warning Citroen C3 2013 2.G Owner's Guide

1
Monitoring
37
Engine oil level indicator

This information is displayed for a few seconds
when the ignition is switched on, after theservice information.
Oil level correct
This is indicated by the flashing of "OIL", linked with the ser vice warning lamp, accompanied
by an audible signal and a message in the
multifunction screen.
If the low oil level is confirmed by a check using
the dipstick, the level must be topped up to prevent damage to the engine.
Oil level low

This is indicated by the flashing of "OIL--" . Contact a CITROËN dealer or a qualified
workshop.

Oil level indicator fault

Dipstick


There are 2 marks on the
dipstick:


- A= max; never exceed this
level (risk of damage to the engine), -B= min; top up the level via
the oil filler cap, using thegrade of oil suited to your engine. R
efer to the "Checks" section to locate the
dipstick and the oil filler cap on your engine.

The level shown will only be correctif the vehicle is on level ground and
the engine has been off for more than 30 minutes.

2
Multifunction screens
43







Monochrome screen A

This displays the following information:


- time,

- date,

- ambient temperature
(this flashes if there isa risk of ice),

- status of the doors and boot,

- audio sources
(radio, CD...),

- trip computer (refer to the "Instruments andControls" section).
Warning messages (e.g.: "Emission control system faulty") or information messages (e.g.:
"Boot open") may appear temporarily. Thesecan be cleared by pressing the "Back"button.
Controls
From the control panel of your Audio system,you can:)
press the "MENU"
button to gain access to
the main menu,)
press the " 
" or " " buttons to scroll
through the items in the screen,) press the "MODE"
button to change
the permanent application (date, audio source...),) press the "  " or " " buttons to change asetting value,)
press the "OK"button to confirm,or )
press the "Back"button to abandon the
operation in progress.



Main menu
)
Press the "MENU"
button to gain access
to the main menu
, then press the "  " or " " buttons to scroll through the variousmenus:
- radio-CD,
- vehicle configuration,
- options,
- displa
y settings,
- languages,
- units.)
Press the "OK"button to select the menurequired.


Radio-CD

With the Audio system switched on, once the
"Radio- CD" menu has been selected you canactivate or deactivate the functions linked
with use of the radio (RDS, REG), or the CD(introscan, shuffle, CD repeat).
For more information on the "Radio-CD"
application, refer to the Audio system par t of
the "Audio and Telematics" section.


Displays in the screen

Multifunction screens
46










Monochrome screen C
This displays the following information:
- time,
- date,
- ambient temperature (this flashes if there isa risk of ice),
- status of doors and boot,
- audio sources (radio, CD, USB por t / auxiliary socket etc.),
- trip computer (refer to the "Instruments andcontrols" section).
Warning messages (E.g. "Emissions controlsystem faulty") or information messages (E.g.: Automatic headlamps active") may appear temporarily. These can be cleared bypressing the "Back"
button.


Controls

From your Audio system control panel, you can: )
press the "MENU"
button to gain access to
the main menu,)
press the " " or " " buttons to scroll
through the items in the screen,
) press the "MODE"button to change the
permanent application (trip computer, audiosource...), ) press the " 
" or " 
" buttons to change a setting value, )
press the "OK"button to confirm,
or ) press the "Back"button to abandon theoperation in progress.

Main menu
)
Press the "MENU"button to gain access to
the main menu
:


- audio functions,

- the trip computer,

- personalisation-confi
guration,

- telephone (hands-free kit). )
Press the "  " or " " buttons to select the
menu required, then confirm by pressingthe "OK"button.



"Au d i o f u n c t i o n s"
menu

With the Audio system switched on, once this menu has been selected you can activateor deactivate the functions linked with use
of the radio (RDS, REG, RadioText), the CD (introscan, shuffle, CD repeat) or the MP3 player (USB por t / auxiliary socket).
For more information on the "Audio functions"
application, refer to the Audio system part of
the "Audio and Telematics" section.
Displays in the screen

2
Multifunction screens
47
"Trip computer" menu
Once this menu has been selected, you can consult information concerning the status of the
vehicle (warnings log, status of functions, etc.)

Alert log

This summarises the active warning messages,
displaying them in succession in themultifunction screen.
)
In the "Trip computer"
menu, select one
of the following applications:
) Press the "MENU"
button to gain access to
the general menu.) Press the arrows, then the "OK"
button to select the "Trip computer"menu.
Status of functions
This summarises the status (active or inactive)of the vehicle's functions.
Enter distance to destination
This allows you to enter an approximate
distance until your final destination.

Multifunction screens
50













16/9 colour screen (eMyWay)
It displays the following information automatically and directly:
- time,
- date,
- altitude,
- ambient temperature
(the value displayed
flashes if there is a risk of ice),
- check of the doors,
- warning and vehicle function status messages, displayed temporarily,
- audio functions,
- trip computer information (see the "Monitoring" section),
- satellite navigation system information.


