tow Citroen C4 PICASSO 2008 1.G User Guide

AII
95
Activation / Deactivation
You can activate/deactivate the parking assistance by pressing cont
rol A. If the parking assistance is inactive, the warning lamp is on.
Activation or deactivation of the parking assistance is memorised wh en you stop the vehicle.
Notes :
- The rear parking assistance is deactivated automatically if a trailer is attached to the vehicle. The fi tting of the towbar should be carried out by a CITROËN dealer.- The rear parking assistance is deactivated automatically if a trailer is attached to the vehicle. The fi tting of the - The rear parking assistance is deactivated automatically if a trailer is attached to the vehicle. The fi tting of the
- The proximity sensors will not be able to detect obstacles that are situated immediately below or abo ve the bumpers.
- A thin object such as a spike, or a bollard or other similar object, will be detected only at the start of the manœuvre, not when the vehicle has arrived up close.
- In bad weather or in winter, make sure that the sensors are n ot covered by dirt, or by ice or snow.
P A R K I N G A S S I S T A N C E

E
III
117
“CINEMA SEAT" POSITION
This position allows you to free up space between the fi rst row and the second row.
Pull the control E under the seat.
Note : This position is only pos-sible with the lateral seats.
ACCESS TO THE THIRD ROW SEATS
The third-row seats can be accessed via the lateral second-row seats.
1. Pull the control E. The seat un-locks and the seat base comes up against the backrest.
2. Hold the control E in the raised position, pushing forwards. The whole slides towards the front seat.
3. Raise and lock the rigid plate.
Space becomes free behind the seat, the third-row passengers can get to their seats.
To exit the third-row seat positions :
1. Hold the control E in the raised position. The seat unlocks and the seat base comes up against the backrest.
2. Push the seat backrest, still holding the control E in the raised position.
Note : if the table on the back of the fi rst-row seat is down, close it to enable this operation.
Repositioning the seat,
from the exterior,
with the door open
If there are passengers seated in the third row :
1. Manually return the assembly as far as possible rearwards. The seat does not return as far as the maximum rearwards position, so as to retain leg space for the third-row pas-sengers.
2. Fold the seat base.
S E C O N D R O W S E A T S G R A N D C 4 P I C A S S O

1
2
3
G
F
118
III
CONCERTINA PLATES
Two rigid concertina plates, which cannot be separated from the ve-hicle, cover the 2 third-row seats, when these are in the folded posi-tion.
To fold the concertina plates :
Pull on the control, the 3 sections of the plate will fold like a concer-tina.
When the third-row seats are up-right, these concertina plates can be left either :
- fl at behind the seats,
- in the vertical position,
thereby leaving a storage area available.
TO RETURN THE SEATS TO
THE UPRIGHT POSITION
1. Return the second-row rigid plates to their initial position and lock them.
2. Having folded your concer-tina plate, pull on the control F located behind the seat backrest. The backrest pivots rearwards, pulling the seat base with it. The seat locks in the open position.
TO STOW THE SEATS
1. Return the second-row rigid plates to their initial position and lock them.2. Lower the head restraints.3. Correctly position the concer-tina plate vertically behind the seat.4. Pull on the control G located at the bottom of the seat back-rest. The seat unlocks.5. Next push the backrest gently forwards. The backrest pivots, folding onto the seat base. The seat base then folds into the stowage area provided for that purpose.6. Reposition the concertinaplates over the folded seats.
Before moving the third-row seats, return the rigid plates of the second-row seats to the upright position and lock them.
Do not try to fold a third-row seat that has not fi rst had the backrest fully locked in place.
Do not leave objects either on or underneath the seat bases of the third-row seats when you are folding them.
Do not leave your hand on the control G as you fold the seats, as you risk trapping your fi ngers.
T H I R D R O W S E A T S G R A N D C 4 P I C A S S O

