ABS Citroen C3 RHD 2013 2.G Owner's Manual

1
Monitoring
31
Warning lampis onCauseAction / Observations
Anti-lockBraking System(ABS)

fixed. The anti-lock braking system has a fault. The vehicle retains conventional braking.
Drive carefully at reduced speed and contact aCITROËN dealer or a qualified workshop without delay.
Dynamic stability control(ESP/ASR)

flashing.The ESP/ASR regulation is active. The system optimises traction and improves the
directional stability of the vehicle.

fix
ed. Unless it has been deactivated (button pressed and its indicator lamp
on) the ESP/ASR system has a fault. Have it checked b
y a CITROËN dealer or a qualified
workshop.
Engine autodiagnosis system
flashing. The engine management system hasa fault. Risk of destruction of the catalytic conver ter.
Have it checked by a CITROËN dealer or a qualified
workshop.

fix
ed. The emission control system has a
fault. The warning lamp should go off when the engine is started.
If it does not go off, contact a CITROËN dealer or qualified workshop without delay.
Braking

fixed, associated with
the STOP warning
lamp. The braking system fluid level is too
low. You must stop as soon as it is safe to do so.
Top up with brake fluid recommended by CITROËN.
If the problem persists, have the system checked by a
CITROËN dealer or a qualified workshop.

+
fixed, associated with
the
STOP and ABS
warning lamp. Th
e electronic brake force distribution(EBFD) system has a fault. You must stop as soon as it is safe to do so.
Have it checked by a CITROËN dealer or a qualified
workshop.

1
Monitoring
41





Monochrome screen C
16/9 colour screen
(eMyWay)


Information displays
)Press the button, located at the end of
the wiper stalk
, to display the various tripcomputer tabs in succession:- th
e current information tabwith:
●
the ran
ge,
●
the current fuel consumption,
●
the distance remaining to
be travelled or the Stop &Start time counter,
- the trip "1"
t
ab with:
●
the distance travelled,
●
the avera
ge fuelconsumption,
●
the average speed,for the first trip.
- the tri
p "2"tab with:
●
the distance travelled,
●
the avera
ge fuelconsumption,
●
the average speed,
for the second trip.

)
Pressing the button again returns you to
the normal display.
Trip zero reset
)
When the trip required is displayed, press
the button on the end of the wiper stalk for more than two seconds.
Tr ips "1"
and "2"are independent but their use
is identical.
For example, trip "1"can be used for daily
figures, and trip "2"for monthly figures.

Access
72
Locking the vehicle
w
ith exterior perimeter
protection only
If the alarm is triggered ten times insuccession, the eleventh time will result in it becoming inactive.If the indicator lamp in button A flashes rapidly, this indicates that the alarm was triggered during your absence. When the ignition is switched on, this flashingstops immediately.To a v o i d t r iggering the alarm whenwashing your vehicle, lock it using the key in the driver's door lock.


To be effective, this deactivation mustbe carried out each time the ignition is switched off.
Deactivation of the interior volumetric protection
)Switch off the ignition.
)Within ten seconds, press button Auntil
the indicator lamp is on continuously.)Get out of the vehicle.)Lock or deadlock the vehicle without delay using the locking button on the remote control.
The exterior perimeter protection alone remains
activated; the indicator lamp in button A flashes
once per second.
Reactivation of the interior volumetric protection
)Unlock the vehicle using the unlocking button on the remote control. )Relock the vehicle using the remote control.
The alarm is activated again with both types
o
f protection; the indicator lamp in button Aflashes once per second.

Tr iggering of the alarm


This is indicated by sounding of the siren
and flashing of the direction indicators for
approximatel
y thirty seconds.
After it has been triggered, both types of
protection are again operational.

Failure of the remote control
)
Unlock the vehicle using the key in the driver's door lock.)
Open the door; the alarm is triggered. )
Switch on the ignition; the alarm stops.




Locking the vehicle without
activating the alarm
)Lock or deadlock the vehicle using the key
in the driver's or passenger's door lock.




