P off Citroen C4 PICASSO 2008 1.G Owner's Guide

12II
83
Automatic photochromic interior rear view mirror
It modifi es its role automatically and progressively between day use and night use.
In order to prevent dazzle, the glass automatically darkens as a func-tion of the intensity of light coming from behind. It lightens as this di-minishes, thus giving you optimum visibility.
Operation
With the ignition on, press on con-trol 1. - Warning lamp 2 on : automatic mode. - Warning lamp 2 off : end of auto-matic mode. The glass remains in its lightest defi nition.
Note : For optimum visibility, the glass lightens automatically when you engage reverse gear.
The lever on the bottom edge of the interior rear view mirror enables it to be placed in two positions :
Day position : the lever is not visible.
Night position (anti-dazzle) : the lever is visible.
Permit reader
The athermic windscreen comprises a zone situated on either side of the base of the child mirror, to enable access permits to be read (e.g. mo-torway toll permit).
Child mirror
A child monitoring mirror is installed above the interior rear view mir-ror. This allows you to monitor the vehicle’s rear passengers, or it can facilitate conversation between the front and rear passengers without the need to move the rear view mir-ror. It can be folded away to elimi-nate dazzle.
I N T E R I O R R E A R V I E W M I R R O R

88
II
Stopping the function
- by an action on the control on position "REG" to position 0.
- by the engine stopping.
The cruise speed previously cho-sen is no longer memorised.
If there is a malfunction,a mes-sage will display accompanied by a sound signal and lighting of the SERVICE warning lamp.
Contact a CITROËN dealer.
Cruise control should only be used when the driving conditions allow you to drive at a constant speed.
Do not use it in heavy traffi c, or on dangerous or slippery roads.
The driver must remain attentive and in full control of his vehicle.
You are recommended to keep your feet within range of the pe dals.
To avoid any risk of interfering with the pedals :
- check that the fl oor mat is correctly positioned,
- never use more than one fl oor mat.
Re-engaging cruise control
-by recall of the memorised speed :
After a disengagement, press on button 3. Your vehicle automati-cally returns to the memorised cruise speed which is displayed in zone A.
If the memorised cruise speed is higher than the current speed, the vehicle wll accelerate to reach the former.
- by selection of the current speed :
Press on button 2 or 4 once the desired speed has been reached.The information "OFF" will thendisappear from zone A.
Observation : If during the opera-tion of cruise control, the system is unable to keep within the memo-rised speed (for example on a steep descent), then the speed fl ashes. Adapt your speed as necessary.
Disengaging of cruise control while retaining the memorised speed
- Either by pressing on the brake pedal or on the clutch pedal.
- Or by pressing button 3.
- Or if either the ESP or the ASR system is active.
Note : cruise control is not active if the gear lever is in neutral.
These actions cause the informa-tion "OFF" to appear in zone A of the instrument panel.
These manœuvres do not cancel the cruise speed which remains displayed in the instrument panel.
C R U I S E C O N T R O L

1
3
4
2
A
II
89
This driving assistance device en-ables you to choose a maximum speed that you wish not to exceed. This has to be higher than 30 km/h (around 20 mph).
The speed limiter controls are lo-cated on the steering wheel.
Note : The information relating to the speed limiter is displayed in zone A of the instrument panel.
Selection of the function
Rotate the control 1 to the "LIM"position.
On selection of the function, the previous memorised speed and the information "OFF" are displayed :
Adjustment of the maximum speed
With the engine running, you can adjust the memorised maximum speed , by means of short or long presses on :
- button 4 to increase the memo-rised maximum speed,
- button 2 to decrease the memo-rised maximum speed.
Note : successive presses will modify the maximum speed in steps of 1 km/h and a sustained press in steps of 5 km/h (3 mph).
Activation of the maximum speed
When the desired maximum speed is displayed, press button 3 so that the limitation is activated.The information "OFF" thendis-appears from zone A.While the function is active, press-ing the accelerator pedal will not en-able the programmed speed to be exceeded, except if you press the pedal hard down to beyond the end-of-travel switch (see “Temporary override of the maximum speed”).
Note : The speed of your vehicle may vary slightly in relation to that memorised.
Bi-tone instrument panel
S P E E D L I M I T E R

