spare wheel CITROEN C-ELYSÉE 2023 User Guide

85
In the event of a breakdown
8Depending on engine, the spare wheel
may be a standard steel or 'space-saver'
wheel (BlueHDi 100).
Removing the spare wheel

â–º Unclip the tool storage box (standard spare
wheel).
â–º

Slacken the central nut.
â–º


Remove the fastening device (nut and bolt).
â–º


Lift the spare wheel towards you from the
rear

.
â–º

T
ake the wheel out of the boot.
Putting the spare wheel back in place
The punctured wheel cannot be put under the boot floor.


â–º Put the spare wheel back in place in its
housing.
â–º

Slacken the nut on the bolt by a few turns.
â–º


Position the fastening device (nut and bolt) in
the middle of the wheel.
â–º


T
ighten the central nut sufficiently to retain
the wheel correctly.
â–º

Put the tool box back in place in the middle of
the wheel and clip it in place.
Removing a wheel
Parking the vehicle
Immobilise the vehicle where it does
not obstruct traffic: the ground must be level,
stable and non-slippery.
With a manual gearbox, engage first gear
to lock the wheels, apply the parking brake,
unless it is set to automatic mode, and switch
off the ignition.
With an automatic gearbox, select mode

P

to lock the wheels, apply the parking brake,
unless it is set to automatic mode, and switch
off the ignition.
Check that the parking brake indicator lamps
on the instrument panel are on fixed.
The occupants must get out of the vehicle
and wait where they are safe.
If necessary, place a chock under the wheel
diagonally opposite the wheel to be changed.
Never go underneath a vehicle raised using a
jack; use an axle stand.
Wheel with wheel trim
When removing the wheel , first remove
the wheel trim by pulling at the valve aperture
using the wheelbrace.
When refitting the wheel , refit the wheel
trim, starting by placing its aperture in line
with the valve and then pushing it into place
all round its edge with the palm of your hand.

86
In the event of a breakdown

â–º Remove each wheel bolt cover using the
tool 3 (alloy wheels).
â–º

Slacken the other bolts using the
wheelbrace


1
only.


â–º Place the foot of jack 2 on the ground and
ensure that it is directly below the front A or
rear
B jacking point on the underbody, whichever
is closest to the wheel to be changed.


â–º Extend jack 2 until its head comes into
contact with jacking point A or B; contact area A
or B on the vehicle must be properly inserted
into the central part of the head of the jack.
â–º

Raise the vehicle until there is sufficient
space between the wheel and the ground to
easily admit the spare (not punctured) wheel.
Ensure that the jack is stable. If the
ground is slippery or loose, the jack may
slip or collapse - risk of injury!
Take care to position the jack strictly at
one of the jacking points

A
or B under the
vehicle, ensuring that the head of the jack is
centred under the contact area on the vehicle.
Otherwise, there is a risk of damage to the
vehicle and/or of the jack collapsing - risk of
injury!


â–º Remove the bolts and store them in a clean
place.
â–º

Remove the wheel.
Fitting a wheel
Fitting a steel or "space-saver" type
spare wheel
If the vehicle is fitted with alloy wheels, the
washers A do not make contact with the steel
or "space-saver" type spare wheel. The wheel
is held in place by the conical contact surface
B of each bolt.


â–º Fit the wheel on the hub.
â–º Screw in the bolts by hand as far as possible.
â–º

Pre-tighten the bolts using the wheelbrace

1

only.

87
In the event of a breakdown
8

â–º Lower the vehicle again fully.
â–º Fold jack 2 and remove it.


â–º Tighten the bolts using the wheelbrace 1 only.
â–º Refit the bolt covers to each of the bolts
(depending on equipment).
â–º

Store the tools.
After changing a wheel
Store the punctured wheel in the boot or,
depending on version, remove the central cover
first to store it beneath the floor in place of the
spare wheel.
With a non-standard or 'space-saver'
spare wheel
Do not exceed the maximum authorised
speed of 50 mph (80 km/h) or the maximum
distance of 50 miles (80 km).
Driving with more than one spare wheel of
this type is prohibited.
The wheel trim from the replaced wheel must
not be refitted.
Visit a CITROËN dealer or a qualified
workshop.
Have the tightening of the spare wheel's bolts
and its tyre pressure checked.
Have the punctured tyre examined. After
inspection, the technician will advise you on
whether the tyre can be repaired or if it must
be replaced.
Changing a bulb
In some weather conditions (e.g. low
temperature or humidity), misting on the
internal surface of the glass of the headlamps
and rear lamps is normal, and will disappear
after the lamps have been on for a few
minutes.
Never look too closely at the light beam
of LED technology lamps - risk of serious
eye injury!


The headlamps have polycarbonate lenses with a protective coating:
–

Do not clean them with a dry or abrasive
cloth, nor with detergent or solvent
products.
–


Use a sponge and soapy water or a pH
neutral product.
–


When using a high-pressure washer on
persistent marks, do not keep the lance
directed towards the headlamps, lamps or
their edges for too long, so as not to damage
their protective coating and seals.
Changing a bulb must only be done with
the ignition off and after the headlamp /

156
Alphabetical index
Stay, engine bonnet 76
Steering mounted controls,
audio

102, 113, 126
Steering wheel (adjustment)

25
Stickers, customising

82
Stopping the vehicle

53–54, 57
Stop & Start

16, 27, 29, 58–60, 69, 75, 79, 95
Storage

30–31
Sunshine sensor

26
Sun visor

30
Switch, ignition

53–54
Synchronising the remote control

20
T
Tables of engines 98–99
Tank, fuel
69–70
Technical data

98–99
Telephone

107, 120–121, 140–143
Third brake lamp

91
Time (setting)

14, 122, 145
TMC (Traffic info)

132
Tools

83, 84
Topping-up AdBlue®

72
Top Tether (fixing)

47
Total distance recorder

13
Towbar

74
Towed loads

97
Towing

95–96
Towing another vehicle

96
Towing the vehicle

95–96
Traction control (ASR) 38–39
Traffic information (TA)
103
Traffic information (TMC)

132
Trailer

74, 98–99
Trajectory control systems

38
Triangle, warning

83
Trip computer

14–16
Tyres

80, 101
Tyre under-inflation detection

60–62
U
Under-inflation (detection) 60
Unlocking
17
Unlocking from the inside

18
Unlocking the boot

17
Unlocking the doors

18–19
Updating the date

123, 145
Updating the time

122, 145
USB

104, 117–118, 139
V
Vehicle data recording and privacy 149
Ventilation
26–29
Voice commands

128–130
W
Warning and indicator lamps 7
Warning lamp, driver's
seat belt not fastened

40
Warning lamps

7
Warning lamp, seat belts

40
Warnings and indicators

7–8
Washing

63
Washing (advice)

81–82
Weights

97
Wheel, spare

80, 83–85
Windscreen, bottom of heated

29
Windscreen, heated

29
Wiper blades (changing)

35–36
Wipers

35