III
119
A Lounge version is available in the 5 seater model. This has two se-cond-row seats that are identical to the fi rst-row seats, providing greater comfort for rear passengers.
ADJUSTING THE SEATS
The seats have the following adjust-ments :
- head-restraint adjustment,
- backrest angle,
- greater longitudinal adjustment,
- height-adjustable armrests.
Refer to the page " FRONT SEATS - Manual adjustments " for the operation of the adjustment controls.
LUGGAGE COVER BEHIND
THE SEATS
A fl exible luggage cover positio-ned behind the second-row seats enables you to prevent objects from sliding under or between the second-two seats, as well as concealing the contents of your boot from outside view.
It is fi xed to the fl oor by two hooks located behind the seats and an-chored at special points on the rear pillars.
This fl exible luggage cover is mo-vable and can be rolled up for stowage behind the second-row seats.
SEAT BELTS
For safety reasons, always attach your seat belt before positioning the armrest between yourself and the door.
STORAGE POCKETS
Two storage pockets are located on the insides of the Lounge ver-sion seats.
F E A T U R E S O F T H E 4 S E A T E R
L O U N G E V E R S I O N

C
D
A
BB
121
R E A R C E N T R A L S E A T B E L T C 4 P I C A S S O A N D G R A N D C 4 P I C A S S O
Routing of the seat belt (C4 Picasso and C4 Grand Picasso)
- Insert the tongue C into the buckle on the right, then insert the second tongue D into the buckle on the left.
Before use
For safety reasons, it is essential that the seat belt passes through the relay ring.
To prevent any damage to seat belts and in order not to get them jammed, take care to stow them on the sides of the backrests.
Installation of the seat belt (C4 Picasso)
1. Open the cover A.
2. Remove the belt tongues from their housing.
3. Bring the belt tongues up to the relay ring B.
4. Insert the attachment then pass the tongues through the ring.
5. Reclose the cover A. Make sure that the belt is correctly positioned in the recess in the cover provided for this pur-pose.
Stowage of the belt tongues (C4 Picasso)
- Operate in reverse order to stow the belt tongues.
Note : You may opt to leave the seat belt in the relay ring even if not using it.

122
III
Stowing the tongue of the third-row seat belt
Secure the tongue in the place provided on the rear pillar trim.Note : The third-row passenger seat belts that are not being used can be stowed in order to free up load-space and facilitate use of the luggage cover.
Requirements for the third-row passenger seat belts
Take care to attach the third-row passenger seat belts on the rings provided for this purpose.
Do not attach the belts on the anchoring points marked with a red cross (see illustration above).
T H I R D R O W S E A T B E L T S G R A N D C 4 P I C A S S O
Before use :
To avoid damaging or jamming the seat belts, take care to stow them on the sides of the backrests.

A
B
C
III
A I R C R A F T - S T Y L E R E A R T A B L E S
Rear tables
The backrests of the front seats are fi tted with aircraft-style tables. These incorporate a cup-holder A and a retaining strap B, for the placing of objects.
Operation
- Pull the table downwards to open.
- To restow the table, raise it until the latch locks.
Note : For safety reasons, these collapse downwards if excessive pressure is exerted.
Individual reading lamps
Reading lamps C may be incorporated in the front seat backrests, behind the tables. These light the surface of the tables without disturbing the other passengers.
They are accessible only while the table is down.
- Press on the On/Off button to turn the lamp on or off.
Rear table stowedRear table opened

III
145
MODUBOX
The Modubox is for use both inside the vehicle and away from the vehicle. It is composed of a shopping trolley and a fl exible bag (isotherm on some versions) which can be used independently of each other de-pending on your needs (by detaching the fastenings on each side at the top and bottom).
To use
1. Unhook the red strap to free the Modubox.
2. Unhook the black strap then press on the round buttons on either side of the Modubox simultane-ously to deploy it.
B O O T M O D U B O X - C 4 P I C A S S O
Use of the Modubox outside the vehicle
- Press on the recess on the left hand side of the Modubox to raise (or lower) the handle.
Stowage inside the vehicle
- Perform the operations in reverse to fold and stow inside the vehicle.
- If you have used your Modubox away from the vehicle, take care to reposition it correctly in the housings pro-vided for this purpose.

