display Citroen BERLINGO 2017 2.G Owner's Guide

 117
Berlingo2VP_en_Chap05_Securite_ed02-2016
REVERSING CAMERA
The reversing camera is activated
automatically when reverse gear is
engaged.
The image is displayed in the touch
screen  tablet.
The reversing camera function may be
completed
  with   parking   sensors.
The reversing camera cannot in
any circumstances be a substitute
for vigilance on the part of the
driver. High pressure jet washing
When washing your vehicle, do
not direct the lance within 30 cm of
the
  camera   lens.
The superimposed representation of
guide
  lines   helps   with   the   manoeuvre.
They
  are   represented   by   lines   marked  
"on the ground" and do not allow the
position of the vehicle to be determined
relative

  to   tall   obstacles   (for   example:  
other

  vehicles,   ...).
Some deformation of the image is
normal. The blue lines represent the general
direction of the vehicle (the difference
corresponds to the width of your
vehicle
  without   the   mirrors).
The red lines represent a distance of
about 30 cm beyond the edge of your
vehicle's
  rear   bumper.
The green lines represent distances of
about 1 and 2 metres beyond the edge
of
  your   vehicle's   rear   bumper.
The turquoise blue curves represent
the
  maximum   turning   circle.
Opening the tailgate causes the
display
  to   disappear.
Clean the reversing camera regularly
using
  a   soft,   dry   cloth.
Parking sensors
SAFETY
5

123
Berlingo2VP_en_Chap05_Securite_ed02-2016
Driving safely
Operation
When your vehicle is too close to or
approaches the vehicle ahead too
quickly  the   system   automatically  
applies

  the   brakes   to   avoid   a   collision.
You are then alerted by the display of a
message.
The
  brake   lamps   on   your   vehicle   come  
on

  to   warn   other   road   users.
The collision can be avoided
automatically if the difference in
speed
between your vehicle and the
vehicle ahead does not exceed 9 mph
(15
  km/h).
Above this threshold, the system will
do what is possible to avoid or reduce
the accident by lowering the speed of
impact.
The
  automatic   braking   may   bring  
the vehicle to a complete stop if the
situation

  requires   it.
In this case, the vehicle is held
stationary temporarily (for about
1.5 seconds)
  to   allow   the   driver   to   take  
back

  control   by   pressing   the   brake  
pedal. The triggering of the system may
cause the engine to stall, unless
the driver depresses the clutch
pedal

  quickly   enough   during   automatic  
braking.
During

  automatic   braking,   the  
driver can always obtain a higher
rate of deceleration than that
controlled by the system, by pressing
firmly

  on   the   brake   pedal.
After an impact, the system is
automatically
  put   out   of   service:   it  
no

  longer   operates.
You must go to a CITROËN dealer or a
qualified
  workshop   to   have   the   system  
made

  operational   again.
Operating limits
The system only detects vehicles that
are stationary or moving in the same
direction  as   your   vehicle.
It does not detect small vehicles
(bicycles, motorcycles),
pedestrians or animals, nor non-
reflective
  stationary   objects.
The system is not triggered or is
interrupted
  if   the   driver:
-

accelerates strongly
-


or turns the steering wheel
suddenly

  (avoiding   manoeuvre).
In
  difficult   weather   conditions   (very  
heavy

  rain,   snow,   fog,   hail...),  
braking

  distances   increase,   which  
can reduce the ability of the system to
avoid

  a   collision.
The driver must therefore remain
particularly
  vigilant.
Never leave accumulations of
snow
  or   any   object   projecting  
above the bonnet or in front of
the

  roof:   this   might   fall   into   the   field   of  
vision of the sensor and generate a
detection.
SAFETY
5

124
Berlingo2VP_en_Chap05_Securite_ed02-2016
Deactivation
The system is deactivated in the
vehicle  configuration   menu,   accessible  
with

  the   ignition   on.
Its state is memorised when the
ignition
  is   switched   off.
When the system is deactivated,
a message is displayed every
time the ignition is switched on,
to warn
  you. With the monochrome screen C
F