90
II
Stopping the function
- by an action on the control on position "LIM" to position 0.
- by the engine stopping.
The speed previously chosen is still memorised.
If there is a malfunction,a mes-sage will display accompanied by a sound signal and lighting of the SERVICE warning lamp.
Contact a CITROËN dealer.
Temporary override of the maximum speed
The accelerator pedal is equipped with an end-of-travel switch. If you action this switch by pressing the pedal hard down, you can exceed the memorised maximum speed at any time.
During the time the speed is being exceeded, the displayed speed fl ashes.
You have only to release the ac-celerator pedal to return below the maximum speed and render the function active again.
Observation : If during the operation of the speed limiter, the system is unable to keep within the maximum speed (for example on a steep de-scent or under heavy acceleration) then the speed fl ashes. Adapt your speed as necessary.
The function will re-engage when your speed returns below the de-sired maximum speed.
Disengagement of the maximum speed
Press on button 3.
This action causes the information "OFF" to appear on the instru-ment panel screen.
Use of fl oor mats that are not approved by CITROËN may hinder access to the accelerator pedal and thus interfere with the func-tioning of the speed limiter.
To avoid any risk of interfering with the pedals :
- check that the fl oor mat is correctly positioned,
- never use more than one fl oor mat.
This action does not cancel the memorised maximum speed which remains displayed in zone A ofthe instrument panel.
S P E E D L I M I T E R

A
92
II
This driving assistance device alerts you if you are wandering from your lane (continuous or dotted line marking on the road surface).
It is designed especially for use on motorways and dual carriage-ways, operating only at speeds above 80 km/h (approx. 50 mph).
Activation / Deactivation
A press on control A activates the function, the warning lamp on the control lights up.
A second press on control A de-activates the function, the warning lamp on the control goes out.
Whenever you start the engine, the mode (activated/deactivated), selected when you last switched off the engine, is retained.
The driver must still remain attentive and in complete control of the ve-hicle.
Operation
Provided you are travelling at over 80 km/h (approx. 50 mph), if you cross a lane marking, you are alerted by a vibration within the cushion of your seat :
- oriented to the right for crossing a lane marking to the right,
- oriented to the left for crossing a lane marking to the left.
The system does not alert you while your direction indicator is o perating, nor for about 20 seconds after your direction indicator has stopped.
Note : In the event of an electronic malfunction, a message is displayed, the SERVICE warning lamp comes on and a sound signal is heard. Con-tact a CITROËN dealer. warning lamp warning
Observations : This device is designed to identify traffi c lane markings.
In certain specifi c instances, it may trigger an unwanted alert, for example when you cross a direction arrow or some other random marking.
The effectiveness of the system may be temporarily affected by condi tions external to the vehicle :
• Detection of lanes made diffi cult by:
- Markings that are worn or erased.
- Insuffi cient contrast with the surface of the road.

A
96
III
Electrical control
From the driver’s seat position, the controls siutated on the door enable the vehicle’s electric win-dows to be actioned.
Note : The windows can also be operated for a short time after the ignition has been switched off (in-cluding after the front doors have been opened).
Sequential control
An action to the fi rst notch on the control starts a window movement which stops when the control is released. A press for about one second on the control will close or open the window fully, a further press will stop the movement.
PAY ATTENTION TO WHERE CHILDREN ARE WHEN OPERATING THE ELECTRIC WINDOWS.
Always remove the key from the ignition when leaving the vehicle, even for a short time.
When the driver is actioning the controls for the passenger win dows, he must make sure that no-one is obstructing the windows from lo sing properly.
The driver should ensure that the passengers use the windows cor-rectly.
If any person should be at risk of becoming trapped by the operation of the windows, you must reverse the movement of the glass. For t hat, reverse the position of the control concerned.
This is for deactivating operation of the electric windows and opening of the rear doors from the rear seat positions. It is activated by a press on the control A located on the window control panel or by an action on the locks of the rear doors. The warning lamp in the instrument panel comes on temporarily. Each time you switch on the ignition, the warning lamp lights up for a short time.
It is still possible to open the doors from the outside and to operate the rear windows from the front seat positions.
Anti-pinch
An anti-pinch device will stop the glass from rising. If it meet s an obstacle, it goes back down.
After a battery disconnection or following a malfunction, you have to re-initialise theanti-pinch function for each window :
- Use the control to open the window fully, then attempt to close it. It will rise only a few centimetres.
- Pull again on the control until the window closes fully. Once the window is closed, sustain the press on the control for one second.
Warning : During this operation, the anti-pinch protection is inoperat ive.
Child safety
E L E C T R I C W I N D O W S