Malfunction


When the ignition is switched on, illumination of
the indicator lamp in button A
for ten secondsindicates malfunction with the siren.
Have it checked by a CITROËN dealer or a qualified workshop.


* Accordin
g to country.


Automatic activation *



2 minutes after the last door or the boot isclosed, the alarm is activated automatically.)To avoid triggering the alarm on entering
the vehicle, first press the unlocking buttonon the remote control.

7
Child safety
103
As a safety precaution, do not leave: - a child or children alone and unsuper vised in a vehicle, - a child or an animal in a vehicle which is exposed to the sun, with the windowsclosed, - the keys within reach of children inside the vehicle. To prevent accidental opening of the doors and rear windows, use the "Child lock". Take care not to open the rear windows bymore than one third.To protect young children from the rays of the sun, fit side blinds on the rear windows.
For optimum installation of the "forwards-facing" child seat, ensure that the back of the child seat is in contact with the back of thevehicle's seat and remove the head restraint.Ensure that the head restraint is stored or attached securely to prevent it from beingthrown around the vehicle in the event of sharp braking. Refit it if an adult uses theseating position.Children under the age of 10 must not travelin the "for wards-facing" position on the front passenger seat, unless the rear seats are already occupied by other children, cannotbe used or are absent. Deactivate the passenger airbag when a"rearwards-facing" child seat is installed onthe front seat. Other wise, the child would risk beingseriously injured or killed if the airbag wereto inflate.
Installing a booster seat
The chest par t of the seat belt must be
positioned on the child's shoulder without touching the neck.Ensure that the lap part of the seat belt passes correctly over the child's thighs.CITROËN recommends the use of a booster seat which has a back, fitted with a seat beltguide at shoulder level.
The incorrect installation of a child seat in a vehicle compromises the child's protection inthe event of an accident.Ensure that there is no seat belt or seat belt buckle under the child seat, as this could destabilise it. Remember to fasten the seat belts or the child seat harnesses keeping the slackrelative to the child's body to a minimum,even for short journeys.When installing a child seat using the seat belt, ensure that the seat belt is tightenedcorrectly on the child seat and that it securesthe child seat firmly on the seat of your vehicle. If your passenger seat is adjustable,move it for wards if necessary. At rear seating positions, always leave sufficient space between the front seat and: - a "rear wards facing" child seat, - the child's feet for a child seat fitted"forwards facing". To do this, move the front seat for wardsand, if necessary, move its backrest into theupright position.





Advice on child seats

Safety
110

Operating fault
You must stop as soon as it is safe to do so.

In either case, contact a CITROËN dealer or aqualified workshop. If this warnin
g lamp comes on,
accompanied by an audible signaland a message in the screen, it
indicates a malfunction of the anti-lock braking system which could
result in loss of control of the vehicle
when braking.
If this warnin
g lamp comes on,
together with the STOPand ABSwarning lamps, accompanied by an
audible signal and a message in the screen, it indicates a malfunction of
the electronic brake force distribution
which could result in loss of control of
the vehicle when braking.
Emergency braking assistance
System which, in an emergency, enables you
to obtain the optimum braking pressure morequickly, thus reducing the stopping distance.

Activation

It is triggered by the speed at which the brake pedal is pressed.
The effect of this is a reduction in theresistance of the pedal and an increase in
braking efficiency.
When replacing wheels (tyres and rims), ensure that they conform to the manufacturer's recommendations.

When braking in an emergency, press firmly without releasing the pressure.

















Braking assistance systems
Anti-lock braking system
and electronic brake force
distribution
Linked systems which improve the stability and manoeuvrability of your vehicle when braking,
in par ticular on poor or slippery surfaces.
Activation
The anti-lock braking system comes into
operation automatically when there is a risk of
wheel lock.
Normal operation of the ABS may make itself felt by slight vibration of the brake pedal.
When braking in an emergency, press very firmly without releasing the pressure. Group of supplementar
y systems which helpyou to obtain optimum braking in complete safety in emergency situations:
- anti-lock braking system (ABS),
- electronic brake force distribution (EBFD),
- emergency braking assistance (EBA).