Press the
MENU button for access
to
  the   main   menu.
F

Select "
Personalisation-
Configuration".
F

Select "
Define vehicle
parameters".
F

Select "
Driving assistance".
F

Select "
Automatic emergency
braking: OFF" or "Automatic
emergency braking: ON".
F

Press the "
7" or "8" button to
check
  or   uncheck   the   box   and  
activate or deactivate the system
respectively

.
F

Press the "
5" or "6" button, then
the OK button to select the "OK"
box
  and   confirm   or   the   Back button
to
  cancel.With the touch screen tablet
F
Press the "MENU"   button.
F Select the " Driving   "   menu.
F

In the secondary page, select
"

Vehicle settings".
F

Select the "
Driving assistance"
tab.
F
 
Check
  or   uncheck   the   "Auto
emergency braking" box to
activate
  or   deactivate   the   system.
F
 
Confirm.
Driving safely

125
Berlingo2VP_en_Chap05_Securite_ed02-2016
Driving safely
Operating faults
Sensor fault
The operation of the laser sensor may
suffer interference from accumulations
of  dirt   or   misting   of   the   windscreen.  
In this case you are warned by the
display

  of   a   message.
Use the windscreen demisting
and regularly clean the area of the
windscreen
  in   front   of   the   sensor.
Do
  not   stick   or   otherwise   fix   any  
object

  on   the   windscreen   in   front  
of

  the   sensor. System fault
In the event of a malfunction of the
system, you are warned by an audible
signal and the display of the message
"Automatic braking system fault".
Have
  the   system   checked   by   a  
CITROËN

  dealer   or   a   qualified  
workshop.In the event of an impact to
the windscreen at the sensor

,
deactivate the system and contact
a
  CITROËN   dealer   or   a   qualified  
workshop 

to  
have
 
your
 
windscreen
 
replaced.
Never

  try   to   remove,   adjust   or   test  
the

  sensor.
Only a CITROËN dealer or a
qualified
  workshop   is   able   to   work  
on

  the   system.
When towing a trailer or when the
vehicle is being towed, the system
must
  be   deactivated.
SAFETY
5

158
Berlingo2VP_en_Chap07_Verification_ed02-2016Berlingo2VP_en_Chap07_Verification_ed02-2016
Cooling system
Only use the fluid recommended by the manufacturer.
Otherwise,
  you   risk   seriously   damaging  
your

  engine.
When the engine is warm, the
temperature of the coolant is controlled
by
  the   engine   fan.  
As
  this   fan   can  
operate

  with   the   ignition   key   removed  
and because the cooling system is
pressurised, wait for at least one hour
after the engine has stopped before
carrying

  out   any   work.
Slacken
  the   cap   by   1/4   of   a   turn   to  
release the pressure to prevent any
risk

  of   scalding.   When   the   pressure  
has dropped, remove the cap and top
up

  the   level   with   coolant.
If
  fluid   has   to   be   added   frequently,  
this indicates a fault which must be
checked

  by   a   CITROËN   dealer   as  
soon

  as   possible.
Power steering fluid level
The vehicle must be parked on level ground  with   the   engine   cold.   Unscrew  
the cap integrated with the gauge and
check

  the   level   which   must   be   between  
the

  MIN   and   MAX   marks. In
  order   to   regenerate   the   filter,   you  are advised to drive at a speed higher
than
  40   mph   (60   km/h)   for   at   least   five  minutes as soon as possible, when
traffic
  conditions   permit   (until   the  
message disappears and the service
warning

  lamp   goes   off).
During regeneration of the particle
emission
  filter,   the   noise   of   a   relay  
operating may be heard under the
dashboard.
If the message is still displayed and
if the service warning lamp remains
on, contact a CITROËN dealer or a
qualified

  workshop.
Topping up
The level must be between the MIN
and
 
MAX
 
marks
 
on
 
the
 
expansion
 
bottle.

