low beam CITROEN C4 2019 Owners Manual
[x] Cancel search | Manufacturer: CITROEN, Model Year: 2019, Model line: C4, Model: CITROEN C4 2019Pages: 317, PDF Size: 9.31 MB
Page 15 of 317

13
C4-cactus_en_Chap01_Instruments-de-bord_ed01-2016
Operation indicator lamps
If one of the following indicator lamps comes on, this confirms that the corresponding system has come into operation.
I t  may  be  accompanied  by  an  audible  signal  and  a  message  in  the  screen.
Left-hand
direction indicatorflashing with buzzer.The  lighting  stalk  is  pushed  down.
Right-hand
direction indicatorflashing with buzzer.The  lighting  stalk  is  pushed  up.
Sidelamps fixed. The
 lighting  stalk  is  in  the Â
"
Sidelamps"
 p
osition.
Dipped beam
headlamps fixed.
The
 lighting  stalk  is  in  the  "Dipped Â
b
eam  headlamps"  position.
Main beam
headlamps fixed.
The
 lighting  stalk  is  pulled  towards Â
yo
u. Pull
 the  stalk  to  return  to  dipped  beam  headlamps.
Front foglamps fixed. The
 front  foglamps  are  switched  on Â
u
sing  the  ring  on  the  lighting  control Â
st
alk. Turn
 the  ring  on  the  lighting  control  stalk  rear ward Â
t
wice  to  switch  off  the  front  foglamps.
For
Â
more
Â
information
Â
on
 the  lighting  controls,  refer  to  the  corresponding  section.
Warning / indicator lamp
StateCause Action / Observations
1
Instruments
Page 80 of 317

78
C4-cactus_en_Chap04_Eclairage-et-visibilite_ed01-2016
Lighting control
Main lighting
The various front and rear lamps of the vehicle are  designed  to  adapt  the  driver's  visibility Â
p
rogressively  according  to  the  climatic Â
c
onditions:
-
Â
s
idelamps,  to  be  seen,
-
Â
d
ipped  beam  headlamps  to  see  without Â
d
azzling
 o
ther
 d
rivers,
-
Â
m
ain  beam  headlamps  to  see  clearly  when Â
t
he  road  is  clear.
Additional lighting
Other lamps are provided to meet the requirements  of  particular  driving  conditions:
-
Â
a
 rear  foglamp,
-
Â
f
ront  foglamps  with  cornering  lighting,
-
Â
d
aytime  running  lamps  to  be  more  visible Â
d
uring  the  day,
-
Â
g
uide-me-home  lighting  to  facilitate  your Â
e
xit  from  the  vehicle,
-
Â
p
arking  lamps  as  vehicle  position  markers.
In
 the  event  of  the  failure  of  one  or  more Â
b
ulbs,  a  message  advises  you  to  check Â
t
he  lamp(s)  in  question.Travelling abroad
The design of the dipped beam headlamps  allows,  without  modification, Â
d
riving  in  a  country  that  drives  on  the Â
o
ther side of the road to the country in
which
 your  vehicle  was  sold.
Lighting and visibility
Page 83 of 317

81
C4-cactus_en_Chap04_Eclairage-et-visibilite_ed01-2016
In good or rainy weather, both day and  night,  the  front  foglamps  and  the Â
r
ear  foglamp  are  prohibited.  In  these Â
s
ituations,  the  power  of  their  beams Â
m
ay  dazzle  other  drivers.  They  should Â
o
nly  be  used  in  fog  or  snow.
In these weather conditions, it is your
responsibility
 to  switch  on  the  foglamps Â
a
nd  dipped  beam  headlamps  manually Â
a
s  the  sunshine  sensor  may  detect Â
s
ufficient  light.
Do
 not  forget  to  switch  off  the  front Â
f
oglamps  and  the  rear  foglamp  when Â
t
hey  are  no  longer  necessary.Switching off the lamps when
the ignition is switched off
On switching off the ignition, all of the lamps  turn  off  immediately,  except  for Â
d
ipped  beam  if  guide-me-home  lighting Â
i
s  activated.
Switching on the lamps
after the ignition is
switched off
To reactivate the lighting control, rotate the  ring  to  the  "0" position  -  lamps  off, Â
t
hen  to  the  desired  position.
On
 opening  the  driver's  door  a Â
t
emporary  audible  signal  warns  the Â
d
river  that  the  lighting  is  on.
The
 lamps,  with  the  exception  of  the Â
s
idelamps,  switch  off  automatically  after Â
a
 maximum  duration  of  thirty  minutes  to Â
p
revent  discharging  of  the  battery.
Direction indicators
F Left: lower  the  lighting  stalk  passing  the  p
oint  of  resistance.
F
Â
R
ight:  raise  the  lighting  stalk  passing  the Â
p
oint  of  resistance.
Three flashes of the direction
indicators
F Press briefly upwards or downwards, without  going  beyond  the  point  of Â
r
esistance;  the  direction  indicators  will Â
f
lash  3  times.
4
Lighting and visibility
Page 85 of 317