IV
R A D I O S O U R C E
Notes on radio reception
Your radio will be subject to certain phenomena that are not encoun-tered by domestic systems.
The reception of AM and FM sig-nals may suffer from interference, which is caused by the nature and propagation of the signals and does not refl ect on the quality of your radio installation.
In AM, the reception may be af-fected when passing under power lines or bridges, or when travelling through tunnels.
In FM mode, the reception may be affected by the distance from the station transmitter, the refl ecting of signals off obstacles (mountains, hills, tower blocks) and radio blacks-pots (no coverage from the station transmitter).
Selection of radio source
Press button D to select the source.
Selection of frequencies and memory banks
Press button E successively to go through the memory banks FM1, FM2 and FM3, for the FM wave-band, and the memory banks MW/LW, for the AM waveband.
Manual search
Manual search is via buttons J or M.
By keeping button J or M pressed, you will be able to scroll through the waveband. Scrolling will stop as soon as you release the button. The radio will remain tuned to the frequency that is displayed.
Tuning sensitivity
Automatic searches can be car-ried out according to two levels of sensitivity :
- To capture the most powerful trans-mitters, choose the local search mode “LO” (default option).
- To capture the weakest or most distant transmitters, choose the sensitive search mode “DX”.
Search for a station is done fi rst in “LO” (local) sensitivity, then in “DX” (distant) sensitivity.
To commence a search in sensi-tivity “DX” (distant) immediately , press twice in succession on one of the buttons K or N.
Automatic search
A short press on one of the but-tons K or N will tune into higher or lower radio stations respectively, within the chosen waveband.
By keeping button K or N pressed, you will be able to scroll through the waveband. The scrolling will stop at the fi rst station it fi nds once the button is released.
You can also do this by means of control 2 at the steering wheel.
If the automatic search is unable to tune into a known frequency (perhaps owing to very weak re-ception), it is possible to search manually to fi nd this station.
Display and selection of a station available in the area in which you are travelling
Briefl y press on button G to bring up a list of stations, this is updated every 10 minutes.
You can also update this list at any time by giving a long press on button G.
To listen to one of these stations, select by pressing buttons J or Mand validate using button L.

3
2
1
4
186
VIREAR LENS
Note the bulb that is faulty.
Bulbs :
 Direction indicator : PY21W.
 Stoplamp : P21W.
 Reversing lamp : P21W.
 Sidelamp : LED
Contact a CITROËN dealer.
Rear lamps
1. With the tailgate open, undo the 3 screws located on the side of the lens unit and pull it rearwards to detach.
2. Disconnect the connector lin-king the lens unit to the boot. Do not disconnect the LEDs.
3. Remove the seal.
4. Remove the bulb-holder.
5. Replace the bulbs. To remove a bulb, rotate it a quarter turn. To fi t the bulb, rotate it a quarter turn in the other direction.
6. Reposition the bulb-holder.
7. Put back the seal.
8. Reconnect the connector to the lens unit.
9. Stow the harness in the open-ing provided in the bodywork.
10. Reattach the lens unit on the bodywork and do up the 3 screws.
Third stoplamp with bulb
1. With the boot open, detach the interior trim.
2. Undo the nuts.
3. Using a thin screwdriver, de-tach the 3 retaining lugs.
4. Remove the lamp via the ex-terior of the tailgate.
5. Remove the bulb-holder.
6. Change the faulty bulb(s).
Check that the vehicle lamps work correctly after each operation.
C H A N G I N G B U L B S
R E A R L E N S - G R A N D C 4 P I C A S S O
Third stoplamp with LED
Contact a CITROËN dealer