Practical information
162
bulbs
)Remove the protective cover by pulling on
the tab.)Disconnect the bulb connector. )Spread the springs to release the bulb.)Remove the bulb and change it.
To r e f i t , c a r ry out these operations in reverse order.

Changing sidelamp bulbs
)
Remove the protective cover by pulling on
the tab. ) Pull the bulb holder pressing on the tabs on both sides. )
Pull the bulb and change it.
To r efit, carry out these operations in reverseorder.

Practical information
164
Rear lamps
1.Brake / sidelamps (P21/5W).2.Direction indicators (PY21W amber)3. Foglamp, right-hand side (PR21W red)Reversing lamp, left-hand side (P21W).
Changing bulbs
These four bulbs are changed from inside the boot: )spread the four tabs and remove the bulbholder,
)turn the bulb a quar ter of a turn and change it.
To r efit, carry out these operations in reverse order.
Take care to engage the lamp unit in its guides,
while keeping it in line with the vehicle.
) open the boot,)
remove the access flap from the
corresponding side trim panel,)
unscrew the butterfly nut securing the lamp unit, )
unclip the lamp unit connector, )
extract the lamp unit carefully pulling in its
middle towards the outside,
Amber or red bulbs, such as thosefor the direction indicators and rear foglamp, must be replaced by bulbs of the same rating and colour. The lamps on the tailgate are dummy units. They are there for aesthetic purposes only.

11
Practical information
171
Fuse N°RatingFunctions
F120 AEngine control unit supply, cooling fan unit control relay,multifunction engine control main relay, injection pump (Diesel).
F
215 AHorn.
F
310 AFront / rear wash-wipe.
F420 ADaytime running lamps, LED daytime running lamps.
F
515 ADiesel heater (Diesel), par ticle filter additive pump (Diesel), air
flow sensor (Diesel), fuel pump (1.1i and 1.4i), blow-by heater
and electrovalves (VTi).
F
610 A ABS/ESP control unit, secondary stop switch.
F710 AElectric power steering, automatic gearbox.
F
825 AStarter control.
F9
10 ASwitching and protection unit (Diesel).
F10
30 AFuel heater (Diesel), blow-by heater (1.1i, 1.4i and Diesel), fuel pump (VTi), injectors and ignition coils (petrol), electronic
thermostat and canister purge electrovalve (1.1i and 1.4i).
F1
140 AHeater blower.

Fuse table

Practical information
172
Fuse N°RatingFunctions
F1230 A Windscreen wipers slow / fast speed.
F13
40 A Built-in systems inter face supply (ignition positive).
F14
30 A Valvetronic supply (VTi).
F1
510 A Right-hand main beam headlamps.
F1
610 A
Left-hand main beam headlamps.
F17 15 A
Left-hand dipped beam headlamps.
F18 15 A
Ri
ght-hand dipped beam headlamps.
F1
915 A Oxygen sensors and electrovalves (VTi), electrovalves (Diesel),
EGR electrovalve (Diesel).
F20 10 A Pumps, electronic thermostat
(VTi), water in fuel sensor (Diesel).
F2
15 A Fan assembly control supply, ABS/ESP.

11
Practical information
173

Table of maxi-fuses
Fuse N°RatingFunctions
MF1*60 AFan assembly.
MF2*30 A ABS / ESP pump.
MF3 * 30 A ABS / ESP electrovalves.
MF4 * 60 ABuilt-in Systems Interface (BSI) supply.
MF5 * 60 ABuilt-in Systems Interface (BSI) supply.
MF6 *-Not used.
MF7 *80 ADashboard fusebox.
MF8 *
-Not used.

*

The maxi-fuses provide additional protection for the electrical systems. All work on the maxi-fusesmust be carried out by a CITROËN dealer or a qualified workshop.