 
If
 
more
 
than
 
1
 
litre
 
of
 
fluid
 
is
 
required to top up the level, have the
system

 
checked
 
by
 
a
 
CITROËN
 
dealer
 
or

 
a
 
qualified
 
workshop.
Screenwash level
For best quality cleaning and for your
safety, we would advise that you use
products   of   the   CITROËN   range.
For optimum cleaning and to avoid
freezing,
  this   fluid   must   not   be   topped  
up

  or   replaced   with   plain   water.
Capacity
  of   the   screenwash   reservoir:  
approximately

  3   litres.
Diesel additive level
(Diesel with particle
filter)
Topping up
This additive must be topped up by
a  CITROËN   dealer   or   a   qualified  
workshop

  without   delay.
Waste products
Avoid prolonged contact of used oil
with  the   skin.
Brake
  fluid   is   harmful   to   health   and  
very

  corrosive.
Do
  not   dispose   of   used   oil,   brake   fluid  
or coolant into drains or into the ground
but into the containers dedicated to this
use at a CITROËN dealer (France) or
an

  authorised   waste   disposal   site.
The minimum level of this additive
is indicated by lighting of the service
warning lamp, accompanied by an
audible signal and a message in the
screen.
When this occurs with the engine
running it is due to the start of
saturation
 
of
 
the
 
particle
 
filter
 
(exceptionally prolonged urban type
driving

 
conditions:
 
low
 
speed,
 
long
 
traffic

 
jams,
 
...).
Levels

165
Berlingo2VP_en_Chap07_Verification_ed02-2016Berlingo2VP_en_Chap07_Verification_ed02-2016
Good practice
While the quantity of AdBlue® in
the
 
additive
 
tank
 
is
 
sufficient,
 
no
 
information

 
is
 
displayed.
On
 
the
 
other
 
hand,
 
once
 
the
 
fluid
 
level drops to the quantity needed
for

 
a
 
range
 
of
 
1
 
500
 
miles
 
(2
 
400
 
km)  
driving, you are warned by dif

ferent
temporary signals (warning lamp,
message,
 
audible
 
signal).
As more miles are covered, these
signals intensify and the message
becomes
 
permanent.
When the AdBlue
® tank is empty, restarting
 
becomes   impossible.
It is strongly recommended that you
do not wait for the successive alerts
before topping-up the AdBlue
® additive,
but
 
do
 
this
 
as
 
soon
 
as
 
possible.
Filling the AdBlue® tank
For light vehicles, 5 or 10 litre
containers
 
and
 
1.89
  litre  
(1/2 US gallon)

 
bottles   are   available  
from CITROËN dealers, until they are
equipped

with AdBlue
® delivery pumps.
If
 
you
 
want
 
to
 
fill
 
the
 
AdBlue® tank yourself, ensure that you have a
suitable
 
filler
 
pipe,
 
which
 
may   or   may  
not be supplied with the additive
container

.
CHECKS
7
AdBlue®

166
Berlingo2VP_en_Chap07_Verification_ed02-2016Berlingo2VP_en_Chap07_Verification_ed02-2016
Range indicators
Rules on the display of alertsFor more information on the
displays and warning lamps, refer
to chapter 3, "Instruments and
controls"
  section. Range greater than 1 500 miles
(2 400 km)
No
  information   displayed.
Once   the   1   500   miles   (2   400   km)  
threshold is reached, the UREA


warning lamp comes on temporarily
and the remaining range message is
displayed.
The alert is repeated every 200 miles
(300
  km)   until   the   next   threshold   is  
reached.
Every time the ignition is switched
on, the alert is given, together with an
audible

  signal.
Remaining range less than
1
500 miles (2 400 km) and greater
than 350 miles (600 km)
Driving range
With
  the   touch   screen   tablet:
If the range is greater than 3 100 miles
(5
  000   km),   a   range   value   is   not   given.
Press this button to display
the
  information.
-

select the "Driving
assistance" menu,
-


select "Diagnostic",
-

 
select
  CHECK.
Different levels of alert are triggered
according to the remaining driving
range threshold
You will be informed as each mileage
threshold is reached and the alerts will
change
  from   temporary   to   permanent.
-

