rfn Citroen C4 2005 2.G Repair Manual

Downloaded from www.Manualslib.com manuals search engine 324
CLUTCH
GEARBOX
TRANSMISSION
TIGHTENING TORQUES: BE4/5 GEARBOX
Engines: RFN - RFK - 9HX - 9HY - 9HZ
Tightening torques (m.daN).
(1)Air vent hole : 1,5 ± 0,2
(2)Reverse gear rocker switch shaft fixing nut: 4,5 ± 0,2
(3) Differential housing fixing nut: 1,5 ± 0,2
(4)Screw fixing
(Ø M10)differential housing: 5 ± 0,5
(5)Speedometer drive support: 1,5 ± 0,2
(6)Screw fixing
(Ø M7)differential housing: 1,5 ± 0,2
(7)Drain plug : 3,5 ± 0,2
(8)Level plug: 2,2 ± 0,2
(9)Screw fixing gearbox housing/clutch housing: 1,3 ± 0,2
(10) Screw fixing 5th gear housing: 1,5 ± 0,2
(11)Reverse gear switch: 2,5 ± 0,2
B2CP3ZXD
C4
Angl.-t2-page306-360-2005 9/01/06 10:20 Page 324

Downloaded from www.Manualslib.com manuals search engine 325
CLUTCH
GEARBOX
TRANSMISSION
TIGHTENING TORQUES: BE4/5 GEARBOX
Engines: RFN - RFK - 9HX - 9HY - 9HZ
Tightening torques (m.daN).
(12)Fork shaft stop screw: 1,5 ± 0,2
(13)Differential gearwheel fixing screw: 6 ± 0,5
(14)Bearing stop screw: 1,5 ± 0,2
(15)Secondary shaft nut: 6,5 ± 0,5
(16)Primary shaft nut: 7,3 ± 0,5
(17)Gear control support fixing screw: 1,5 ± 0,2
B2CP3ZZC
B2CP3ZYD
C4
Angl.-t2-page306-360-2005 9/01/06 10:20 Page 325

Downloaded from www.Manualslib.com manuals search engine 326
CLUTCH
GEARBOX
TRANSMISSION
TIGHTENING TORQUES: BE4/5 GEARBOX
Engines: RFN - RFK - 9HX - 9HY - 9HZ
Tightening torques (m.daN).
(18)Stop guide screw: 1,25 ± 0,2
(19)Speedometer fixing screw: 1,5 ± 0,2
(20) Gearbox support shaft nut : 6,5 ± 0,6
(21)Nuts fixing rubber support: 3 ± 0,2
(22) Gearbox rubber support shaft: 5 ± 0,5
(23)Screw M10fixing the engine/gearbox housing support: 6 ± 0,5
(24) Screws M10fixing the engine/gearbox housing support: 3 ± 0,3
B2CP401C
B2CP400C
C4
Angl.-t2-page306-360-2005 9/01/06 10:20 Page 326

Downloaded from www.Manualslib.com manuals search engine 327
CLUTCH
GEARBOX
TRANSMISSION
TIGHTENING TORQUES: BE4/5 GEARBOX
Engines: 6FZ - RFN - WJY - 8HX - 8HZ - 9HY - 9HZ - RHY - RHZ
T
ightening torques (m.daN).
(23)Clutch bearing guide (3 screws): 1,25 ± 0,2
(24)Clutch housing
(13 screws): 1,3 ± 0,2
(25)Primary shaft nut
(1 screw): 7,25 ± 0,5
(26)Secondary shaft nut
(1 screw): 6,5 ± 0,5
(27)Yoke retaining screw
(2 screws): 1,5 ± 0,2
(28)Differential gearwheel screw
(2 screws): 6,5 ± 0,5
Reverse gear switch (1 screw): 2,5 ± 0,3
(29)Differential housing
(4 screws): 5 ± 0,5
(30)Breather pipe: 1,7 ± 0,2
(31)Rear housing cover screws
(7 screws): 1,25 ± 0,2
(32)Top-up plug
(1 screw): 2,2 ± 0,2
(33) Differential housing screws
(4 screws): 1,25 ± 0,2
(34)Drain plug
(1 screw): 3,5 ± 0,3
B2CP3BRD
XSARA - XSARA PICASSO
Angl.-t2-page306-360-2005 9/01/06 10:20 Page 327