83
C4-cactus_en_Chap04_Eclairage-et-visibilite_ed01-2016
Parking lamps
Side markers for the vehicle by illumination of the  sidelamps  on  the  traffic  side  only.
F
Â
D
epending  on  version,  within  one  minute Â
o
f  switching  off  the  ignition,  operate  the Â
l
ighting  control  stalk  up  or  down  depending Â
o
n  the  traffic  side  (for  example:  when Â
p
arking  on  the  left;  lighting  control  stalk Â
u
pwards;  the  right  hand  sidelamps  are  on).
This
 is  confirmed  by  an  audible  signal  and Â
i
llumination  of  the  corresponding  direction Â
i
ndicator  warning  lamp  in  the  instrument  panel.
To
 switch  off  the  parking  lamps,  return  the Â
l
ighting  control  stalk  to  the  central  position.
Daytime running lamps / Sidelamps
(LEDs)
The light-emitting diodes (LEDs) come on automatically  when  the  engine  is  started.
In
 some  weather  conditions  (e.g.  low Â
t
emperature  or  humidity),  the  presence Â
o
f  misting  on  the  internal  sur face  of  the Â
g
lass  of  the  headlamps  and  rear  lamps Â
i
s  normal;  it  disappears  after  the  lamps Â
h
ave  been  on  for  a  few  minutes.They
 provide  the  following  functions:
-  D aytime  running  lamps  (lighting  control Â
s
talk  in  position  "0 " or " AUTO " with
adequate
 light  level).
-
Â
S
idelamps  (lighting  control  stalk  in Â
p
osition "AUTO"
 with  low  light  level  or Â
"
Sidelamps  only"  or  "Main  or  dipped  beam Â
h
eadlamps").The
 LEDs  are  brighter  when  operating Â
a
s  daytime  running  lamps.
4
Lighting and visibility
Page 87 of 317

85
C4-cactus_en_Chap04_Eclairage-et-visibilite_ed01-2016
Cornering lighting
With dipped or main beams, this system makes  use  of  the  beam  from  a  front Â
f
oglamp  to  illuminate  the  inside  of  a  bend, Â
w
hen  the  vehicle  speed  is  below  25  mph Â
(
approximately 40  km/h)  (urban  driving,  winding Â
r
oad,  intersections,  parking  manoeuvres...).With cornering l
ighting
Without cornering
 l
ighting
Switching on
This system starts:
-  w hen  the  corresponding  direction  indicator Â
i
s switched on,
or
-
Â
f
rom  a  certain  angle  of  rotation  of  the Â
s
teering
 w
heel.
Switching off
The system does not operate:
-  b elow  a  certain  angle  of  rotation  of  the Â
s
teering
 w
heel,
-
Â
a
bove  25  mph  (40  km/h),
-
Â
w
hen  reverse  gear  is  engaged.
4
Lighting and visibility
Page 122 of 317