The 1st is triggered at a remaining
driving range of 1 500 miles
(2
 
400
  km).
-

The 2nd is triggered at a remaining
driving range of 350 miles
(600
 
km).
-

Up to 0 miles, at which point it will
be impossible to restart the engine
after

 
a
 
stop.
AdBlue®

168
Berlingo2VP_en_Chap07_Verification_ed02-2016Berlingo2VP_en_Chap07_Verification_ed02-2016
Fault confirmed
In addition to the previous signals,
the  UREA
 
warning   lamp   flashes   and  
the remaining range allowed will be
displayed

  in   miles   (kilometres).
The alert will be repeated every
30
seconds with an update of the
driving range in steps of 30 miles
(50 km).
Go
  to   a   CITROËN   dealer   or   a   qualified  
workshop

  as   soon   as   possible.
You
  risk   not   being   able   to   start   the  
engine.
Starting prevented, having
covered the 650 miles (1 100 km)
At each attempt at starting, the alert is
activated and the message "Emissions
fault:

  Starting   prevented"   is   displayed.Refilling / Topping-up the
AdBlue®
Precautions to take
Use only AdBlue ® that meets the
ISO
 
22241
 
standard.
The AdBlue
® fluid is an urea-based solution.
This
 
fluid
 
is
 
non-flammable,   colourless  
and

 
odourless.
To
 
be
 
kept
 
in
  a   cool   area.
Containers (5 or 10 litres) and
bottles (1.89 litres) of AdBlue
®
Please check the use-by date.
Read   the   instructions   on   the   label.
Ensure that you have a suitable
filler
  pipe,   which   may   or   may   not   be  
supplied

  with   the   container. In
  the   event   of   an   overflow,   wipe  
around

  the   filler   mouth   using   a  
damp

  cloth.
If any AdBlue
® fluid is split or splashed on to you, wash immediately with cold
water or wipe yourself with a clean
damp
 
cloth.
If
 
the
 
fluid
 
has
  crystallised,   clean   it   off  
using

 
a
 
sponge   and   hot   water.
To
 
facilitate   filling,   an   adaptor   is  
available

 
from   CITROËN   dealers.
AdBlue®

203
Berlingo2VP_en_Chap10a_SMEGplus_ed02-2016
7-inch touch screen tablet
GPS satellite navigation - Multimedia audio - Bluetooth® telephone
Contents
First steps
2 04
Steering mounted controls
20

6
Menus
 2

07
Navigation


208
Navigation - Guidance
2

16
Traffic
 2

20
Radio Media

2
22
Radio

2
28
DAB (Digital Audio Broadcasting) radio

2
30
Media
2

32
Settings


234
Connected services
2

42
MirrorLink
TM 2 42
CarPlay® 246
T
elephone
2
48
Frequently
  asked   questions  
2
56
The system is protected in such a way that it will only operate in
your
 
vehicle. As a safety measure, the driver should only carry out operations
which
 
require
 
prolonged
 
attention   while   the   vehicle   is   stationary.
The display of an energy economy mode message signals that
electrical
 
systems
 
operating
 
are   going   into   standby.
Refer
 
to
 
the
 
energy
 
economy   mode   section.
Audio and Telematics
TECHNOLOGY on BOARD
10

204
Berlingo2VP_en_Chap10a_SMEGplus_ed02-2016
First steps
Use the buttons above the touch screen tablet
for access to the menu carousel, then press the
virtual  buttons   in   the   touch   screen   tablet.
Each menu is displayed in one or two pages
(primary
  page   and   secondary   page).
Secondary page
Primary page In very hot conditions, the system may
go into stand-by (screen and sound
completely off) for a minimum period of
5
 m

inutes.
Audio and Telematics