Downloaded from www.Manualslib.com manuals search engine 335
CLUTCH
GEARBOX
TRANSMISSION
BE4/5 GEARBOX CONTROLS
Engines: NFU - RFN - RFK - 9HX - 9HY - 9HZ
The gear selection and engagement cables have noadjustment.
Gear controls.
(1)Gear engagement ball-joint: Ø 10 mm
(2)Gear engagement control cable
(3)Gear control lever
(4)Gear selection control cable
(5)Gear selection ball-joint: Ø 10 mm
B2CP3ZOD
C4
Angl.-t2-page306-360-2005 9/01/06 10:20 Page 335

Downloaded from www.Manualslib.com manuals search engine 336
CLUTCH
GEARBOX
TRANSMISSION
BE4/5 GEARBOX CONTROLS
Engines: NFU - RFN - RFK - 9HX - 9HY - 9HZ
Length A (mm)
Gear engagement control cable643 ± 2
Length B (mm)
Gear selection control cable670 ± 2
NOTE:The gear engagement cable has a black colouridentification
on the sleeve stop at «a».
B2CP3Z1CB2CP3Z2C
C4
Angl.-t2-page306-360-2005 9/01/06 10:20 Page 336

Downloaded from www.Manualslib.com manuals search engine 337
CLUTCH
GEARBOX
TRANSMISSION
BE4/5 GEARBOX CONTROLS
Engines: NFU - RFN - RFK - 9HX - 9HY - 9HZ
Features.
Unlocking a sleeve stop:
- Press on the tabs of the clip (6)at «b», using a flat screwdriver.
- Disengage the sleeve stops from their supports by pulling upwards.
B2CP3Z3D
C4
Angl.-t2-page306-360-2005 9/01/06 10:20 Page 337

Downloaded from www.Manualslib.com manuals search engine 338
CLUTCH
GEARBOX
TRANSMISSION
BE4/5 GEARBOX CONTROLS
Engines: NFV - 6FZ - RFN - WJY - 8HX - 8HZ - 9HY - 9HZ - RHY - RHZ
(1)Gear control lever
(2)Gear engagement control cable (*)
(3) Gear selection control cable (*)
(4)Gear selection ball-joint Ø 10 mm
(5)Gear engagement ball-jointØ 10 mm
(6)Flexible insulating grommet through the bulkhead
(*) = These two cables cannot be separated.
B2CP3BWD
XSARA - XSARA PICASSO
Angl.-t2-page306-360-2005 9/01/06 10:20 Page 338

Downloaded from www.Manualslib.com manuals search engine 339
CLUTCH
GEARBOX
TRANSMISSION
CHECKS AND ADJUSTMENTS: BE4/5 GEARBOX CONTROLS
Principles of adjusting the gear controls.
WARNING: Cables should be adjusted each time the gearbox, gear controls or power unit are
removed.
Principles.
Lock the gear lever in neutral position, using tool: 9607-T.
Place the gearbox in neutral.
Couple the cables on the lever.
Fit the ball-joints on the gearbox lever.
Lock the cable lengths with the ball-joint locking keys.
WARNING: Do not use any tool to unclip the ball-joints.
To unlock the ball-joint, press at the centre «a», then pull the ball-joint upwards.
NOTE:Changing an individual ball-joint is possible as long as the locking key is removed.
Unclip at «b», using two small screwdrivers.
Engines: NFV - 6FZ - RFN - WJY - 8HX - 8HZ - 9HY - 9HZ - RHY - RHZ
XSARA - XSARA PICASSO
B2CP3BXC
B2CP3BYC
Angl.-t2-page306-360-2005 9/01/06 10:20 Page 339

Downloaded from www.Manualslib.com manuals search engine 340
CLUTCH
GEARBOX
TRANSMISSION
CHECKS AND ADJUSTMENTS: BE4/5 GEARBOX CONTROLS
Tools.
[1]Tool for positioning the gear lever: 9607-T
Adjustments.
WARNING: Cables should be adjusted each time
the gearbox, gear controls or power unit are
removed.
Inside the vehicle.
Remove the trim under the gear lever.
Lock the gear lever in neutral position, using tool [1].
Under the bonnet.
Remove the air filter assembly.
Unlock the ball-joint keys at «a».
Place the gear selection and control levers on neutral.
Lock the cable lengths with the ball-joint locking keys.Checks.
Remove the tool [1].
Check that all the gears engage without «tightness».
Check that the gear lever moves identically forwards
and backwards and to right and left.
If it does not, repeat the adjustment.
Refit the trim under the gear lever.
Refit the air filter assembly.
Adjusting the gear controls Engines: NFV - 6FZ - RFN - WJY - 8HX - 8HZ - 9HZ - 9HY - RHY - RHZ
XSARA - XSARA PICASSO
B2CP3C6CB2CP3C0C
Angl.-t2-page306-360-2005 9/01/06 10:20 Page 340