A
III
97
If you decide to drive with the doors locked, be aware that this will make access more diffi cult for the emergency services in the event of an accident.
Note : the control A is inactive when the vehicle has been locked by means of the remote control or the key
Door selectivity
If you have selected “plip action : driver’s door" in the multifunction screen menu :
- a press on the remote control opens the driver’s door,
- a second press opens all the doors.
Anti-intrusion security
On starting the vehicle, the system automatically locks the doors w hen you have reached a speed of around 10 km/h (6 mph).
Note : Whenever a door is opened, the door will lock again automatically when the vehicle reaches a speed of around 10 km/h (6 mp h).
Activation / Deactivation of the function
After switching on the ignition, give a long press on the ce ntral unlocking control until you see a message displayed and a sound signal is emitted.
Locking from the inside
A press on the control A operates the electric central locking and un-locking, provided the doors and tailgate are closed.
The doors can still be opened from the inside.
If one of the doors is open or not properly closed, the central lock-ing does not operate.
The warning lamp on the control A signals 3 statuses :
- It fl ashes when the doors are locked, with the vehicle stationary and the engine turned off.
- It lights up when the doors are locked, or when the ignition is switched on.
- It goes out if the doors are not locked.
A C C E S S T O T H E V E H I C L E

1234
5
6
7
8
III
101
V E N T I L A T I O N - H E A T I N G M A N U A L A I R C O N D I T I O N I N G
A. DRIVER’S CONTROL PANEL
1 - Adjustment of the air blower speed
The air blower adjustment only operates when the en-gine is running.
To adjust the air fl ow, press on button :
The air distribution chosen is shown by the lighting of the corresponding warning lamps at 9.
to increase the fl ow of air
to decrease the fl ow of air
The level of air fl ow is shown by the progressive lighting of the warning lamps depicting the ventilator blades.
By decreasing the fl ow to zero, you deactivate the air conditioning system (OFF).
Note : to achieve an agreeable level of comfort in the passenger compartment, you should not leave this control too long in the OFF position.
3 - Mode of adjustment of temperature for the passenger
- Press on button 3 to have independent passenger control of cabin air temperature. The warning lamp goes out.
Note : While the passenger is adjusting temperature, the warning lamp lights up.
4 - Air recirculation
This control is for isolating disagreeable odours or fumes coming from outside.
- Press on button 4, to exclude entry of outside air. The warning lamp lights up.
This should be cancelled as soon as possible to permit renewal of cabin air and to prevent misting.
- Press again on button 4, to deactivate air recirculation.
5 - Air conditioning
The air conditioning can only operate when the engine is running. The air blower control (adjusting the fl ow of air) has to be activated in order for air conditioning to be obtained.
- Press on button 5. The warning lamp lights up.
To be effective, the air conditioning should be operated only with the windows closed.only
2 - Adjustment of the air distribution
- Press on button 2 to make the display scroll through the different types of air distribution.

1
102
III
B. PASSENGER’S CONTROL PANEL
Adjustment of temperature
- Press on button 1 to take over control of the tem-perature. The warning lamp on button 1 lights up.
- Rotate button 1 to adjust your temperature.
Note : The adjustment of the temperature is continuous and progressive starting from one side.
V E N T I L A T I O N - H E A T I N G M A N U A L A I R C O N D I T I O N I N G
Observation : If your vehicle is not equipped with air conditioning, you will have the same control panel but without the A/C button.
6 - Deicing / demisting of the rear screen
This operates only if the engine is running.
- Press on button 6 to activate/deactivate the electric deicing/demisting of the rear screen and the exterior rear view mirrors. The warning lamp lights up.
The deicing/demisting switches off automatically to prevent excessive consumption of power.
7 - Rapid deicing / demisting of front and rear windows and rear view mirrors
- Press on button 7. The warning lamp lights up.
This function simultaneously activates :
- front deicing/demisting,
- optimum fl ow of air,
- recirculation prohibition,
- deicing/demisting of rear view mirrors and heated rear screen,
- air conditioning if necessary.
To stop the function, press again on button 7.
8 - Adjustment of the air blower temperature
This control is for adjusting the temperature of the air in the passenger compartment. It can be used in cold weather as well as in hot weather, provided the air conditioning is active.
Note : The adjustment of the temperature is continuous and progressive starting from one side.

6
7
8
9
101
234
III
103
A U T O M A T I C A I R C O N D I T I O N I N G
1 - Automatic comfort regulation
A press on this button, confi rmed by the dis-play of the A/C warning lamp and of AUTO on the screen, provides automatic control, at the temperature selected, of all the following 5 functions :
- air fl ow,
- cabin temperature, on left hand side and right hand side,
- air distribution,
- air conditioning,
- automatic air recirculation.
For this facility to operate, it is recommended to keep all the air vents open.
Using the AUTO mode will prevent misting inside the vehicle in cold or humid weather.
Note : When starting from cold, in order to avoid a rush of cold air, the blower attains its optimum level progressively.
Manual resumption of one or more functions
It is possible to adjust each of the functions 4, 6 and 10 manually. The display of the "AUTO" function will then go off.
Resumption by the driver of the adjustment of cabin temperatures (for the front and rear passengers)
-A long press on this button will realign the tem-peratures for all passengers with the preferences of the driver.
A. DRIVER’S CONTROL PANEL