ignition Citroen C4 CACTUS 2015 1.G Workshop Manual

171
C4-cactus_en_Chap09_info-pratiques_ed02-2014
1. Sealing
Repair procedure
Avoid removing any foreign bodies which   have   penetrated   into   the   tyre.F

U
ncoil the white pipe G  
f
ully.
F  
U
nscrew   the   cap   from   the   white   pipe.
F
C
onnect the white pipe to the valve of the
tyre   to   be   repaired.
F
 
S

witch   off   the   ignition.
F
T
urn the selector A to the
"sealant"
 p
osition.
F  
C
heck   that   the   switch   B is in
position "O" . F  
C
onnect   the   compressor's   electric   plug   to  
t

he   vehicle's   12   V   socket.
F  
S
tart   the   vehicle   and   leave   the   engine  
r

unning.
Take   care,   this   product   is   harmful   (e.g.
 e

thylene-glycol,   colophony...)   if   swallowed
 a
nd   causes   irritation   to   the   eyes.ke
ep this product out of the reach of
children. Do
  not   start   the   compressor   before  
c

onnecting   the   white   pipe   to   the   tyre  v
alve:   the   sealant   product   would   be  e
xpelled   through   the   pipe.
9
Practical information

194
C4-cactus_en_Chap09_info-pratiques_ed02-2014
FuseN° Rating
(A) Functions
F19 5Seat
  belt   unfastened   warning.
F20 5Airbags.
F21 5Instrument
  panel.
F22 30Locks.
F23 5Courtesy
  lamp.   map   reading   lamp.
F26 15Horn.
F27 15Front
  and   rear   screenwash.
F28 5Ignition
 s

witch.
F30 15Rear
  wiper.
Practical information

198
C4-cactus_en_Chap09_info-pratiques_ed02-2014
12 V battery
The battery is located under the bonnet.
F or   access   to   the   (+)   terminal:
F
 
r
elease   the   bonnet   using   the   interior   lever,  
t

hen   the   exterior   safety   catch,
F

r
aise the bonnet and secure it with its stay,
F

l
ift the plastic cover for access to
the
  (+)   terminal.
Access to the battery
Procedure for starting the engine using another battery or charging a discharged battery.
T he presence of this label, in particular
with
  the   Stop   &   Start   system,   indicates  
t

he use of a 12 V lead-acid battery with
special
 t

echnology
 a
nd
 s
pecification;
 t

he   involvement   of   a   CITROËN   dealer  
o

r   a   qualified   workshop   is   essential  
w

hen   replacing   or   disconnecting   the  
b

attery.
After
  refitting   the   battery,   the   Stop   &
 S

tart   system   will   only   be   active   after   a
 c

ontinuous   period   of   immobilisation   of   the
 v

ehicle, a period which depends on the
climatic
  conditions   and   the   state   of   charge
 o

f   the   battery   (up   to   about   8   hours).
Before doing any work
Immobilise the vehicle: apply the parking   brake,   put   the   gearbox   in  
n

eutral,   then   switch   off   the   ignition.
Check
  that   all   electrical   equipment   is  
s

witched   off.
Practical information

200
C4-cactus_en_Chap09_info-pratiques_ed02-2014
When your vehicle's battery is discharged, the engine   can   be   started   using   a   slave   battery  
(

external   or   on   another   vehicle)   and   jump   lead  
c

ables.
Starting using another
battery
F Operate   the   starter   on   the   broken   down  v
ehicle   and   let   the   engine   run.
 I

f   the   engine   does   not   start   straight   away,  
s

witch   off   the   ignition   and   wait   a   few  
m

oments   before   trying   again.
F
 
R

emove
 
the
 
plastic
 
cover
 
from
 

the
 
(+)
 
terminal,
 
if
 
your
 
vehicle
 
has
 
one.
F

C

onnect the red cable to the positive
terminal
 
(+)
 
of
 
the
 
flat
 
battery
 
A
, then to the
positive
 
terminal
 
(+)
 
of
 
the
 
slave
 
battery
 
B.
F
 
C

onnect
 
one
 
end
 
of
 
the
 
green
 
or
 
black
 
c

able
 
to
 
the
 
negative
 
terminal
 
(-)
 