Controls

To select one of the applications, from theeMyWay control panel:)
press the dedicated "RADIO"
, "MUSIC","NAV"
, "TRAFFIC", "SETUP"
or "PHONE"
button for access to thecorresponding menu, )
turn the knob to change the selection, )
press the knob to confirm the selection,
or ) press the "Back"button to abandon thecurrent operation and return to the previous
display.
For more in
formation on these applications, refer to the "Audio and Telematics" section or
to the specific user guide given to you with the other owner's documents.


"SETUP" menu
)Press the "SETUP"button to gain access
to the "SETUP"
menu. This allows you to select from the following functions:
- "System language",
- "Date and time",
- "Displa
y",
- "Vehicle",
- "Units",
- "S
ystem".


Displays in the screen

Comfort
56
With the heating /
ventilation s
ystem
)Put the temperature and air flow controls to
t
he dedicated marked position. )Put the air intake control to the "Exterior air intake" position (manual control to the right or electric control with indicator lamp off). )Put the air distribution control to the"Windscreen" position.
Front demist - defrost


These markings on the control panel indicate the control positions for rapid demisting or
defrosting of the windscreen and side windows.

With the manual air
conditioning system
)
Put the temperature and air flow controls to
t
he dedicated marked position.) Put the air intake control to the "Exterior air
intake" position
(manual control to the right or electriccontrol with indicator lamp off).) Put the air distribution control to the "Windscreen" position. )
Switch on the air conditioning by pressingthe "A/C"
button; the associated green
warning lamp comes on.

With Stop & Star t, when the demisting, air conditioning and air flow functionsare activated, STOP mode is not available.

4
Access
67

Folding the key
)First press this button to fold the key.
If you do not press the button when foldingthe key, there is a risk of damage to themechanism.

Anti-theft protection
Electronic engine immobiliser
The key contains an electronic chip which has a special code. When the ignition is switched
on, this code must be recognised in order for
startin
g to be possible.
This electronic engine immobiliser locks the
engine management system a few minutes after the ignition is switched off and prevents
starting of the engine by anyone who does not have the key.
In the event o
f a fault, you are
informed by illumination of this
warning lamp, an audible signal anda message in the screen.
Ignition switch


- Position 1: Stop

- Position 2: Ignition

- Position 3: Starting


Starting the vehicle
)
Inser t the key in the ignition switch.
The system recognises the star ting code.) Turn the key fully towards the dashboard toposition 3 (Starting).)
When the engine star ts, release the key.

Locating your vehicle
)
Press the closed padlock to locate your locked vehicle in acar park.
This is indicated b
y lighting of the cour tesylamps and flashing of the direction indicators for a few seconds. In this case,
your vehicle will not start; contact a CITROËN dealer as soon as possible.
Keep safely the label attached to the keys given
to you on acquisition of the vehicle.

Access
68
Remote control problem
Reinitialisation
)
Switch off the ignition. )
Turn the key to position 2 (Ignition on)
. )
Press the closed padlock immediately for a few seconds. )
Switch off the ignition and remove the key from the ignition switch.
The remote control is full
y operational again.


Changing the battery

Battery ref.: CR1620 / 3 volts.
If the batter
y is flat, you are informed by illumination of this warning lamp,
an audible signal and a message in
the multifunction screen.
)Unclip the casing using a coin at the notch. )Slide the flat battery out of its location.)Slide the new battery into its location
observing the original direction. )Clip the casing. )Reinitialise the remote control.


Switching the vehicle off


Key reminder

If the key is left in the ignition switch, an audible signal sounds when the driver's door is opened.

Do not attach any heavy objects to the key as this could weigh down on it when in the ignition switch and cause a fault. Followin
g disconnection of the vehicle battery,replacement of the remote control battery or
in the event of a remote control malfunction,you can no longer unlock, lock or locate your
v
ehicle. ) First of all, use the key in the lock to unlock or lock your vehicle.)
Then, reinitialise the remote control.
If the problem persists, contact a CITRO

Access
72











Doors
Opening
From out side
)After unlocking the vehicle using theremote control or the key, pull the door handle.



From inside
)
Pull the front door control to open the door;
this unlocks the vehicle completely.) Pull the rear door control to open the door;
this unlocks only the door opened.

Closing



- When the engine is running
, this
warning lamp comes on, accompanied
by a message in the multifunction screen for a few seconds,
When a door or the boot is not closed correctly:
- When the vehicle is movin
g
(speed higher than 6 mph (10 km/h)), this warning
lamp comes on, accompanied by anaudible signal and a message in the multifunction screen for a few seconds.

4
Access
75











Boot
)After unlocking the vehicle using theremote control or the key, pull the handleand raise the tailgate.
)
Lower the tailgate using the interior grab
handle.
-when the engine is running, this
warning lamp comes on, accompanied
b
y a message on the multifunctionscreen for a few seconds,
Tailgate release
Unlocking
)
Fold back the rear benchseat to gainaccess to the lock from inside the boot.)
Insert a small screwdriver into hole Aof thelock to unlock the tailgate.

I
f the tailgate is not closed correctly:

Opening Closing
-when the vehicle is moving
(speed above6 mph (10 km/h)), this warning lamp comes
on, accompanied by an audible signal and
a messa
ge on the multifunction screen for a few seconds.
System for mechanical unlocking of the boot
in the event of a battery or central locking
malfunction.