120
C4-cactus_en_Chap06_conduite_ed01-2016
When towing
Distribution of loads
F Distribute the load in the trailer so that the heaviest  items  are  as  close  as  possible  to Â
t
he  axle  and  the  nose  weight  approaches Â
t
he  maximum  permitted  without Â
e
xceeding it.
Air density decreases with altitude, thus
reducing
 engine  per formance.  Above Â
1Â 0
00 metres,  the  maximum  towed  load  must Â
b
e  reduced  by  10 %  for  every  1 000  metres  of Â
al
titude.
For
 more  information  on  weights  (and  the Â
t
owed loads which apply to your vehicle) refer
to
 the  corresponding  section.
Side wind
F Take into  account  the  increased  sensitivity  t
o  side  wind.
Cooling
Towing a trailer on a slope increases the temperature  of  the  coolant.
As
 the  fan  is  electrically  controlled,  its  cooling Â
c
apacity  is  not  dependent  on  the  engine  speed.
F
Â
T
o  lower  the  engine  speed,  reduce  your Â
s
peed.
The
 maximum  towed  load  on  a  long  incline Â
d
epends  on  the  gradient  and  the  ambient Â
t
emperature.
In
 all  cases,  keep  a  check  on  the  coolant Â
t
emperature. F
Â
I
f  the  warning  lamp  and  the Â
S
TOP
Â
warning  lamp  come  on, Â
s
top the vehicle and switch off
the
 engine  as  soon  as  possible.
Braking
Towing a trailer increases the braking distance.
T o  avoid  overheating  of  the  brakes,  the  use  of Â
e
ngine  braking  is  recommended.
Ty r e s
F Check the  tyre  pressures  of  the  towing  v
ehicle  and  of  the  trailer,  observing  the Â
re
commended
 p
ressures.
Lighting
F Check the  electrical  lighting  and  signalling  o
n  the  trailer  and  the  hadlamp  beam  height Â
o
f  your  vehicle.
For
 more  information  on  adjusting  the Â
h
eadlamp  beam  height,  refer  to  the Â
c
orresponding
 s
ection.
The
 rear  parking  sensors  will  be Â
d
eactivated  automatically  if  a  genuine Â
C
ITROËN  towbar  is  used.
Driving
Page 199 of 317

197
C4-cactus_en_Chap08_En-cas-de-panne_ed01-2016
Changing a bulb
Front lamps
1. Daytime running  lamps  /  Sidelamps  (LE
Ds).
2.
 D
ipped  beam  headlamps  (H7).
3.
 M
ain  beam  headlamps  (H1).
4.
 D
irection  indicators  (PY21W).
5.
 F
ront  foglamps  (PS24W). In
 some  weather  conditions  (e.g.  low Â
t
emperature  or  humidity),  the  presence Â
o
f  misting  on  the  internal  sur face  of  the Â
g
lass  of  the  headlamps  and  rear  lamps Â
i
s  normal;  it  disappears  after  the  lamps Â
h
ave  been  on  for  a  few  minutes.
The  headlamps  are  fitted  with Â
p
olycarbonate  glass  with  a  protective Â
c
oating:
F
d
o not clean them using a dr y
or abrasive cloth, nor with a
detergent or solvent product,
F Â
u
se  a  sponge  and  soapy  water  or  a Â
p
H neutral product,
F Â
w
hen  using  a  high  pressure  washer Â
o
n  persistent  marks,  do  not  keep Â
t
he lance directed towards the
lamps  or  their  edges  for  too  long,  s
o  as  not  to  damage  their  protective  c
oating a nd sea ls.
Changing
 a  bulb  should  only  be  done Â
a
fter  the  headlamp  has  been  switched Â
o
ff  for  several  minutes  (risk  of  serious Â
b
urns).
F
D
o not touch the bulb directly with
your
 fingers,  use  a  lint-free  cloth.
It
 is  imperative  to  use  only  anti-
ultraviolet (UV) type bulbs to avoid
damaging
 t
he
 h
eadlamp.
Always replace a failed bulb with a
new
 bulb  with  the  same  type  and Â
s
pecification.
8
In the event of a breakdown
Page 209 of 317

207
C4-cactus_en_Chap08_En-cas-de-panne_ed01-2016
Dashboard fuses
The 2 fuseboxes are placed in the lower dashboard,  below  the  steering  wheel.Fuse
N° Rating
(A) Functions
F01 10Brake  pedal  (switch  2),  Stop  &  Start.
F02 5Headlamp  beam  height  adjuster,  additional  heater  (Diesel), Â
p
arking  sensors,  diagnostic  socket,  door  mirrors  (electric Â
a
djustment),  Grip  control.
F03 10Diesel  additive  pump,  electric  power  steering,  clutch  pedal  (
sw i tc h).
F04 5Rain
 and  sunshine  sensor.
F06 10Brake
 pedal  (switch  1),  diagnostic  socket.
F08 5
Top of steering column contacts with steering mounted controls.
F105Emergency  call  /  Assistance  call.
F12 5Stop
 &  Start,  ABS,  ESC.
F13 5Parking
 sensors,  reversing  camera.
F14 10Electronic
 gearbox,  switch  panel  (below  the  touch  screen Â
t
ablet),  air  conditioning,  touch  screen  tablet.
F16 1512
 volt  socket.
F18 20Radio.
Access to the fuses
F Unclip the  cover  by  pulling  at  top  left,  then  r
ight.
Left hand fusebox
8
In the event of a breakdown