of
 
the
 
s

lave battery B
 
(or
 
earth
 
point
 
on
 
the
 
other
 
v

ehicle).
F
 
C

onnect
 
t

he
 
o

ther
 
e

nd
 
o

f
 
t

he
 
g

reen
 
o

r
 
b

lack
 
c

able to the earth point C
 
on
 
the
 
broken
 
d

own
 
vehicle
 
(or
 
on
 
the
 
engine
 
mounting).
F
 
S

tart
 
the
 
engine
 
of
 
the
 
vehicle
 
with
 
the
 
g

ood
 
battery
 
and
 
leave
 
it
 
running
 
for
 
a
 
f

ew minutes. First
 
check
 
that
 
the
 
slave
 
battery
 
has
 
a
 
n

ominal
 
voltage
 
of
 
12
 
V
 
and
 
a
 
capacity
 
a

t
 
least
 
equal
 
to
 
that
 
of
 
the
 
discharged
 
b

attery.
Do
 
not
 
try
 
to
 
start
 
the
 
engine
 
by
 
c

onnecting
 
a
 
battery
 
charger.
Do
 
not
 
disconnect
 
the
 
(+)
 
terminal
 
when
 
t

he
 
engine
 
is
 
running.
Before disconnecting the battery
Wait 2 minutes after switching off the ignition b
efore   disconnecting   the   battery.
Close the windows and the doors before
disconnecting
  the   battery.
Following reconnection of
the battery
Following reconnection of the battery, switch on t
he   ignition   and   wait   1   minute   before   starting   to  
p

ermit   initialisation   of   the   electronic   systems.  
H

owever,   if   problems   remain   following   this  
o

peration, contact a CITR
oËn
dealer or a
qualified
 w

orkshop.
Referring
  to   the   corresponding   section,   you  
m

ust
 y
ourself
 r
einitialise
 (
depending
 o
n
 ve

rsion):
-
 
t
he   remote   control   key,
-
 ...
F

 
W

ait
 
until
 
the
 
engine
 
returns
 
to
 
idle
 
then
 
d

isconnect
 
the
 
jump
 
lead
 
cables
 
in
 
the
 
r

everse
 o

rder.
F
 
R

efit
 
the
 
plastic
 
cover
 
to
 
the
 
(+)
 
terminal,
 
if
 
y

our
 
vehicle
 
has
 
one.
Practical information

203
C4-cactus_en_Chap09_info-pratiques_ed02-2014
Changing a wiper blade
F Within  one   minute   after   switching   off  t
he   ignition,   operate   the   wiper   stalk   to  
p

osition the wiper blades vertically on the
windscreen.
Removing
F Raise   the   corresponding   wiper   arm.
F P ull the screenwash delivery pipe to
disconnect
  it   from   the   jet   (located   on   the  
w

iper   blade).
F
 
U
nclip   the   wiper   blade   and   remove   it.
Fitting
F Put  the   corresponding   new   wiper   blade   in  p
lace   and   clip   it.
F

C
onnect the screenwash delivery pipe to
the
  jet   on   the   wiper   blade.
F
 
F
old   down   the   wiper   arm   carefully.
After fitting a front wiper
blade
F Switch  on   the   ignition.
F  O perate   the   wiper   stalk   again   to   park   the  
w

iper   blades.
Before removing a front
wiper blade
9
Practical information

205
C4-cactus_en_Chap09_info-pratiques_ed02-2014
Towing another vehicle
F On  the   rear   bumper,   press   the   bottom   of  t
he   cover   to   unclip   it.
F
 
S
crew   the   towing   eye   in   fully.
F
 
I
nstall   a   towing   arm.
F
 
S
witch   on   the   hazard   warning   lamps   on  
b

oth   vehicles.
F
 
M
ove   off   gently   and   drive   slowly   over   a  
s

hort   distance   only.
F
 O
n
 
the
 
front
 
bumper,
 
press
 
at
 
the
 
bottom
 
of
 t
he
 
cover
 
to
 
unclip
 
it.
F
 
S

crew
 
the
 
towing
 
eye
 
in
 
fully.
F
 
I

nstall
 
a
 
towing
 
arm.
F
 
P

ut
 
the
 
gear
 
lever
 
into
 
neutral
 
(control
 
N for
an
 
electronic
 
gearbox).
Towing the vehicle
Failure to follow this instruction could
lead   to   damage   to   certain   components  
(

brakes,   transmission,   ...)   and   the  
a

bsence   of   braking   assistance   on  
r

estarting   the   engine. F
 
U
nlock   the   steering   by   turning   the   ignition  
k

ey   one   notch   and   release   the   parking  
b

rake.
F  
S
witch   on   the   hazard   warning   lamps   on  
b

oth   vehicles.
F  
M
ove   off   gently   and   drive   slowly   over   a  
s

hort   distance   only.
9
Practical information

219
C4-cactus_en_Chap10_verifications_ed02-2014
Checking levels
Take care when working under the bonnet, as certain areas of the engine may be extremely hot (risk of burns) and the cooling fan could start at any   time   (even   with   the   ignition   off).
Engine oil level
The check is carried out either when the   ignition   is   switched   on   using   the  
o

