-93
SENSOR - INPUT - DESCRIPTION, SPEED ...................... 21-120,21-271
SENSOR - INPUT - INSTALLATION, SPEED ...................... 21-121,21-272
SENSOR - INPUT - OPERATION, SPEED . 21-120, 21-271
SENSOR - INPUT - REMOVAL, SPEED . . . 21-121, 21-272
SENSOR - INSTALLATION, FRONT WHEEL SPEED ........................ 5-92
SENSOR - INSTALLATION, FUEL LEVEL SENDING UNIT ....................... 14-6
SENSOR - INSTALLATION, IMPACT ......8O-21
SENSOR - INSTALLATION, PARK ASSIST . . . 8B-6
SENSOR - INSTALLATION, PINCH ........8N-18
SENSOR - INSTALLATION, TRANSMISSION RANGE ........21-131,21-282
SENSOR - OPERATION, AMBIENT TEMP . . 8M-12
28 INDEXRS
Description Group-Page Description Group-Page Description Group-Page