il   level   indicator   in   the   instrument  
p

anel   for   vehicles   so   equipped,   or  
u

sing   the   dipstick.Checking using the dipstick
Refer to the "Petrol engine" or "Diesel engine" section   for   the   location   of   the   dipstick   in   the  
e

ngine   compartment   of   your   vehicle.
F
 
T
ake   the   dipstick   by   its   coloured   grip   and  
r

emove   it   completely.
F
 
W
ipe   the   end   of   the   dipstick   using   a   clean  
n

on-fluffy   cloth.
F
 
R
efit   the   dipstick   and   push   fully   down,   then  
p

ull   it   out   again   to   make   the   visual   check:  
t

he   correct   level   is   between   the   marks   A
and B .
Check
 
all
 
of
 
these
 
levels
 
regularly,
 
in
 
line
 
with
 
the
 
manufacturer's   service   schedule.   Top   them   up   if   necessary,   unless   other wise   indicated.
If
 
a
 
level
 
drops
 
significantly,
 
have
 
the
 
corresponding   system   checked   by   a   CITROËN   dealer   or   a   qualified   workshop.
If you find that the level is above the A   mark   or  
belo

w the B   mark,   do not star t the engine.
-

I
f the level is above the MAX
 
mark   (risk  
o

f   damage   to   the   engine),   contact   a  
C

ITROËN   dealer   or   a   qualified   workshop.
-

I
f the level is below the MIN
 
mark,   you  
m

ust   top   up   the   engine   oil.
A = M
aX
B

= MI
nT

o
 
ensure
 
that
 
the
 
reading
 
is
 
correct,
 
y

our
 
vehicle
 
must
 
be
 
parked
 
on
 
a
 
level
 
s

ur face
 
with
 
the
 
engine
 
having
 
been
 
off
 
f

or
 
more
 
than
 
30
 
minutes.
It
 
is
 
normal
 
to
 
top
 
up
 
the
 
oil
 
level
 
between
 
t

wo
 
services
 
(or
 
oil
 
changes).
 
CITROËN
 
r

ecommends
 
that
 
you
 
check
 
the
 
level,
 
and
 
top
 
u

p
 
if
 
necessary,
 
every
 
3
 
000
 
miles
 
(5
 
000
 
kms).
10
Checks

220
C4-cactus_en_Chap10_verifications_ed02-2014
After topping up the oil, the check when switching   on   the   ignition   with   the   oil  
l

evel   indicator   in   the   instrument   panel  
i

s   not   valid   during   the   30   minutes   after  
t

opping   up.Oil grade
Before topping-up the oil or changing the oil, check   that   the   oil   is   the   correct   grade   for   your  
e

ngine   and   conforms   to   the   manufacturer's  
r

ecommendations.
Topping up the engine oil level
Refer to the "Petrol engine" or "Diesel engine" s ection for the location of the oil filler cap in the
engine
  compartment   of   your   vehicle.
F

U
nscrew the oil filler cap to reveal the filler
aperture.
F
 
A
dd   oil   in   small   quantities,   avoiding   any  
s

pills   on   engine   components   (risk   of   fire).
F
 
W
ait   a   few   minutes   before   checking   the  
l

evel   again   using   the   dipstick.
F
 
A
dd   more   oil   if   necessary.
F
 
A
fter   checking   the   level,   carefully   refit   the  
o

il   filler   cap   and   the   dipstick   in   its   tube.
Engine oil change
Refer to the manufacturer's service schedule for   details   of   the   interval   for   this   operation.
In
  order   to   maintain   the   reliability   of   the   engine  
a

nd   emission   control   system,   never   use  
a

dditives   in   the   engine   oil.
Checks

232
C4-Cactus_en_Chap12a_bTa_ed02-2014
EMERGENCY OR ASSIST ANCE CALL
CITROËN Localised Emergency Call
In an emergency, press this button for more than 2 seconds.
  Flashing   of   the   green   LED   and   a   voice  
message

  confirm   that   the   call   has   been   made   to   the  
CITROËN

  Localised   Emergency   Call   centre*.
Pressing
 
this
 
button   again   immediately   cancels   the   call.  
The
  green   LED  
goes

 
off.
Pressing
 
this
 
button   (at   any   time)   for   more   than   8   seconds   cancels   the  
call.
CITROËN Localised Assistance Call
When the ignition is switched on, the green LED  comes   on   for   3   seconds   indicating that

  the   system   is   operating   correctly.
If
  the   orange   LED   flashes:   there   is   a  
system

  fault.
If
  the   orange   LED   is   on   continuously:   the  
backup

  battery   must   be   replaced.
In either case, contact a CITR
o Ë n
dealer.
Pressing
 
this
 
button
 
again
 
immediately   cancels   the   request.
The
 
cancellation
 
is
 
confirmed
 
by
  a   voice   message.
Press
 
this
 
button   for   more   than   2   seconds   to   request  
assistance

 
if
 
the
  vehicle   breaks   down.
A
 

voice
 
message   confirms   that   the   call   has   been   made*.
Operation of the system
The green LED remains on (without flashing) when communication is established.
  It   goes   off   at   the   end   of   communication.
This
  call   is   dealt   with   by   the   CITROËN   Localised   Emergency   Call   centre  
which

  receives   locating   information   from   the   vehicle   and   can   send   a  
detailed

  alert   to   the   appropriate   emergency   services.   In   countries   in  
which

  the   team   is   not   operational,   or   when   the   locating   service   has  
been

  expressly   declined,   the   call   is   dealt   with   directly   by   the   emergency  
services

  (112)   without   the   vehicle   location.
If
  an   impact   is   detected   by   the   airbag   control   unit,   and  
independently

  of   the   deployment   of   any   airbags,   an   emergency   call  
is

  made   automatically.
*
 
These
  services   are   subject   to   conditions   and   availability.
 Consult

  a   CITROËN   dealer. If
  you   purchased   your   vehicle   outside   the   CITROËN   dealer   network,  
we

  invite   you   to   have   a   dealer   check   the   configuration   of   these   services  
and,

  if   desired,   modified   to   suit   your   wishes.   In   a   multi-lingual   country,  
configuration

  is   possible   in   the   official   national   language   of   your   choice.
For
  technical   reasons,   particularly   to   improve   the   quality   of  
T
elematic  
services

  to   customers,   the   manufacturer   reserves   the   right   to   carry   out  
updates

  to   the   vehicle's   on-board   telematic   system.
If
  you   benefit   from   the   CITROËN   Connect   Box   offer,   you   also   have  
available additional services in your MyCITR

o Ë n personal space,
via the CITR
o Ë n Internet website in your country, accessible on
www.citroen.com.

02
236Selecting   the   audio   source   (depending   on   version):
-  
"FM"
  /   "AM"   /   "DAB"*   stations.
-  
"USB"
  memory   stick.
-  
CD
  player   (located   under   the   right   hand   front   seat)**.
-  
Jukebox*,
  after   first   copying   audio   files   to   the   internal   memory   of   the   system.
-  
T
elephone   connected   by   Bluetooth*   and   audio   streaming   Bluetooth*   (streaming).
-  
Media
  player   connected   to   the   auxiliary   socket   (jack,   cable   not   supplied).
The   screen   is   of   the   "resistive"   type,   it   is   necessary   to   press   firmly,   particularly   for   "flick"   gestures   (scrolling   through   a   list,   moving   the   map...).  

A 
simple   wipe   will   not   be   enough.   Pressing   with   more   than   one   finger   is   not   recognised.
The   screen   can   be   used   when   wearing   gloves.  
This
  technology   allows   use   at   all   temperatures.
FIRST STEPS
* Depending on equipment.
**  
The
  CD   player   is   available   as   an   accessory   from   CITROËN   dealers.
To
  clean   the   screen,   use   a   soft   non-abrasive   cloth   (spectacles   cloth)   without   any   additional   product.
Do   not   use   pointed   objects   on   the   screen.
Do   not   touch   the   screen   with   wet   hands.
With   the   engine   running,   press   to   mute  
the

  sound.
With   the   ignition   off,   press   to   switch   the  
system

  on.
Volume   adjustment   (each   source  
is

  independent,   including  
T
raffic  
announcements

  (TA)   and   navigation  
instructions).
Following
  prolonged   operation   in  
sunny

  conditions,   the   volume   may  
be

  limited   to   protect   the   system.  
The
 
return

  to   normal   takes   place   when  
the

  temperature   in   the   passenger  
compartment

  drops.
Short-cuts:   using   the   touch   buttons   in   the  
upper band of the touch screen tablet, it
is

  possible   to   go   directly   to   the   selection  
of

  audio   source,   the   list   of   stations   (or  
titles,

  depending   on   the   source)   or   to   the  
temperature

  setting.